Abstract:A novel micro/nanoscale rough structured superhydrophilic hybrid-coated mesh that shows underwater superoleophobic behavior is fabricated by spray casting or dipping nanoparticle–polymer suspensions on stainless steel mesh substrates. Water droplets can spread over the mesh completely; meanwhile, oil droplets can roll off the mesh at low tilt angles without any penetration. Besides overcoming the oil-fouling problem of many superhydrophilic coatings, this superhydrophilic and underwater superoleophobic mesh can be used to separate oil and water. The simple method used here to prepare the organic–inorganic hybrid coatings successfully produced controllable micro-nano binary roughness and also achieved a rough topography of micro-nano binary structure by controlling the content of inorganic particles. The mechanism of oil–water separation by the superhydrophilic and superoleophobic membrane is rationalized by considering capillary mechanics. Tetraethyl orathosilicate (TEOS) as a base was used to prepare the nano-SiO2 solution as a nano-dopant through a sol-gel process, while polyvinyl alcohol (PVA) was used as the film binder and glutaraldehyde as the cross-linking agent; the mixture was dip-coated on the surface of 300-mesh stainless steel mesh to form superhydrophilic and underwater superoleophobic film. Properties of nano-SiO2 represented by infrared spectroscopy and surface topography of the film observed under scanning electron microscope (SEM) indicated that the film surface had a coarse micro–nano binary structure; the effect of nano-SiO2 doping amount on the film’s surface topography and the effect of such surface topography on hydrophilicity of the film were studied; contact angle of water on such surface was tested as 0° by the surface contact angle tester and spread quickly; the underwater contact angle to oil was 158°, showing superhydrophilic and underwater superoleophobic properties. The effect of the dosing amount of cross-linking agent to the waterproof swelling property and the permeate flux of the film were studied; the oil–water separation effect of the film to oil–water suspension and oil–water emulsion was studied too, and in both cases the separation efficiency reached 99%, which finally reduced the oil content to be lower than 50 mg/L. The effect of filtration times to permeate flux was studied, and it was found that the more hydrophilic the film was, the stronger the stain resistance would be, and the permeate flux would gradually decrease along with the increase of filtration times.

Preparation of Underwater Superoleophobic Porous Coating Via a Co‐deposition Method for Oil/water Mixture Separation

Superhydrophilic/underwater Superoleophobic Oil-in-water Emulsion Separation Membrane Modified by the Co-Deposition of Polydopamine and Chitosan-Tripolyphosphate Nanoparticles

Polydopamine-CaCO3 Modified Superhydrophilic Nanocomposite Membrane Used for Highly Efficient Separation of Oil-in-water Emulsions

Fabrication of a Novel Superhydrophobic and Superoleophilic Surface by One-Step Electrodeposition Method for Continuous Oil/water Separation

A Degradable Super-Hydrophilic/Underwater Super-Oleophobic Membrane Prepared by a Green Modification Method for Efficient Oil-in-Water Emulsion Separation

Ni-Al Layered Double Hydroxides (ldhs) Coated Superhydrophobic Mesh with Flower-Like Hierarchical Structure for Oil/water Separation

Fabrication of Ph-Sensitive Superhydrophilic/Underwater Superoleophobic Poly(vinylidene Fluoride)-Graft-(sio2 Nanoparticles and PAMAM Dendrimers) Membranes for Oil-Water Separation.

High Flux Durability Underwater Superoleophobic Mesh Modified by Poly (maleic Acid Mono-(2-(dimethylamino)-ethyl Ester-Co-hydroxyethyl Acrylate) and Nanosilica Particles Hybrid

Robust bio-inspired superhydrophilic and underwater superoleophobic membranes for simultaneously fast water and oil recovery

[A modern preparative method (starch gel electrophoresis) for separation and purification of hydrolases, set forth with a specific example].

Micro/Nanoscale Structured Superhydrophilic and Underwater Superoleophobic Hybrid-Coated Mesh for High-Efficiency Oil/Water Separation

Superhydrophilic and underwater superoleophobic cement-coated mesh for oil/water separation by gravity

Bioinspired superhydrophilic/underwater superoleophobic surfaces with robust wax-prevention, self-cleaning and oil/water separation function

3D antifouling hierarchical micro/nanostructures with underwater superoleophobicity via one-step electrodeposition on anode and cathode

Fast Formation of Superhydrophobic Octadecylphosphonic Acid (ODPA) Coating for Self-Cleaning and Oil/water Separation

Facile preparation and modification of robust BiOCl/Bi 2 O 3 coated mesh with superwetting and anti-biofouling performance for oil/water separation and wastewater treatment

One-Step Coating Toward Multifunctional Applications: Oil/Water Mixtures and Emulsions Separation and Contaminants Adsorption.

Cubic MOF coated stainless steel mesh with underwater superoleophobicity for highly efficient oil/water separation

Underwater Superoleophobic Surfaces Prepared from Polymer Zwitterion/Dopamine Composite Coatings

Coordination-driven In-Situ Self-Assembled Prussian Blue/alginate Hydrogels Composite Mesh with Underwater Superoleophobicity for Oil/ Water Separation and Self-Cleaning Performance

Bio-inspired super-wetting coatings constructed from interfacial mineralization of rare earth phosphate for oil/water separation applications