Abstract:Additive manufacturing (or 3D printing) for continuous fiber composite exhibits great potential for fabrication of next-generation lightweight sophisticated structural components. Nevertheless, understanding of interface characteristics of printed parts has remained an open research question for broader applications of this new technology in engineering practice. This study aimed to evaluate the interfacial quality of 3D-printed carbon fiber reinforced plastic (CFRP) composites from two aspects: interlaminar fracture toughness in a pure mode and interfacial failure mechanism in a mixed mode. Prior to the experimental tests, the microstructural quality of the 3D printed specimens was characterized, which showed that the void content and shape of different materials are different. There is a clear boundary line where the short fiber matrix layer and the continuous fiber reinforced layer are in contact, while the interface formed between the same material layers has no evident connection traces. The standard specimens were printed for testing pure mode I and mode II interlaminar fracture toughness, through which the GCYRILLIC CAPITAL LETTER BYELORUSSIAN-UKRAINIAN IC and GIIC of interface between continuous carbon fiber layers was characterized. It was found that the fiber bridging phenomenon presented in the double cantilever beam (DCB) experiments, resulting in a higher initial mode I fracture toughness. The end notched flexure (ENF) tests found that the fracture toughness of initial mode II in between the 0 degrees continuous carbon fiber layers was relatively low. The scanning electron microscope (SEM) analysis revealed that the separated surface had only a small area of the matrix being sheared. The single lap specimen printed directly was proposed as a simplified model for simulating complex structural parts subjected to mixed stress of peel and shear. The mechanical responses and failure characteristics of the interfaces composed of different materials and different fiber angles under mixed stress were studied. It is found that each specimen presented some mixed failure modes, and the interface characteristics of different materials and different fiber orientations were completely different. The results gained in-depth understanding on the interfacial properties of 3D printing fiber reinforced structures, thereby providing key data and knowledge for practical applications.

Investigations of quasi-static indentation properties of 3D printed polyamide/continuous Kevlar/continuous carbon fiber composites

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Effect of Continuous Fiber Orientations on Quasi‐static Indentation Properties in 3D Printed Hybrid Continuous Carbon/kevlar Fiber Reinforced Composites

Simultaneous Reinforcement of Both Rigidity and Energy Absorption of Polyamide-Based Composites with Hybrid Continuous Fibers by 3D Printing

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Mechanical and Energy Absorption Behaviors of 3D Printed Continuous Carbon/kevlar Hybrid Thread Reinforced PLA Composites

Process evaluation, tensile properties, mathematical models, and fracture behavior of 3D printed continuous fiber reinforced thermoplastic composites

Contributions of Interfaces on the Mechanical Behavior of 3D Printed Continuous Fiber Reinforced Composites

Mechanical, microstructural and numerical investigations of 3D printed carbon fiber reinforced PEEK

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Experimental Study on Interface Failure Behavior of 3D Printed Continuous Fiber Reinforced Composites

Effects of printing direction on quasi‐static and dynamic compressive behavior of 3D printed short fiber reinforced polyamide‐based composites

Fracture Toughness Determination and Mechanism for Mode-I Interlaminar Failure of 3D-Printed Carbon-Kevlar Composites

Tailorable Rigidity and Energy-Absorption Capability of 3D Printed Continuous Carbon Fiber Reinforced Polyamide Composites

Hybrid Layout and Additive Manufacturing of Continuous Carbon/glass Fibers Reinforced Composites, and Its Effect on Mechanical Properties

Impact Resistance of 3D-Printed Continuous Hybrid Fiber-Reinforced Composites

Investigations of three-dimensional fiber orientation on mechanical impact behavior of short glass-fiber-reinforced PEEK composites

Mechanical Characterization of 3D Printed Continuous Carbon Fiber Reinforced Thermoplastic Composites

Layout design and mechanical behavior of 3D printed intralayer hybrid continuous carbon/glass fiber composites

Flexural Properties and Fracture Behavior of CF/PEEK in Orthogonal Building Orientation by FDM: Microstructure and Mechanism