Abstract:To explore the distinction between generation atmosphere of fuel NOx and thermal NOx in an ammonia-hydrogen compound fuel engine, a numerical calculation model was established based on a detailed ammonia-hydrogen oxidation mechanism. The combustion process and NOx evolution mechanism of the ammonia-hydrogen compound fuel engine under different intake conditions were studied. The research results for different equivalence ratios show that the in-cylinder hydrogen volume is the primary factor influencing the initial heat release. When the equivalence ratio is between 0.89 and 1.14, the mixture exhibits a higher combustion rate, leading to a shorter CD and an earlier CA50. At this point, the heat release process closer to TDC contributes improving engine combustion efficiency and indicated efficiency. Therefore, when the equivalence ratio is between 0.89 and 1.00, combustion efficiency is higher than 98% and indicated efficiency is higher than 43%, the ammonia-hydrogen compound fuel engine achieves relatively higher economy. Both over-rich and over-dilute mixtures induce an enhancement of fuel NOx, while the higher in-cylinder temperature caused by stoichiometric combustion leads to a boom of thermal NOx. Consequently, the total NOx emission from the ammonia-hydrogen compound fuel engine is higher at equivalence ratios between 0.80 and 1.00, and the NOx emission reaches its peak at an equivalence ratio of 0.89. Analysis of the evolution process of key N components in the cylinder shows that incomplete combustion plays a significant role in fuel NOx emissions, while thermal NOx emissions are mainly influenced by the distribution of in-cylinder components and combustion temperature. Specifically, thermal NOx emissions primarily depend on the in-cylinder components distribution in the narrow equivalence ratio range around stoichiometric ratio, and are significantly affected by in-cylinder temperature under other conditions. The in-cylinder oxygen concentration significantly affects fuel NOx emissions under most operating conditions. Further optimization of intake temperature shows that combustion efficiency exceeds 90% when the intake temperature is above 280 K. When the intake temperature reaches 310 K, the combustion efficiency reaches up to 98%, thus an intake temperature of about 310 K is sufficient to meet the need for improving the combustion efficiency of ammonia-hydrogen compound fuel engine. To achieve high efficiency and lower NOx emissions, appropriate lean combustion combined with an intake temperature slightly above room temperature is recommended.

Parameter Optimization and Simulation of Lean-Burn Gas Generator

Multi-objective performance optimization and control for gas turbine Part-load operation Energy-saving and NOx emission reduction

Optimization of Operation Strategies of a Syngas-Fueled Engine in a Distributed Gasifier-Generator System Driven by Horticulture Waste

Numerical Simulation of HCNG Engine on GT-Power

An investigation of optimum control of a spark ignition engine fueled by NG and hydrogen mixtures

Numerical investigation on combustion regulation for a stoichiometric heavy-duty natural gas engine with hydrogen addition considering knock limitation

Optimization of a diesel/natural gas dual fuel engine under different diesel substitution ratios

Co-optimization of Miller Degree and Geometric Compression Ratio of a Large-Bore Natural Gas Generator Engine with Novel Knock Models and Machine Learning

Collaborative optimization of fuel composition and operating parameters of gasoline compression ignition (GCI) engine in a wide load range

Optimization Technology of Combustion Engine Control Based on Swarm Intelligent Optimization Algorithm and Improved Clustering Algorithm

Investigations on combustion system optimization of a heavy-duty natural gas engine

Optimization of Combustion Chamber Geometry for Natural Gas Engines with Diesel Micro-Pilot-Induced Ignition

Experimental and simulation research on the lean combustion characteristics of direct-injection hydrogen engine

Optimization of combustion organization scheme for pre-combustion chamber of pre-cooled engine

Multi-objective optimization of a hydrogen-fueled Wankel rotary engine based on machine learning and genetic algorithm

Fuel economy optimization of an Atkinson cycle engine using genetic algorithm

Influences of the Control Parameters and Spark Plug Configurations on the Performance of a Natural Gas Spark-Ignition Engine

Parametric Optimization of Engine Performance and Emissions for Hydroxy Blended Gaseous Fuels

Numerical study of the combustion process and NOx evolution mechanism of ammonia-hydrogen compound fuel engine under different intake conditions

Emission and Operational Characteristics Analysis of Axially Staged Combustors Based on Overall Parameters

Experimental Study of Stratified Lean Burn Characteristics on a Dual Injection Gasoline Engine