Abstract:Phase change phenomena in microchannels have been projected as an effective option for thermal management of various microscale systems. However, for the design of heat sinks which utilize these phenomena, a clear understanding of the physical mechanisms involved, in the microscale domain, is required. In the present study, a numerical simulation is carried out to predict the characteristics of two phase flow with liquid to vapor phase change, in rectangular microchannels for a range of hydraulic diameters. The annular flow pattern, reported to be the most common in microchannel, has been investigated, with water as the flowing medium. The analysis considers, among other parameters, the effect of surface tension on the flow dynamics, which could be significant in microchannels. The mathematical model is numerically solved using a quasi-three dimensional approach, incorporating the variations in the cross-sectional areas of both the phases along the flow direction. Since it is expected that the continuum approximation may be insufficient in the vapor domain in channels of very small dimensions, an analysis incorporating slip flow at the liquid vapor interface analysis has been performed, where the channel dimensions produce Knudsen number values in the range 0.001–0.1, as suggested in the literature. The liquid film thickness along the flow direction is determined utilizing mass conservation, and the velocity distributions at different locations along the flow direction are obtained by solving the governing differential equations numerically. The two phase pressure drop is calculated for cases demanding slip and no slip conditions. A comparison has been made of the fluid flow characteristics, between the slip and no slip cases for the cases where slip flow is expected. The effects of the imposed heat flux, volume flow rate and channel geometry on the velocity distribution and pressure drop are examined. The predicted pressure drop values are found to increase with increasing heat flux, and decrease with an increase in the flow rate and the channel height. The two phase heat transfer coefficient and the wall temperature of the channel are also determined. The two phase heat transfer coefficient is found to increase with an increase in the vapor quality. It is also noticed that the wall temperature decreases along the length of the channel and the wall temperature at the exit of the channel decreases with decrease in volume flow rate, within the range of parameters used, which is in accordance with observations reported in the literature. The results are found to be in good agreement with the experimental and theoretical results available in the literature.

Aspect Ratio Effects on the Noncracking and Cracking Heat Transfer in Microchannels

Flow and Heat Transfer Characteristics in a Microchannel with a Circular Synthetic Jet

Numerical study of the effects of nanorod aspect ratio on Poiseuille flow and convective heat transfer in a circular minichannel

Experimental study on flow boiling heat transfer in open copper microchannel heat sinks with different aspect ratios

Study of Heat Transfer of Cryogenic Methane under Supercritical Pressure with Consideration of Thermal Conduction in Engine Cooling Channel Walls

Using Direct Simulation Monte Carlo with Improved Boundary Conditions for Heat and Mass Transfer in Microchannels

Regulation Mechanism of Microribs on Heat Transfer Process of Cracking Reactive Flow With Strong Thermal Stratification

Supercritical Heat Transfer of Cryogenic-Propellant Methane in Rectangular Engine Cooling Channels

A thermal performance factor for evaluation of active engine cooling with asymmetric heating

Numerical Investigation of the Thermal-Mechanical Behaviors in the Regenerative Cooling Channel Considering Thermal Pyrolysis

Numerical Study of Conjugate Heat Transfer of Cryogenic Methane in Rectangular Engine Cooling Channels at Supercritical Pressures

On Numerical Simulation Techniques of Stable Crack Growth

Effects of Heat Flux, Mass Flux, Inlet Fluid Subcooling, and Channel Orientation on Subcooled Flow Boiling in a High-Aspect-Ratio Rectangular Microchannel

Effect of aspect ratio on flow boiling characteristics in microchannels

Numerical Study on Thermal Cracking Process of Kerosene in a Rectangular Cooling Channel

Investigation on heat transfer during transpiration cooling with hydrocarbon fuel coolant

Thermal response time characteristics of endothermic hydrocarbon fuel in cooling channels with thermal cracking

Bubble behaviors and flow boiling characteristics in open microchannels with large aspect ratio

Subcooled flow boiling in ultrahigh-aspect-ratio microchannels for high heat flux cooling

Experimental investigation of heat transfer in flat plates with rectangular microchannels

Using Improved Dsmc Method in Simulating for the Heat and Mass Transfer in Microchannels