A Highly Efficient and Stable Perovskite Cathode with in Situ Exsolved NiFe Alloy Nanoparticles for CO2 Electrolysis

Mengmeng Wang,Naizhi Li,Qing Shen,Zhongliang Zhan,Chusheng Chen

DOI: https://doi.org/10.1039/d2se00225f

IF: 6.813

2022-01-01

Sustainable Energy & Fuels

Abstract:This study aims at improving the CO2 electrolysis performance of the lanthanum chromium ferrite cathode through modification with in situ exsolved metal nanoparticle catalysts.

What problem does this paper attempt to address?

A highly efficient and stable perovskite cathode with in situ exsolved NiFe alloy nanoparticles for CO 2 electrolysis

Mengmeng Wang,Naizhi Li,Qing Shen,Zhongliang Zhan,Chusheng Chen

DOI: https://doi.org/10.1039/d2se00225f

2022-01-01

Abstract:This study aims at improving the CO 2 electrolysis performance of the lanthanum chromium ferrite cathode through modification with in situ exsolved metal nanoparticle catalysts.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Iron-triggered Exsolution of FeNi Alloy Nanoparticles Via Topotactic Cation Exchange on Pr0.7Sr0.3Cr0.9Ni0.1O3−δ Perovskite for CO2 Electrolysis

Houfu Lv,Shuo Wang,Yuxiang Shen,Xiaomin Zhang,Yuefeng Song,Rongtan Li,Na Ta,Tianfu Liu,Guoxiong Wang,Xinhe Bao

DOI: https://doi.org/10.1016/j.nxener.2023.100024

2023-01-01

Next Energy

Abstract:Perovskites with in situ exsolved metal nanoparticles have been extensively studied for CO2 electrolysis in solid oxide electrolysis cell. However, exsolution process is strongly governed by the sluggish diffusion rate of cations and poor structural stability issues. Here we present a new exsolution process on redox stable Pr0.7Sr0.3Cr0.9Ni0.1O3−δ (PSCN) perovskite by topotactic exsolution. This process tends to generate host stoichiometric Pr0.7Sr0.3Cr0.9(FeNi)0.1O3−δ perovskite, triggering Ni cations segregation from the host while maintaining structural stability via supplement of Fe guest cations. The FeNi alloy nanoparticles decorated cathode showed a current density of 1.49 A cm−2 at 800 °C and 1.6 V for CO2 electrolysis, demonstrating over 62.0 % improvement compared to the primitive PSCN cathode. Experimental studies and density functional theory calculations revealed that the activity originated from the unique ability to adsorb and activate CO2 at the metal/perovskite interfaces. This cation supplement strategy may expand the frontiers in the evolution of exsolution on perovskite catalysts for CO2 utilization and other heterogeneous catalytic reactions.
In Situ Investigation of Reversible Exsolution/Dissolution of CoFe Alloy Nanoparticles in a Co‐Doped Sr2Fe1.5Mo0.5O6−δ Cathode for CO2 Electrolysis

Houfu Lv,Le Lin,Xiaomin Zhang,Yuefeng Song,Hiroaki Matsumoto,Chaobin Zeng,Na Ta,Wei Liu,Dunfeng Gao,Guoxiong Wang,Xinhe Bao

DOI: https://doi.org/10.1002/adma.201906193

IF: 29.4

2020-01-01

Advanced Materials

Abstract:Reversible exsolution and dissolution of metal nanoparticles in perovskite has been investigated as an efficient strategy to improve CO2 electrolysis performance. However, fundamental understanding with regard to the reversible exsolution and dissolution of metal nanoparticles in perovskite is still scarce. Herein, in situ exsolution and dissolution of CoFe alloy nanoparticles in Co-doped Sr2Fe1.5Mo0.5O6-delta (SFMC) revealed by in situ X-ray diffraction, scanning transmission electron microscopy, environmental scanning electron microscopy, and density functional theory calculations are reported. Under a reducing atmosphere, facile exsolution of Co promotes reduction of the Fe cation to generate CoFe alloy nanoparticles in SFMC, accompanied by structure transformation from double perovskite to layered perovskite at 800 degrees C. Under an oxidizing atmosphere, spherical CoFe alloy nanoparticles are first oxidized to flat CoFeOx nanosheets, and then dissolved into the bulk with structure evolution from layered perovskite back to double perovskite. Electrochemically, CO2 electrolysis performance can be retrieved during 12 redox cycles due to the regenerative ability of the CoFe alloy nanoparticles. The anchoring of the CoFe alloy nanoparticles in SFMC perovskite via reduction shows enhanced CO2 electrolysis performance and stability compared with the parent SFMC perovskite.
In Situ Construction of Metal/Perovskite Interfaces with Exsolved FeNi Alloy Nanoparticles for High-Temperature CO2 Electrolysis

Zichao Wu,Houfu Lv,Jingwei Li,Na Ta,Xiaomin Zhang,Guoxiong Wang,Xinhe Bao

DOI: https://doi.org/10.1021/acs.energyfuels.2c04110

IF: 4.6541

2023-01-01

Energy & Fuels

Abstract:Solid oxide electrolysis cells (SOECs) show potential applications in CO2 utilization and renewable energy resources storage due to their fast kinetics and high energy efficiency. However, the absence of active and stable electrode materials has limited the practical applications of SOECs for CO2 electrolysis. Herein, FeNi alloy nanoparticles anchored on a La0.6Sr0.4Fe0.85Ni0.05Nb0.1O3-delta (LSFNN) perovskite surface were developed by controlling appropriate in situ exsolution conditions for CO2 electrolysis. The FeNi@LSFNN-based SOEC showed current densities of 0.57 A cm-2 at 700 degrees C and 1.16 A cm-2 at 800 degrees C at 1.6 V, which are 1.39 and 1.18 times those of the pristine LSFNN-based cell, respectively. The distribution of relaxation time analysis of electrochemical impedance spectra and CO2 temperature-programmed desorption results indicate that the in situ constructed FeNi@LSFNN interfaces with abundant oxygen vacancies promote the adsorption, activation, and dissociation of CO2 molecules, thus improving the CO2 electrolysis performance of SOECs.
Promoting catalysis activity with optimizable self-generated Co-Fe alloy nanoparticles for efficient CO2 electrolysis performance upgrade

Kun Zhang,Dong Zhang,Yao Wang,Yihang Li,Cong Ren,Mingyue Ding,Tong Liu

DOI: https://doi.org/10.1007/s12274-023-5860-2

IF: 9.9

2023-07-13

Nano Research

Abstract:Stable and flexible metal nanoparticles (NPs) with regeneration ability are critical for long-term operation of solid oxide electrolysis cells (SOECs). Herein, a novel perovskite electrode with stoichiometric Pr 0.4 Sr 0.6 Co 0.125 Fe 0.75 Mo 0.125 O 3−δ (PSFCM) is synthesized and studied, which undergoes multiple redox cycles to validate its structural stability and NPs reversibility. The Co-Fe alloy has exsolved from the parent bulk under reducing atmosphere, and is capable of reincorporation into the parent oxide after re-oxidation treatment. During the redox process, we successfully manipulate the size and population density of the exsolved NPs, and find that the average particle size significantly reduces but the population density increases correspondingly. The electrode polarization resistance of the symmetric cell remains stable for 450 h, and even activates after the redox cycling, which may be attributed to the higher quantity and larger specific surface area of the regenerated Co-Fe alloy NPs. Moreover, the electrochemical performance towards carbon dioxide reduction reaction (CO 2 RR) is evaluated, and the CO 2 electrolyzer consisting of CoFe@PSCFM-Ce 0.8 Sm 0.2 O 1.9 (SDC) dual-phase electrode exhibits an excellent current density of 1.42 A·cm −2 at 1.6 V, which reaches 1.7 times higher than 0.83 A·cm −2 for the pristine PSCFM electrode. Overall, with this flexible and reversible high-performance SOEC cathode material, new options and perspectives are provided for the efficient and durable CO 2 electrolysis.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
In-situ passivation of Fe nanoparticles exsolved from perovskite cathodes through Zinc doping for CO2 electrolysis

Shuai Liu,Meiting Yang,Ruijia Xu,Xinghe Xiang,Guangming Yang,Haoran Xu,Gang Xiao,Ran Ran,Wei Zhou,Zongping Shao

DOI: https://doi.org/10.1039/d3gc03518b

IF: 9.8

2023-10-25

Green Chemistry

Abstract:Efficiently converting CO2 into value-added fuels or chemicals is a significant target for reducing CO2 emissions and achieving carbon neutrality. Solid oxide electrolysis cells (SOECs) are a device where CO2 reduction reaction (CO2RR) performs with high efficiency and fast kinetics at high temperatures. Since the CO2RR occurring at cathode side is the sluggish reaction over whole electrode reactions, it is crucial to develop innovative cathode materials with highly activity and good durability. Here, we demonstrate a strategy to synergistically optimize the Sr2Fe1.5Mo0.5O6–δ (SFM) bulk properties and the morphology of the exsolved nanoparticles (NPs) to enhance the CO2RR activity, electrochemical performance, and durability. The partial replacement with zinc in Fe-site of SFM not only increases the oxygen vacancy concentration of perovskite bulk and improves the CO2 adsorption capacity, but also passivates in-situ exsolution of Fe NPs and improves the active sites on perovskites surface, thus enhancing CO2 electrolysis performance. A novel cathode, Sr2Fe1.4Zn0.1Mo0.5O6–δ (SFZM01), used in a La0.8Sr0.2Ga0.8Mg0.2O3–δ electrolyte-supported single cell, shows a high current density of 2.74 A cm-2 at 850 °C (1.6 V) and excellent durability when operated at a current density of –1.0 A cm-2 at 750 °C. These findings can guide the developments of high-activity and stability catalysts for carbon capture and utilization.

chemistry, multidisciplinary,green & sustainable science & technology
Advanced Electrochemical System for Energy Storage Through CO2 Conversion

Jiawei Zhang,Wenping Li,Bowen Zhang,Minrui Gao,Chenyu Xu,Nanqi Duan,Jing-Li Luo

DOI: https://doi.org/10.1149/ma2020-01361468mtgabs

2020-01-01

ECS Meeting Abstracts

Abstract:The extensive usage of fossil fuel as energy source has led to the increased atmospheric concentration of CO2, which is mainly responsible for the negatively intensified greenhouse effect upon our living habitat. Various pathways have been studied in order to alleviate the negative effects of CO2 emission; electrochemical reduction of CO2 is considered as one of the promising method to effectively reduce CO2 emission. The process involves the conversion of CO2 to useful chemicals and fuels using high temperature solid oxide electrolysis cells (SOECs), these devices can run in the opposite direction in solid oxide fuel cells but utilize similar concepts, and involve materials challenges and operating conditions to achieve ‘Power to Fuels’. It is well known that CO2 molecules are very stable so that high energy input is required for cathodic reaction to proceed. The cathodic reaction, therefore, plays a vital role in the overall cell performance and so far, extensive investigations have been conducted to develop the advanced cathode materials with high catalytic activity and stability. Among various types of catalysts for SOECs, perovskite-based materials have attracted world wide research efforts as the mixed ionic and electronic conductors through introducing proper doping elements into perovskite lattice during synthesis process. Nonetheless, the cathodic material thus developed still suffer from relatively lower catalytic activity compared to conventional nickel-based cermets. In this work, three strategies are adopted to improve their performance of CO2 electrochemical reduction. It has been demonstrated that the perovskites with exsolved nanoparticles anchored on the surface of matrix exhibit excellent catalytic activity in comparison with the conventional ones. As a facile in-situ process, exsolution can significantly increase the number of reaction sites by forming uniformly dispersed active nanoparticles and at the same time, can efficiently impede agglomeration of nanoparticles under high temperature. Therefore, the perovskite with exsolved nanoparticles is a promising cathode material that can enhance the overall performance of CO2 reduction in an electrochemical cell.
Perovskite Oxyfluoride Ceramic with in Situ Exsolved Ni-Fe Nanoparticles for Direct CO2 Electrolysis in Solid Oxide Electrolysis Cells.

Shaowei Zhang,Yunan Jiang,Hairui Han,Yihang Li,Changrong Xia

DOI: https://doi.org/10.1021/acsami.2c05324

IF: 9.5

2022-01-01

ACS Applied Materials & Interfaces

Abstract:Solid oxide electrolysis cell (SOEC) is a potential technique to efficiently convert CO2 greenhouse gas into valuable fuels. Thus, there is significant interest in developing highly active and stable electrocatalysts for the CO2 reduction reaction (CO2RR). Herein, a Ni and F co-doping strategy is proposed to facilitate the exsolution reaction and form a new cathode, Ni-Fe alloy nanoparticles embedded in ceramic Sr2Fe1.5Mo0.5O6-δ (SFM) doped with fluorine. F-doping and Ni-Fe exsolution enhance CO2 adsorption by a factor of 2.4 and increase the surface reaction rate constant (kchem) for CO2RR from 6.79 × 10-5 to 18.1 × 10-5 cm s-1, as well as the oxygen chemical bulk diffusion coefficient (Dchem) from 9.42 × 10-6 to 19.1 × 10-6 cm2 s-1 at 800 °C. Meanwhile, the interfacial polarization resistance (Rp) decreases by 52%, from 0.64 to 0.31 Ω cm2. At 800 °C and 1.5 V, an extremely high current density of 2.66 A cm-2 and a stability test over 140 h are achieved for direct CO2 electrolysis in the SOEC.
Enhancing Electrode Performance by Exsolved Nanoparticles: A Superior Cobalt-Free Perovskite Electrocatalyst for Solid Oxide Fuel Cells.

Guangming Yang,Wei Zhou,Meilin Liu,Zongping Shao

DOI: https://doi.org/10.1021/acsami.6b12157

IF: 9.5

2016-01-01

ACS Applied Materials & Interfaces

Abstract:The successful development of low-cost, durable electrocatalysts for oxygen reduction reaction (ORR) at intermediate temperatures is critical for broad commercialization of solid oxide fuel cells. Here, we report our findings in design, fabrication, and characterization of a cobalt-free SrFeTiNiO cathode decorated with NiO nanoparticles. Exsolved from and well bonded to the parent electrode under well-controlled conditions, the NiO nanoparticles uniformly distributed on the surface of the parent electrode greatly enhance cathode performance, demonstrating ORR activity better than that of the benchmark cobalt-based BaSrCoFeO. Further, a process for regeneration of the NiO nanoparticles was also developed to mitigate potential performance degradation due to coarsening of NiO particles under practical operating conditions. As a general approach, this exsolution-dissolution of electrocatalytically active nanoparticles on an electrode surface may be applicable to the development of other high-performance cobalt-free cathodes for fuel cells and other electrochemical systems.
Exsoluble Ni–Co Alloy Nanoparticles Anchored on a Layered Perovskite for Direct CO2 Electrolysis

Zhengrong Liu,Jun Zhou,Zilin Zhou,Qiankai Zhang,Junkai Wang,Yueyue Sun,Chaofan Yin,Zixuan Xue,Kaiteng Wang,Kai Wu

DOI: https://doi.org/10.1016/j.matlet.2024.135926

IF: 3

2024-01-01

Materials Letters

Abstract:It has never been more important to develop new technologies that can reduce CO2 emissions or convert them into useful chemical products. As solid-state electrochemical devices, solid oxide electrolysis cell (SOEC) is capable of converting CO2 efficiently and selectively into CO or, when combined with water electrolysis, producing syngas (CO and H-2). Herein, we demonstrate a novel layered perovskite oxide, reduced (La4Sr4)(0.9)Ti7.2Ni0.4Co0.4O26 (LSTNC-r), decorated by exsolved Ni-Co alloy nanoparticles for high-efficiency CO2 electrolysis. The cell renders a higher activity for electrolysis of CO2 with a current density of 1.53 A cm(-2) @2.0 V and 850 degrees C. Faradic efficiency measurement and stability test suggest that LSTNC-r are promising fuel electrodes for high-efficient CO2 electrolysis.
Enhanced Electrolysis of CO2 with Metal–Oxide Interfaces in Perovskite Cathode in Solid Oxide Electrolysis Cell

Guoliang Ma,Yihong Xu,Kui Xie

DOI: https://doi.org/10.3390/catal12121607

IF: 3.9

2022-12-09

Catalysts

Abstract:The application of solid oxide electrolysis cell in CO2 electroreduction is a hot research topic at present, but the development of low−cost catalysts with high catalytic activity has always been a challenge for this work. Herein, we use NiCu alloy nanoparticles to modify the perovskite LSCM electrode to build a metal–oxide active interface to obtain high catalytic performance. At 850 °C, 4.66 mL min−1 cm−2 CO productivity and 97.7% Faraday current efficiency were obtained. In addition, the current remained stable during the 100 h long−term test, indicating that the active interface has the dual effect of improving catalytic performance and maintaining cell durability.

chemistry, physical
A High‐Entropy Layered Perovskite Coated with In‐situ Exsolved Core‐shell CuFe@FeOx Nanoparticles for Efficient CO2 Electrolysis

Ziming Wang,Ting Tan,Ke Du,Qimeng Zhang,Meilin Liu,Chenghao Yang

DOI: https://doi.org/10.1002/adma.202312119

IF: 29.4

2023-12-14

Advanced Materials

Abstract:Solid oxide electrolysis cells (SOECs) are promising energy conversion devices capable of efficiently transforming CO2 into CO, reducing CO2 emissions, and alleviating the greenhouse effect. However, the development of a suitable cathode material remains a critical challenge. Here we report a new SOEC cathode for CO2 electrolysis consisting of high‐entropy Pr0.8Sr1.2(CuFe)0.4Mo0.2Mn0.2Nb0.2O4‐δ (HE‐PSCFMMN) layered perovskite uniformly coated with in‐situ exsolved core‐shell structured CuFe alloy@FeOx (CFA@FeO) nanoparticles. Single cells with the HE‐PSCFMMN‐CFA@FeO cathode exhibits a consistently high current density of 1.95 A cm−2 for CO2 reduction at 1.5 V while maintaining excellent stability for up to 200 h under 0.75 A cm−2 at 800 °C in pure CO2. In‐situ XPS and density functional theory (DFT) calculations confirm that the exsolution of CFA@FeO nanoparticles introduces additional oxygen vacancies within HE‐PSCFMMN substrate, acting as active reaction sites. More importantly, the abundant oxygen vacancies in FeOx shell, in contrast to conventional in‐situ exsolved nanoparticles, enable the extension of the triple‐phase boundary (TPB) from the CFA@FeO/HE‐PSCFMMN interface to the entire FeOx shell, thereby enhancing the kinetics of CO2 adsorption, dissociation, and reduction. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
In situ exsolved Fe nanoparticles enhance the catalytic performance of perovskite cathode materials in solid oxide electrolytic cells

Shiwen He,Xuewei He,Lizhen Gan

DOI: https://doi.org/10.1039/d4nj03794d

IF: 3.3

2024-10-25

New Journal of Chemistry

Abstract:Global CO2 concentrations have been reported to exceed 419.3 ppm in 2023, a 51% increase from pre-industrial levels, and emissions will reach 37.4 billion tons. The concomitant rise in global temperature resulting from the increase in atmospheric CO2 concentration is precipitating a series of unprecedented challenges to global ecosystems. The development of innovative technologies mitigating the effects of climate change is of paramount importance. The solid oxide electrolytic cell (SOEC) represents a promising avenue for future CO2 resource utilization within the context of electrocatalytic conversion technology. We have employed the exceptional electronic conductivity and redox stability of the La0.7Sr0.3CrO3-δ substrate to enhance the efficacy of the electrolysis process. A series of La0.7Sr0.3CrFeXO3-δ (LSCFX ,X = 0, 0.025, 0.05, 0.075, 0.1) were prepared by fine-tuning the iron doping at the B-site via glycine liquid phase combustion. The LSCF0.075 samples exhibited promising results in CO2 electrolysis, with a CO yield of 5.25 mL min-1cm-2 and a current efficiency of 98.12%. This represents a 4.25-fold improvement over the undoped LSC. It is noteworthy that LSCF0.075 demonstrated exceptional catalytic stability after 50 hours of continuous operation at a high temperature. The industrialization of high-temperature CO2 electrolysis technology hinges on the development of efficient and stable electrode materials. This study offers promising insights in this regard.

chemistry, multidisciplinary
Efficient electrochemical CO2 reduction reaction on a robust perovskite type cathode with in-situ exsolved Fe-Ru alloy nanocatalysts

Dong Zhang,Wenqiang Yang,Zhenbin Wang,Cong Ren,Yao Wang,Mingyue Ding,Tong Liu

DOI: https://doi.org/10.1016/j.seppur.2022.122287

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:Electrochemical carbon dioxide reduction reaction (CO2RR) via a solid oxide CO2 electrolyzer has been attracting increasing attention because it can effectively convert CO2 into high value-added chemical products and effi-ciently store the excessive electricity. However, the lack of efficient electrodes to catalyze this reaction process severely limits their practical applications. Herein, we report Ru promoted perovskite type Pr0.4Sr0.6Fe0.9-Mo0.1O3-delta with a general formula of Pr0.4Sr0.6Fe0.8Ru0.1Mo0.1O3-delta (Ru-PSFM) cathode to overcome the constraints of low current density, low Faradaic efficiency, and high overpotential of CO2RR. The cathode electrolysis current density of CO2RR at 800 degrees C and 2.0 V is considerably improved from 0.707 to 1.480 A cm-2 with an enhancement rate of 109%, while its corresponding electrode polarization resistance at 1.4 V is significantly lowered from 2.228 to 0.319 omega cm-2. Furthermore, the solid oxide CO2 electrolyzer exhibits superior stability during the operation. Distribution of relaxation times analysis results reveal that the rate-determining process, involving CO2 adsorption, dissociation, and activation on the cathode surface, is significantly activated and dramatically accelerated after Ru doping. Density function theory calculations demonstrate that the in-situ exsolved Fe-Ru alloy nanocatalyst is a more favorable site for the activation of CO2 dissociation. This work provides valuable insights into the rational design of efficient cathodes for CO2RR.
Efficient electrochemical CO2 reduction reaction on a robust perovskite type cathode with in-situ exsolved Fe-Ru alloy nanocatalysts

Dong Zhang,Wenqiang Yang,Zhenbin Wang,Cong Ren,Yao Wang,Mingyue Ding,Tong Liu

DOI: https://doi.org/10.1016/j.seppur.2022.122287

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:Electrochemical carbon dioxide reduction reaction (CO2RR) via a solid oxide CO2 electrolyzer has been attracting increasing attention because it can effectively convert CO2 into high value-added chemical products and efficiently store the excessive electricity. However, the lack of efficient electrodes to catalyze this reaction process severely limits their practical applications. Herein, we report Ru promoted perovskite type Pr0.4Sr0.6Fe0.9Mo0.1O3-δ with a general formula of Pr0.4Sr0.6Fe0.8Ru0.1Mo0.1O3-δ (Ru-PSFM) cathode to overcome the constraints of low current density, low Faradaic efficiency, and high overpotential of CO2RR. The cathode electrolysis current density of CO2RR at 800 °C and 2.0 V is considerably improved from 0.707 to 1.480 A cm−2 with an enhancement rate of 109%, while its corresponding electrode polarization resistance at 1.4 V is significantly lowered from 2.228 to 0.319 Ω cm−2. Furthermore, the solid oxide CO2 electrolyzer exhibits superior stability during the operation. Distribution of relaxation times analysis results reveal that the rate-determining process, involving CO2 adsorption, dissociation, and activation on the cathode surface, is significantly activated and dramatically accelerated after Ru doping. Density function theory calculations demonstrate that the in-situ exsolved Fe-Ru alloy nanocatalyst is a more favorable site for the activation of CO2 dissociation. This work provides valuable insights into the rational design of efficient cathodes for CO2RR.

engineering, chemical
Pt Nanoparticles Confined in a 3D Porous FeNC Matrix as Efficient Catalysts for Rechargeable Li-CO2/O2 Batteries

Peng-Fang Zhang,Hong-Ying Zhuo,Yun-Yun Dong,Yao Zhou,Yun-Wu Li,Hong-Guo Hao,Da-Cheng Li,Wen-Jing Shi,Su-Yuan Zeng,Shu-Ling Xu,Xiang-Jin Kong,Yi-Jin Wu,Jin-Sheng Zhao,Shu Zhao,Jun-Tao Li

DOI: https://doi.org/10.1021/acsami.2c18857

2023-01-18

Abstract:The cathodic product Li2CO3, due to its high decomposition potential, has hindered the practical application of rechargeable Li-CO2/O2 batteries. To overcome this bottleneck, a Pt/FeNC cathodic catalyst is fabricated by dispersing Pt nanoparticles (NPs) with a uniform size of 2.4 nm and 8.3 wt % loading amount into a porous microcube FeNC support for high-performance rechargeable Li-CO2/O2 batteries. The FeNC matrix is composed of numerous two-dimensional (2D) carbon nanosheets, which is derived from an Fe-doping zinc metal-organic framework (Zn-MOF). Importantly, using Pt/FeNC as the cathodic catalyst, the Li-CO2/O2 (VCO2/VO2 = 4:1) battery displays the lowest overpotential of 0.54 V and a long-term stability of 142 cycles, which is superior to batteries with FeNC (1.67 V, 47 cycles) and NC (1.87 V, 23 cycles) catalysts. The FeNC matrix and Pt NPs can exert a synergetic effect to decrease the decomposition potential of Li2CO3 and thus enhance the battery performance. In situ Fourier transform infrared (FTIR) spectroscopy further confirms that Li2CO3 can be completely decomposed under a low potential of 3.3 V using the Pt/FeNC catalyst. Impressively, Li2CO3 exhibits a film structure on the surface of the Pt/FeNC catalysts by scanning electron microscopy (SEM), and its size can be limited by the confined space between the carbon sheets in Pt/FeNC, which enlarges the better contacting interface. In addition, density functional theory (DFT) calculations reveal that the Pt and FeNC catalysts show a higher adsorption energy for Li2CO3 and Li2CO4 intermediates compared to the NC catalyst, and the possible discharge pathways are deeply investigated. The synergetic effect between the FeNC support and Pt active sites makes the Li-CO2/O2 battery achieve optimal performance.
In situ exsolved FeNi3 nanoparticles on nickel doped Sr2Fe1.5Mo0.5O6−δ perovskite for efficient electrochemical CO2 reduction reaction

Houfu Lv,Le Lin,Xiaomin Zhang,Dunfeng Gao,Yuefeng Song,Yingjie Zhou,Qingxue Liu,Guoxiong Wang,Xinhe Bao

DOI: https://doi.org/10.1039/c9ta03065d

IF: 11.9

2019-01-01

Journal of Materials Chemistry A

Abstract:In situ exsolved FeNi3 nanoparticles on nickel doped Sr2Fe1.5Mo0.5O6−δ perovskite greatly enhance the performance of the electrochemical CO2 reduction reaction.
FeNi alloys encapsulated with N-doped porous carbon nanotubes as highly efficient and durable CO 2 reduction electrocatalyst

Li Zhang,Bo Geng,Yang Gao,Hefei Kang,Pengfei Wang,Chunmei Liu,He Xiao,Man Zhao,Jianfeng Jia,Haishun Wu

DOI: https://doi.org/10.1016/j.cej.2023.148086

IF: 15.1

2024-01-14

Chemical Engineering Journal

Abstract:The development of highly efficient, cost-effective, and robustly stable electrocatalysts for CO 2 reduction remains a significant challenge. In this study, a promising CO 2 reduction electrocatalyst composed of nanostructured transition metal alloys (i.e., FeNi, FeCo, or CoNi) nanoparticles encapsulated on N-doped porous carbon material is reported. Among the different compositions, FeNi@N-CNTs-1100 exhibited the most efficient CO 2 ER activity and exceptional stability. It demonstrated a high CO Faradaic efficiency of over 90 % in a wide potential range (–0.47 to –0.97 V ( vs. RHE)), with a CO partial current density of 20.18 mA cm −2 at –0.97 V ( vs. RHE). Notably, it achieved a long-term stability of 35 h at –0.77 V ( vs. RHE) in an H-cell with 0.5 M KHCO 3 electrolyte. Various characterization techniques and designed experiments revealed that FeNi@N-CNTs-1100 exhibited enhanced intrinsic catalytic activity and CO selectivity due to optimized *COOH adsorption and *CO desorption compared to the other catalysts studied.

engineering, chemical, environmental
In Situ Exsolution of Quaternary Alloy Nanoparticles for CO2‐CO Mutual Conversion Using Reversible Solid Oxide Cells

Yao Luo,Dong Zhang,Tong Liu,Xu Chang,Jietao Wang,Yao Wang,Xiang‐Kui Gu,Mingyue Ding

DOI: https://doi.org/10.1002/adfm.202403922

IF: 19

2024-04-27

Advanced Functional Materials

Abstract:The medium‐entropy perovskite oxides as the fuel electrode in situ exsolve the active metal cations and form quaternary alloy nanoparticles in the reduction atmosphere. The strong binding of nanoparticles to the parent with abundant oxygen vacancy provides a strong reactive interface for the efficient and durable CO2‐CO catalytic cycle. Reversible solid oxide cell is a promising energy storage and conversion device for CO2‐CO mutual conversion, with simplified cell configuration and performance stability. One key technical challenge is the lack of catalytically active and carbon‐tolerant fuel electrodes. The other one is still a lack of the kinetics mechanism and the redox stability of the active interface. Herein, the findings of a fuel electrode composed of a Sr2Fe1.0Co0.2Ni0.2Cu0.2Mo0.4O6‐δ medium‐entropy perovskite matrix decorated with in situ exsolved Fe‐Co‐Ni‐Cu quaternary alloy nanoparticles (QA@SFO) are reported. Under a reducing atmosphere, the exsolution of the quaternary alloy is accompanied by a structural transformation from double perovskite to layered perovskite, forming an interface structure where alloy nanoparticles are strongly pinned to the substrate with abundant oxygen vacancies. Electrochemically, the highly active sites provided by the QA@SFO interface greatly enhance the kinetics of CO2‐CO mutual conversion and exhibit outstanding durability for over 300 h at 1.3 V and 800 °C. Moreover, first‐principles calculations and ab initio molecular dynamics simulations from the atomic scale further elucidate the impressive electrocatalytic activity and stability and reveal that Fe and Ni in exsolved nanoparticles enhance the electrocatalytic activity, and the strong binding of Co and Cu to the parent improves the interfacial stability.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Efficient electrochemical CO2 reduction reaction on a robust perovskite type cathode with in-situ exsolved Fe-Ru alloy nanocatalysts br

Dong Zhang,Wenqiang Yang,Zhenbin Wang,Cong Ren,Yao Wang,Mingyue Ding,Tong Liu

DOI: https://doi.org/10.1016/j.seppur.2022.122287

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:Electrochemical carbon dioxide reduction reaction (CO2RR) via a solid oxide CO2 electrolyzer has been attracting increasing attention because it can effectively convert CO2 into high value-added chemical products and efficiently store the excessive electricity. However, the lack of efficient electrodes to catalyze this reaction process severely limits their practical applications. Herein, we report Ru promoted perovskite type Pr0.4Sr0.6Fe0.9Mo0.1O3-delta with a general formula of Pr0.4Sr0.6Fe0.8Ru0.1Mo0.1O3-delta (Ru-PSFM) cathode to overcome the constraints of low current density, low Faradaic efficiency, and high overpotential of CO2RR. The cathode electrolysis current density of CO2RR at 800 degrees C and 2.0 V is considerably improved from 0.707 to 1.480 A cm-2 with an enhancement rate of 109%, while its corresponding electrode polarization resistance at 1.4 V is significantly lowered from 2.228 to 0.319 omega cm-2. Furthermore, the solid oxide CO2 electrolyzer exhibits superior stability during the operation. Distribution of relaxation times analysis results reveal that the rate-determining process, involving CO2 adsorption, dissociation, and activation on the cathode surface, is significantly activated and dramatically accelerated after Ru doping. Density function theory calculations demonstrate that the in-situ exsolved Fe-Ru alloy nanocatalyst is a more favorable site for the activation of CO2 dissociation. This work provides valuable insights into the rational design of efficient cathodes for CO2RR.

A Highly Efficient and Stable Perovskite Cathode with in Situ Exsolved NiFe Alloy Nanoparticles for CO2 Electrolysis

A highly efficient and stable perovskite cathode with in situ exsolved NiFe alloy nanoparticles for CO 2 electrolysis

Iron-triggered Exsolution of FeNi Alloy Nanoparticles Via Topotactic Cation Exchange on Pr0.7Sr0.3Cr0.9Ni0.1O3−δ Perovskite for CO2 Electrolysis

In Situ Investigation of Reversible Exsolution/Dissolution of CoFe Alloy Nanoparticles in a Co‐Doped Sr2Fe1.5Mo0.5O6−δ Cathode for CO2 Electrolysis

In Situ Construction of Metal/Perovskite Interfaces with Exsolved FeNi Alloy Nanoparticles for High-Temperature CO2 Electrolysis

Promoting catalysis activity with optimizable self-generated Co-Fe alloy nanoparticles for efficient CO2 electrolysis performance upgrade

In-situ passivation of Fe nanoparticles exsolved from perovskite cathodes through Zinc doping for CO2 electrolysis

Advanced Electrochemical System for Energy Storage Through CO2 Conversion

Perovskite Oxyfluoride Ceramic with in Situ Exsolved Ni-Fe Nanoparticles for Direct CO2 Electrolysis in Solid Oxide Electrolysis Cells.

Enhancing Electrode Performance by Exsolved Nanoparticles: A Superior Cobalt-Free Perovskite Electrocatalyst for Solid Oxide Fuel Cells.

Exsoluble Ni–Co Alloy Nanoparticles Anchored on a Layered Perovskite for Direct CO2 Electrolysis

Enhanced Electrolysis of CO2 with Metal–Oxide Interfaces in Perovskite Cathode in Solid Oxide Electrolysis Cell

A High‐Entropy Layered Perovskite Coated with In‐situ Exsolved Core‐shell CuFe@FeOx Nanoparticles for Efficient CO2 Electrolysis

In situ exsolved Fe nanoparticles enhance the catalytic performance of perovskite cathode materials in solid oxide electrolytic cells

Efficient electrochemical CO2 reduction reaction on a robust perovskite type cathode with<i> in</i><i>-situ</i> exsolved Fe-Ru alloy nanocatalysts

Efficient electrochemical CO2 reduction reaction on a robust perovskite type cathode with in-situ exsolved Fe-Ru alloy nanocatalysts

Pt Nanoparticles Confined in a 3D Porous FeNC Matrix as Efficient Catalysts for Rechargeable Li-CO2/O2 Batteries

<i>In situ</i> exsolved FeNi<sub>3</sub> nanoparticles on nickel doped Sr<sub>2</sub>Fe<sub>1.5</sub>Mo<sub>0.5</sub>O<sub>6−δ</sub> perovskite for efficient electrochemical CO<sub>2</sub> reduction reaction

FeNi alloys encapsulated with N-doped porous carbon nanotubes as highly efficient and durable CO 2 reduction electrocatalyst

In Situ Exsolution of Quaternary Alloy Nanoparticles for CO2‐CO Mutual Conversion Using Reversible Solid Oxide Cells

Efficient electrochemical CO<sub>2</sub> reduction reaction on a robust perovskite type cathode with <i>in</i>-<i>situ</i> exsolved Fe-Ru alloy nanocatalysts br