Abstract:In the present paper, cracking sequence of high-strength engineered cementitious composite with the characteristic of low drying shrinkage (LSECC) under tension was experimentally studied by continually photographing during loading. The specific objective is to investigate the development of crack opening of each individual crack occurred during loading. Four Engineered cementations composite mixtures with water to binder ratio of 0.20, 0.25, 0.30, and 0.35 (LSECC-0.20, LSECC-0.25, LSECC-0.30, and LSECC-0.35) were used in the tests. Using the photographers taken during the test, crack width of each crack occurred during loading are determined according to the difference between solid material and crack on gray level. The test results show that cracks in ECC under tensile load are formed according to a temporal sequence. The opening width of each crack grows in a controllable and gradual manner with the increase of tensile strain. At a given strain level, crack width of different crack is not equal and the distribution of crack width is affected by matrix strength of the composite. Maximum crack width and the tensile strain capacity at the moment may be utilized to characterize the tensile performance of the composite that can guarantee both of tensile ductility and long-term durability. As maximum crack width equals 60 μm, at which the permeability of ECC may not be influenced by the cracks, higher strength ECC with water to binder ratio of 0.20 and 0.25 (LSECC-0.20 and LSECC-0.25) shows obvious higher tensile strain capacity and more cracks of narrow opening. By contrast, lower strength ECC with water to binder ratio of 0.30 and 0.35 (LSECC-0.30 and LSECC-0.35) shows relatively lower tensile strain and fewer cracks of narrow crack opening as crack width is limited below 60 μm. With the increase of tensile strain and the maximum crack width, much wider cracks (larger than 60 μm) are formed in lower strength ECC comparing to that of higher strength ECC.

Engineered Cementitious Composites Using Chinese Local Ingredients: Material Preparation and Numerical Investigation

Compressive Behavior of Engineered Cementitious Composites under High Strain-Rate Loading

Multiscale Investigation on the Performance of Engineered Cementitious Composites Incorporating PE Fiber and Limstone Calcined Clay Cement (LC3)

Development of Sustainable Engineered Cementitious Composites by Incorporating Local Recycled Fine Aggregate

Preliminary Analysis of the Ductility and Crack-Control Ability of Engineered Cementitious Composite with Superfine Sand and Polypropylene Fiber (SSPP-ECC)

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

Investigation of the Mechanical Properties of Engineered Cementitious Composites with Low Fiber Content and with Crumb Rubber and High Fly Ash Content

Durability Performance Investigation for Engineering Fiber Cementitious Composites (ECC): Review

Compression and Flexural Behavior of ECC Containing PVA Fiber

Evaluation of the Performance of Engineered Cementitious Composites (ECC) Produced from Local Materials

Optimisation of the Mechanical Properties and Mix Proportion of Multiscale-Fibre-Reinforced Engineered Cementitious Composites

Axial Compressive Behavior of Engineered Cementitious Composite Confined by Fiber-Reinforced Polymer

Fiber-Bridging Constitutive Law of Engineered Cementitious Composites

An Experimental and Analytical Study on a Damage Constitutive Model of Engineered Cementitious Composites under Uniaxial Tension

Experimental investigation on seismic performance of plain engineered cementitious composite beams

Uniaxial Tensile Experiment On Pva Fiber Reinforced Cementitious Composites

Mapping of cracking sequence of polyvinyl alcohol-steel hybrid fiber reinforced high-strength engineered cementitious composite under uniaxial tension

Ultra-low carbon lightweight engineered cementitious composite: Design and material characterization

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling

Greener Engineered Cementitious Composite (ECC) – the Use of Pozzolanic Fillers and Unoiled PVA Fibers

Stress–strain Behaviour of Hybrid-Fibre Engineered Cementitious Composite in Compression