Abstract:The manifold microchannel heat sink (MMCHS) is a promising design for heat dissipation in high power electronics. However, the configuration of the microchannels in MMCHS is generally rectangular straight channels, which would limit the further improvement of heat transfer performance. Topology optimiza-tion has been proven to be an effective approach to design single-phase heat sinks, which only depends on the iterative algorithm. In this work, we first design three single-phase heat transfer structures (2D) by a density-based topology optimization method, and then systematically investigate the two-phase flow and heat transfer characteristics of MMCHS (3D configurations that are converted based on 2D designs). The thermohydraulic performances of three topologically optimized MMCHS obtained by varying the con-strained pressure drop (named TOC-I, TOC-II and TOC-III for simplicity) and the baseline rectangular MM-CHS are compared. The results show that the flow paths in the TOCs exhibit root-like configurations and the number of pin fins increases with the increase in constrained pressure drop (i.e., TOC-III has the most complex flow path). Due to the differences in velocity distribution and channel width among various con -figurations, churn flow and confined bubbly flow are observed in BC and TOCs, respectively. Compared to BC, the maximum average heat transfer coefficients of TOC-I, TOC-II and TOC-III are increased by 40%, 62% and 87%, respectively. The TOC-I has the lowest pressure drop due to the minimum number of pin fins and the relatively large channel width. The maximum values of Figure of Merit (FOM), a parameter usually employed to analyze the comprehensive performance of MMCHS, for TOC-I, TOC-II and TOC-III are 1.72, 1.77 and 1.8 at Qb= 10 0 0 W/cm2, respectively. Moreover, TOC-I and TOC-III have the best compre-hensive performance at 300 W/cm2 <= Qb <= 800 W/cm2 and 900 W/cm2 <= Qb <= 10 0 0 W/cm2, respectively.(c) 2023 Elsevier Ltd. All rights reserved.

Mmc-Based Heat Sink Topology Optimization Design for Natural Convection Problems

Nature Convection Heatsink Modeling and Optimization Based on Nusselt Number Correlation

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Topology optimization of heat sinks for instantaneous chip cooling using a transient pseudo-3D thermofluid model

Sobol sensitivity analysis and multi-objective optimization of manifold microchannel heat sink considering entropy generation minimization

Topology Optimization of Turbulent Forced Convective Heat Sinks Using a Multi-Layer Thermofluid Model

Design of Microchannel Heat Sink Using Topology Optimization for High Power Modules Cooling

Topology optimization of heat sink based on variable density method

Three-dimensional Multi-Scale Topology Optimization of Porous Heat Sink with Predetermined Unit Cells for Natural Convection Heat Transfer

Concurrent optimization of the internal flow channel, inlets, and outlets in forced convection heat sinks

Three-dimensional Topology Optimization of Natural Convection Using Double Multiple-Relaxation-time Lattice Boltzmann Method

Topology Optimization of Microchannel Heat Sinks Using a Two-Layer Model

Multi-objective Optimal Design of Microchannel Cooling Heat Sink Using Topology Optimization Method

Heat Dissipation Design Based On Topology Optimization And Auxiliary Materials

Investigation of the Parameter-Dependence of Topology-Optimized Heat Sinks in Natural Convection

Topology Optimization of Planar Heat Sinks Considering Out-of-plane Design-Dependent Deformation Problems

Heat Transfer Augmentation in Microchannel Heat Sink Based on Isogeometric Topology Optimization Framework

Multi-objective Bayesian topology optimization of a lattice-structured heat sink in natural convection

Three-dimensional topology optimization of thermal-fluid-structural problems for cooling system design

Optimization of Bionic Heat Sinks with Self-Organized Structures Inspired by Termite Nest Morphologies

Micro Pin Fins with Topologically Optimized Configurations Enhance Flow Boiling Heat Transfer in Manifold Microchannel Heat Sinks