Abstract:The slow-cooling treatment has been observed to induce the formation of serrated grain boundaries, which effectively enhance the creep strength of nickel-based powder superalloys. However, this heat treatment also leads to the coarsening of γ′ precipitates in nickel-based alloys, which impairs their dispersion-strengthening effects. To address this issue, the high-temperature pre-precipitation treatment (HTPT) was employed to simultaneously form fine γ′ precipitates and serrated grain boundaries in the alloys. A systematic investigation was conducted to analyze the impact of various HTPT intermediate temperatures (ranging from 1150 to 1110 °C) on the microstructure and mechanical properties of the superalloy. In this study, a significant increase in the volume fraction of secondary γ′ with a butterfly-shaped morphology, from 1.6% to 27.7%, was observed as the intermediate temperature was decreased from 1150 to 1110 °C. Simultaneously, the average size of spherical tertiary γ′ precipitates decreased from 73.3 nm to 52.7 nm. Serrated grain boundaries were observed in the samples when the HTPT temperature was below 1140 °C, with increasing amplitudes ranging from 2.1 to 2.8 μm. To investigate the formation mechanism of these serrated grain boundaries, we focused on the interactions between γ′ precipitates and grain boundaries. At temperatures below 1135 °C, a fan-shaped structure consisting of finger-shaped γ′ dendrites and γ phases was observed, which potentially contributes to the formation of serrated grain boundaries. Among the samples tested, the sample subjected to an HTPT temperature of 1130 °C showed the best mechanical properties at room temperature (1542 MPa, 12.9% elongation), while the 1140 °C sample exhibited superior performance at 750 °C (1301 MPa, 6.5% elongation). These findings highlight the potential of heat treatment as a novel approach for enhancing the mechanical characteristics of nickel-based superalloys.

Effect of Gradient Microstructure on Elevated Temperature Mechanical Properties of Ni-based Superalloy ATI 718Plus

Effect of a gradient structure on the mechanical performance of Inconel 718 Ni-based superalloy at elevated temperatures

Effect of Δ Phase and Grain Gradient Microstructure on Elevated-Temperature Mechanical Performances of the Gh4169 Alloy

Effect of Annealing Treatment on Microstructure Evolution and Creep Behavior of a Multiphase Ni3Al-based Superalloy

Effect of the precipitation of the η-Ni3Al0.5Nb0.5 phase on the microstructure and mechanical properties of ATI 718Plus

Influences of the Γ′ Phase on the Mechanical Properties of a Nickel-Based Single Crystal Superalloy

Preparing Gradient Microstructure to Achieve Enhanced Performance in GH4586 Superalloy: Experiments and Models

Effect of Solution Cooling Rate on Microstructure Evolution and Mechanical Properties of Ni-based Superalloy ATI 718Plus

Enhancing tensile properties of wrought Ni-based superalloy ATI 718Plus at elevated temperature via morphology control of η phase

Designing a gradient structure in a Ni-based superalloy to improve fretting fatigue resistance at elevated temperatures through an ultrasonic surface rolling process

Precipitates Evolution and Tensile Behavior of Wrought Ni-based ATI 718plus Superalloy During Long-Term Thermal Exposure

Strengthening Effects and Thermal Stability of the Ultrafine Grained Microstructure of a Nickel Base Superalloy at Room and Elevated Temperatures

Microstructures and Tensile Properties of a Grain-size Gradient Nickel-based Superalloy

Effect Of Gradient Microstructure Pinned By 6 Phase On Elevated Temperature Performances Of Gh4169

The Effect of Nb, Ti, Al on Precipitation and Strengthening Behavior of 718 Type Superalloys

Effects of pre-precipitation treatment temperature on the microstructure and mechanical properties of nickel-based powder superalloy

Tailoring the Microstructure and Deformation Mechanisms of an Additively Manufactured Nickel-Based Superalloy by Post-Aging Heat Treatment

Influence of Heat Treatment on Microstructure and Tensile Behavior of A Hot Isostatically Pressed Nickel-Based Superalloy

Effect of Heat Treatment on the Mechanical Property and Deformation Mechanism of a Novel Cast Nickel-Based Superalloy

Suppression of Texture and Enhancement of High-Temperature Tensile Property in Heavily Deformed Gradient Ti2AlNb Alloy

Effects of the γ″-Ni3Nb Phase on Mechanical Properties of Inconel 718 Superalloys with Different Heat Treatments