Abstract:Ceramic-based nanocomposite membranes are gaining great attention in various applications, such as water treatment; gas separation; oil and gas, amid their superior fouling resistance and remarkable chemical/thermal stability. Here, we report for the first time the use of spark plasma sintering (SPS) process to fabricate a porous alumina-carbon nanotubes (Al2O3-CNT) nanocomposite membrane for water treatment. The challenge is this work is to achieve a balance between the amount of porosity, desired for a high water flux, and the membrane strength level, required to resist the applied pressure during a water flow experiment. The effect of SPS process parameters (pressure, temperature, heating rate, and holding time) on the microstructure and properties of the developed membrane was investigated and correlated. A powder mixture composed of Al2O3 and 5 wt % CNT was prepared with the addition of starch as a pore former and gum Arabic and sodium dodecyl sulfate as dispersants. The powder mixture was then sintered using SPS to produce a solid but porous nanocomposite membrane. The structure and microstructure of the developed membrane were characterized using X-ray diffraction and field emission scanning electron microscopy. The performance of the membrane was assessed in terms of porosity, permeability, and mechanical properties. Moreover, the adsorption capability of the membrane was performed by evaluating its removal efficacy for cadmium (II) from water. The microstructural analysis revealed that CNT were distributed within the alumina matrix and located mainly along the grain boundaries. The permeability and strength were highly influenced by the sintering pressure and temperature, respectively. The results indicated that the membrane sintered at a pressure of 10 MPa, temperature of 1100 °C, holding time of 5 min, and heating rate of 200 °C/min exhibited the best combination of permeability and strength. This developed membrane showed a significant removal efficiency of 97% for cadmium (II) in an aqueous solution.

One-step dip-coating method for preparation of ceramic nanofiber membrane with high permeability and low cost

Fabrication of Catalytic Ceramic Nanofiber Membrane with High Permeability and Superior Catalytic Performance

Preparation of a High-Performance Porous Ceramic Membrane by a Two-Step Coating Method and One-Step Sintering

Preparation and Application of Flat-Plate Ceramic Ultrafiltration Membrane with High-Performance by Spray-Dip Coating Method

Preparation of Ceramic Ultrafiltration Membrane by Nano-Metal Oxides Modified

Compact SiOC Ceramic Composite Nanofiltration Membranes by Slow Dip Coating for Water Purification

Ceramic nanofiber membrane anchoring nanosized Mn<sub>2</sub>O<sub>3</sub> catalytic ozonation of sulfamethoxazole in water

Polyamide/PVC Based Composite Hollow Fiber Nanofiltration Membranes: Effect of Substrate on Properties and Performance

Asymmetric alumina-based ultrathin composite ceramic membranes with interfacial modification of black talc nanosheets

One-step fabrication of asymmetric alumina ceramic membranes with tunable pore parameters for oil-water separation

A novel ceramic-based thin-film composite nanofiltration membrane with enhanced performance and regeneration potential

One-step pasting method for preparation of flat-sheet ceramic membrane

Fabrication and characterization of low cost tubular mineral-based ceramic membranes for micro-filtration from natural zeolite

Melded Ceramic Membranes: A Novel Fabrication Method for Ultrathin Alumina Membranes of High Performance

Preparation of high permeance thin-film composite nanofiltration membrane on macroporous ceramic support

High-flux ceramic membrane derived from UV-curable slurry for efficient separation of nanoparticles suspension

Novel Fabrication Processing of Porous Al2O3/CaAl12O19 Membrane by Combining Emulsion, Cement Curing and Tape-Casting Methods

One Step Co-Sintering Synthesis of Gradient Ceramic Microfiltration Membrane with Mullite/alumina Whisker Bi-Layer for High Permeability Oil-in-water Emulsion Treatment

Fabrication and assessment of performance of clay based ceramic membranes impregnated with CNTs in dye removal

An effective method for improving the permeation flux of a ceramic membrane: Single-matrix spherical ceramic membrane

Porous Al2O3-CNT Nanocomposite Membrane Produced by Spark Plasma Sintering with Tailored Microstructure and Properties for Water Treatment