Abstract:NHR200-II is a 200 MW nuclear heating reactor. The integrity of the fuel assembly should be ensured during the normal operations and design basis accidents. In the latter cases (e.g. earthquake), its deformation or damage should not prevent the insertion of control rods to shut down the reactor. Meanwhile, during the operating time, there are two aspects that attention should be paid, (i) the mechanical performance of internal core materials might be worsened by the increase of burnup and (ii) dynamic loads involving hydraulic erosion, flow-induced vibration might damage the assemblies. Therefore, the investigation of the dynamic characteristics of the fuel assembly with consideration of burnup effects is necessary. The fuel rod with pellets and cladding was approximated by the beam elements with a circular cross-section applied with calibrated material properties. Connector elements were used to replace the three-arc springs and dimples on the grid and thus simplify the geometry of the spacer grid. The agreements between the detailed and simplified models indicate the equivalence of these two methods. Then two simulations were performed to evaluate the dynamic characteristics of NHR200-II fuel assembly at the beginning of life. The modal simulation of the fuel bundle and channel suggests that the channel could be assumed stationary to the fuel bundle during the dynamic analysis. The seismic simulation conducted in the specific boundary conditions indicates that the integrity of spacer grids can be guaranteed and there was no buckling of the gird. No permanent deformation of the channel was observed, and its relative displacements were sufficiently small to ensure the insertion of control rods. Finally, burnup effects on the structural behavior of the fuel rod are discussed. The initial conditions of NHR200-II fuel assembly and its material properties at different burnup times are provided by referring to two irradiated tests. Various sensitivity analyses had been conducted to evaluate the effects of material properties and pellet-cladding interaction on the resulting failure limit and stiffness of the fuel rod.

Development of 3-D Numerical Methodology to Investigate Transient Characteristics of Fuel Temperature and Hydrated Residual Water During Drying Process of Dry Storage System

Investigating the Natural Convection Behavior in the Transportable Storage Canister of Dry Storage Systems Through CFD Simulation

Development of 3-D CFD Methodology to Investigate the Transient Thermal-Hydraulic Characteristics of Coolant in a Spent Fuel Pool

Numerical Investigation of Passive Thermal-Hydraulic Performance of Spent Fuel Dry-Storage System for HTR-PM

CFD Simulating the Transient Thermal–hydraulic Characteristics in a 17 × 17 Bundle for a Spent Fuel Pool under the Loss of External Cooling System Accident

Applicability of differential die-away self-interrogation technique for quantification of spontaneous fission nuclides for fuel debris at Fukushima Daiichi Nuclear Power Plants

Development of a thermal-hydraulic analysis code TAC-DS for spent fuel dry-storage system for high-temperature pebble bed reactor

Thermal Analysis on NAC-STC Spent Fuel Transport Cask under Different Transport Conditions

ANALYSIS OF HEAT TRANSFER ON SPENT FUEL DRY CASK DURING SHORT-TERM OPERATIONS

Conceptual Design, Development, and Preliminary Safety Evaluation of a PWR Dry Storage Module for Spent Nuclear Fuel

A numerical method for simulating the non-homogeneous irradiation effects in full-sized dispersion nuclear fuel plates

SPECIFIC FEATURES OF NUMERICAL SIMULATION OF THERMAL OPERATION MODE THE SPENT FUEL POOLS OF BILIBINO NPP

Modeling of irradiation-induced thermo-mechanical coupling behavior in metal matrix microencapsulated fuel

Simulation of Dynamic Characteristics of NHR200-II Fuel Assembly

Numerical Simulation and Investigation on Natural Circulation Cooling Transient Process for Spent Fuel Assembly in Sodium-cooled Fast Reactor

Thermal-fluid-structure Coupling Analysis for Plate-Type Fuel Assembly under Irradiation. Part-I Numerical Methodology

Study on the mass and heat transfer characteristics of the drying process of spent nuclear fuel cladding with nitrogen assisted

Simulation of the Irradiation-Induced Micro-Thermo-Mechanical Behaviors Evolution in Ads Nuclear Fuel Pellets

Numerical Simulation Research on the Irradiation-Thermal-Mechanical Performance Evolution of FCM Fuel

3-Dimensional Multiphysics Modeling of Behaviors of Pressurized Water Reactor Fuel Rods With Missing Pellet Surface

Numerical simulation of the irradiation-mechanical behaviors of dispersion nuclear fuel elements