Abstract:154-km long tunnels of major highways in Shanxi Province of China are observed, and 5,120 crack distributions are obtained that are largely dependent on both earth pressure conditions and external water pressure. By conducting 1:30 scaled model tests, the cracking patterns of the mold lining induced by earth pressure are notably different from those induced by external water pressure. Under high external water pressure, moment-induced tensile failure occurs at the knee of the tunnel lining, and then flexural failure appears at the invert. Increasing the earth pressure can rapidly decrease the bending moment, moderately increase the axial thrust, and considerably enhance the structural safety of the tunnel lining provided that the earth pressure is less than 0.3MPa. The ultimate water pressure, influenced by earth pressure, increases by approximately 17 %, regardless of the ratio of horizontal to vertical stresses K. For a tunnel under high earth pressure, the upper parts of the tunnel lining are the locations most susceptible to failure, whereas the invert is safe with a large safety margin. Imposing external water pressure could substantially increase both the axial thrust along with the bending moment and suddenly worsen the structural soundness of the tunnel lining. Furthermore, the failure positions and cracking sequences are highly correlated with the values of K. These findings are supported by three-dimensional nonlinear finite element numerical modeling. Finally, the interaction of water pressure and earth pressure conditions is investigated under various ratios of horizontal to vertical stresses K in the ultimate limit state.

What problem does this paper attempt to address?

The problems that this paper attempts to solve are as follows: 1. **Behavior patterns of tunnel linings under earth pressure and external water pressure**: Through on - site observations and 1:30 - scale model tests, the paper studied the crack distribution and failure patterns of tunnel linings under different earth pressure conditions (especially the ratio K of horizontal to vertical earth pressure) and external water pressure. Specifically, the author focused on how these factors affect the mechanical response of tunnel linings, especially the safety and stability of tunnel linings under high groundwater level conditions. 2. **Influence of different pressure types on the failure location of tunnel linings**: The paper explored the influence of external water pressure and earth pressure with different K values on the failure patterns of tunnel linings. The study found that external water pressure mainly leads to bending failures at the bottom (inverted arch) and knee parts of the tunnel, while earth pressure mainly causes failures in the upper part of the tunnel (such as the roof and shoulders). 3. **Optimization of tunnel lining design parameters**: Based on the above research results, the paper put forward some suggestions for optimizing tunnel lining design to improve its safety and reliability under specific geological conditions. These suggestions help designers take effective preventive measures before construction to reduce or avoid the destruction of tunnel linings. 4. **Numerical simulation verification**: In order to further verify the experimental results, the author used the nonlinear finite - element numerical simulation method for analysis to ensure the accuracy and reliability of the experimental results. In summary, the main purpose of this paper is to deeply understand the mechanical behavior of tunnel linings under complex pressure conditions through experiments and numerical simulations, thereby providing a scientific basis for the design and construction of tunnel projects.

Model test on the behavior of tunnel linings under earth pressure conditions and external water pressure

INTERACTION OF SURROUNDING ROCK OR SOIL AND LINING OF A PRESSURE TUNNEL

Observed response of a shield-driven tunnel to fluctuations in river stage

Earth Pressure and Internal Forces of Tunnel Lining in Jet Grouting Reinforced Mud Stratum

A novel method of imposing external water pressure to explore the failure behavior of railway tunnel linings

Model Test Studies on Ground Subsidence and Cracks Induced by Tunneling in Weak Rock Mass with High Water Content

Experimental Study on Deformation Properties of Lining Structure of Hydraulic Tunnel

Numerical Simulation of Highway Tunnel Composite Lining Temperature Stress

Three-dimensional Numerical Modeling of Water Distribution Tunnels in Karst Area

Experimental Study on the Carrying Capacity of Lining Structure of Hydraulic Tunnel

Influence of cracks at the invert on the mechanical behavior of the tunnel structures

Experimental and numerical investigation on cracking mechanism of tunnel lining under bias pressure

Structural Stability Monitoring of Model Test on Highway Tunnel with Lining Backside Voids Using Dynamic and Static Strain Testing Sensors

Geo-mechanical model test on excavation and support of deep tunnel crossing a fault under hydro-mechanical coupled condition

Effects of long-term leakage of shield lining on tunnelling-induced ground consolidation movements

Mechanical behaviors of surrounding rock and supporting structure of shallow-buried unsymmetrical pressure tunnel crossing soil–rock interface

Experimental and numerical study of the failure mechanism and stability of tunnel linings under different cavity conditions

Study on cracking behavior of tunnel linings with the diseases of void and lining insufficient thickness

Cracking characteristics and mechanism of entrance section in asymmetrically-load tunnel with bedded rock mass: A case study of a highway tunnel in southwest China

Modelling the hydro-mechanical behaviour of high-pressure tunnel with emphasis on the interaction between lining and rock mass

Cracking performance of asymmetric double-arch tunnels due to the voids behind linings