Abstract:It is very important to prepare high sensitive surface enhanced Raman scattering (SERS) substrates in the SERS detection process. The preparation of metal nanoparticle aggregates by light manipulation technology is a hot topic in the field of SERS. In this paper, femtosecond laser wet etching technology was used to etch slot array with the cross-sectional area (width x depth) of 10 mu m x 7 mu m, 30 mu m x 12 mu m, 60 mu m x 15 mu m, 70 mu m x 19 mu m, 90 mu m x 21 mu m in the range of 5 mm x 5 mm on the surface of silicon wafer, a Silicon-based micro-nano structure substrate (SiMS) with the different cross-sectional area was prepared. SERS enhancement of analytes on the substrates was achieved using optical manipulation techniques combined with SERS technique. The laser was focused on the substrate slot, due to the action of the light radiation pressure, the gold nanoparticles move along the direction of the beam propagation and accumulate in the slots on the surface of the structure to form gold nanoparticle aggregates, which promote "hot spots" effect. The sensitivity of the SERS detection was improved, and the SERS enhancement of the probe on the substrates was achieved. Experiments show that the metal nanoparticles can effectively accumulate in the slot on the surface of the SiMS when the optical radiation pressure is greater than the optical gradient force, forming more "hot spots", which can greatly improve the SERS enhancement effect. The SERS signal of pyrene is gradually enhanced with the increase of the cross-sectional area of the slot, the enhancement effect of the slot with width and depth of 70 x 19 mu m(2) was the best, SERS intensity of pyrene was increased by about two magnitudes, and the minimum detection concentration was 5. 0 x 10 9 mol. L-1. Beyond this cross-sectional area, the SERS intensity begins to decrease. The lowest detection concentration of pyrene is 5. 0 x 10 9 mol.L-1. In the low concentration range (5. 0 x 10(-9) similar to 1. 0 x 10 mol.L-1). It demonstrated a good linear correlation between the SERS intensity of characteristic peaks at 588 and 1 234 cm(-1) and concentration, and the fitting equation and linear correlation coefficient were 0. 992 and 0. 971, respectively. The SiMS with a cross-sectional area of 70x19 mu m(2) was used for repetitive experiments, and eight different positions on the substrate were selected. After each position was measured, the laser was switched off and the action of the laser was disappeared, the gold nanoparticles were re-dispersed in the solution. Three measures were repeated for each position. The relative standard deviation (RSD) of the two peaks at 588 and 1 234 cm(-1) at different positions of the substrate were 9. 9% and 2.0% respectively, which showed good repeatability. The study showed that the SERS effect could be greatly improved by the optical manipulation-SERS method based on the SiMS and this method has potential for application in the detection and analysis of materials in fields such as chemistry and biology.

Facile Fabrication of Ultrahigh-Sensitivity Surface-Enhanced Raman Scattering Sensor Using Porous Silicon Photonic Crystals Prepared on Backside Silicon Wafer

Porous Silicon Photonic Crystal/silver Composite Produced by Microwave-Assisted Reduction: Applications to Surface-Enhanced Raman Scattering

Extremely Sensitive SERS Sensors Based on a Femtosecond Laser-Fabricated Superhydrophobic/-philic Microporous Platform

Porous Silicon Photonic Crystals Coated With Ag Nanoparticles As Efficient Substrates For Detecting Trace Explosives Using Sers

Highly Sensitive, Uniform, and Reproducible Surface-Enhanced Raman Spectroscopy Substrate with Nanometer-Scale Quasi-periodic Nanostructures.

A Facile Method to Fabricate a Novel 3D Porous Silicon/gold Architecture for Surface Enhanced Raman Scattering

Surface-Enhanced Raman Scattering with Au Nanoparticles Optically Trapped by a Silicon-Based Micro-Nano Structure Substrate

Large-area Surface-Enhanced Raman Scattering-Active Substrates Fabricated by Femtosecond Laser Ablation

Fabrication of High-Performance Microfluidic SERS Substrates by Metal-Assisted Chemical Etching of Silicon Scratches

High-performance Flexible Surface-Enhanced Raman Scattering Substrate Based on the Particle-in-multiscale 3D Structure

Three-dimensional composite substrate based on pyramidal pitted silicon array adhered Au@Ag nanospheres for high-performance surface-enhanced Raman scattering

Surface Enhanced Raman Scattering Substrate Base On Band Gap Edge Effect Of Photonic Crystal

Flexible Large-Area Surface Enhanced Raman Scattering Substrate Based on Bowl-Shaped Arrays of Au Nanoparticles on PDMS

Improved Sensitivity of Surface-Enhanced Raman Scattering with Gold Nanoparticles-Insulator-Metal Sandwich Layers on Flat Sapphire Substrate

Fabrication of Uniform Substrate Based on Silver Nanoparticles Decorated Glycidyl Methacrylate‐ethylene Dimethacrylate Porous Material for Ultrasensitive Surface‐enhanced Raman Scattering Detection

High-performance, Large-Area Flexible SERS Substrates Prepared by Reactive Ion Etching for Molecular Detection

Flexible Surface-Enhanced Raman Scattering Chip: A Universal Platform for Real-Time Interfacial Molecular Analysis with Femtomolar Sensitivity

Preparation of SiO2@Au Nanoparticle Photonic Crystal Array as Surface-Enhanced Raman Scattering (SERS) Substrate

The Fabrication of Ag Nanostructure Array Integrated with Microfluidics for Surface Enhanced Raman Scattering

Self‐Support Surface Enhanced Raman Scattering Substrates with the Function of Enriching Analytes

Flexible Plasmonic Nanoparticle-on-a-mirror Metasurface-Enabled Substrates for High-Quality Surface-Enhanced Raman Spectroscopy Detection