Abstract:OBJECTIVE:To investigate the effect of a noval radio-frequency atmospheric-pressure glow discharge (RF-APGD) plasma jet on crosslinking of dentin collagen.METHODS:(1) Twenty intact third molars were collected. The middle dentin discs were prepared for each tooth by low-speed water-cooled Isomet saw, and then immersed in 10% (mass fraction) H3PO4 solution for 16 h to obtain fully demine-ralized dentin collagen. The twenty dentin discs were then randomly divided into five groups. The control group was untreated while the four experimental groups were treated by plasma jet with gas temperature of 4 ℃ for different times (20 s, 30 s, 40 s, and 50 s). The structure and crosslinking degree of dentin collagen were characterized by attenuated total reflection-Fourier transform infrared spectroscopy. The surface morphology of demineralized dentin was observed by scanning electron microscope, and the microstructure was observed by transmission electron microscope. (2) Fourty non-caries third molars were collected to prepare 5 g fine dentin powder, then completely demineralized with 10% H3PO4 solution. The control group was untreated, while the four experimental groups were treated by plasma jet for 20 s, 30 s, 40 s and 50 s. The crosslinking degree of each group was determined by ninhydrin colorimetric method. (3) Forty intact third molars were collected to obtain dentin strips. Only two central symmetrical dentin strips (nasty 80) were taken from each tooth and immersed in 10% H3PO4 solution for 16 h to obtain fully demineralized dentin collagen. Eighty dentine collagen fiber strips were randomly divided into five groups. The control group was untreated and the axial surfaces of dentin collagen fiber strips in the expe-rimental groups were treated with the plasma jet for 20 s, 30 s, 40 s and 50 s. The ultimate tensile strength of dentin was measured by universal mechanical machine.RESULTS:(1) The surface morphology of demineralized dentin observed by scanning electron microscope showed that the network structure of collagen fibers on the surface of demineralized dentin treated with the plasma jet for 20 s, 30 s and 40 s could maintain the uncollapsed three-dimensional structure, and part of the microstructure was destroyed after plasma jet treated for 50 s. After being treated by plasma jet for 20 s, 30 s and 40 s, the three-dimensional structure was uncollapsed, and the typical periodic transverse pattern of natural type Ⅰ collagen fiber could be seen. The results of infrared spectra showed that the secondary conformation of dentin collagen fibers was the same as that of the control group after being treated with the plasma jet, and the intensity of amide band was significantly increased after being treated for 30 s and 40 s. (2) The results of ninhydrin crosslinking test showed that the crosslinking ratio of dentin collagen treated by plasma jet for 30 s and 40 s was the highest, and the difference was statistically significant (P < 0.05). (3) The results of dentin ultimate tensile strength showed that the control group was (1.67±0.24) MPa, and the plasma jet treated 20 s, 30 s, 40 s and 50 s groups were (4.21±0.15) MPa, (7.06±0.30) MPa, (7.32±0.27) MPa, and (6.87±0.17) MPa, which were significantly different from that of the control group (P < 0.05).CONCLUSION:The novel RF-APGD plasma jet treatment can promote the crosslinking degree of demineralized dentin collagen and improve their ultimate tensile strength.

Characterization of Cold Atmospheric Plasma-Modified Dentin Collagen

[Effect of a Novel Radio-Frequency Atmospheric-Pressure Glow Discharge Plasma Jet Treatment on Crosslinking of Dentin Collagen].

Effects of a Modified Cold Atmospheric Plasma Jet Treatment on Resin-Dentin Bonding

Influences of the Cold Atmospheric Plasma Jet Treatment on the Properties of the Demineralized Dentin Surfaces

[Effect of a Novel Cold Atmospheric Plasma Jet Treatment with Different Temperatures on Resin-Dentin Bonding].

Enhancing CFRP Laminates with Plasma Jet Arrays: A Study of Interlaminar Mechanical Properties

In vitro study of nonthermal atmospheric pressure plasma in improving the durability of the dentin–adhesive interface with an etch-and-rinse system

The Bond Strength Experiment of Enamel and Dentin Exposed to Pulsed Nd :YAG Laser

Bond Strength Experiment of Human Dentin Following Pulsed Nd:YAG Laser

Effects of a Helium Cold Atmospheric Plasma on Bonding to Artificial Caries-Affected Dentin.

Glutaraldehyde-induced Remineralization Improves the Mechanical Properties and Biostability of Dentin Collagen

Impact of Cold Atmospheric Plasma Treatment on Native and Glycated Collagen

Time-related surface modification of denture base acrylic resin treated by atmospheric pressure cold plasma.

The Efficacy, Safety, Stability, and Mechanism of Tooth Whitening by a Cold Atmospheric Pressure Air Plasma Microjet Assisted with or Without Hydrogen Peroxide

The Effect of NDGA-modified Etchant on the Enzymatic Degradation Resistance and Mechanical Properties of Collagen Matrix

Effect of Different Crosslinkers on Denatured Dentin Collagen's Biostability, MMP Inhibition and Mechanical Properties

Aging Effects Of Fiber Post Surface Treatment With Nonthermal Plasma

Influence of Cold Atmospheric Plasma on Surface Characteristics and Bond Strength of a Resin Nanoceramic.

NDGA Enhances the Physicochemical and Anti-Biodegradation Performance of Dentin Collagen.

Tooth whitening by a direct-current cold atmospheric-pressure air plasma micro jet assisted with a gel containing NO H2O2

Theaflavin −3,3'-digallate/ethanol: a novel cross-linker for stabilizing dentin collagen