Abstract:Polymer electrolyte membrane fuel cells (PEMFC) are required to achieve a durability target of more than 20’000 operating hours for application in the heavy-duty transport sector. To accelerate the wide-spread commercialization of this technology, specific attention is thus dedicated to the degradation mechanisms that affect the membrane and the cathode catalyst layer, the components mostly affected by ageing. A previous experimental analysis of durability [1] pointed out that degradation under real-world operating conditions for automotive applications induces a progressive decline in power density and efficiency, mainly associated to a loss in the electrocatalyst active surface area (ECSA). Further experimental tests confirmed that the cathode ECSA during the initial 1000 hours undergoes a stabilization of the nanoparticle distribution towards an average radius of 7 nm and this degradation is accelerated by excursions to low cell voltage values. Such events occur during regular operation while shutting-down the system for short time (the so called “short-stops”), when air is removed at the cathode side with hydrogen flowing at the anode to avoid air/hydrogen fronts. The aim of this work is to analyze this unexpected acceleration in the ECSA loss for oxygen reduction reaction by means of numerical modelling. Dissolution of platinum nanoparticles in acidic media was extensively analyzed over the last decade and several models were proposed to simulate both cathodic [2] and anodic [3-5] dissolution. These models were applied to the experimental voltage profiles reported in Figure 1(a), which included a low voltage period that mimics a short stop. A systematic study of the low voltage values was carried out in the range between 0.7 V to 0 V. As also observed in Figure 1(b) state-of-the-art models from literature were not able to explain the observed difference between the cases. Aiming to provide a physical description of this aspect a new ageing mechanism was introduced in the model starting from [2] and different model formulations were considered. Formation of PtO 2 was assumed to occur, supported by a specific feature that was observed in cathodic scan of the cyclic voltammetry within the potential range of the short-stop (0.1V - 0.3V vs DHE. The electrocatalyst surface coverage was thus estimated from voltammetry. An additional cathodic dissolution reaction is finally proposed that involves PtO 2 reduction and a kinetic rate was included in the model, in analogy with the existing reaction mechanism taken from [2]. Good consistency was observed with the experimental results reported in Figure 1(c) and also over a wide dataset reporting cathode ECSA loss consequent to different voltage profiles. ECSA stabilization was attributed to the formation of PtO 2 over the corners of the nanoparticle that could explain a mitigation of the dissolution mechanism for particles larger than 7 nm, in which corner sites lead to minor coverage. The results of this work will allow to accelerate the development of mitigation strategies and innovative materials to improve the durability of State-of-the-Art electrocatalysts for PEMFC. This work received support from the Italian government (Progetto PERMANENT - BANDO MITE PNRR Missione 2 Investimento 3.5 A - RSH2A_0O0012). References [1] E. Colombo, A. Baricci, A. Bisello, L. Guetaz, A. Casalegno, PEMFC performance decay during real-world automotive operation: Evincing degradation mechanisms and heterogeneity of ageing , J. Power Sources. 553 (2023) 232246. https://doi.org/10.1016/j.jpowsour.2022.232246. [2] T. Jahnke, A. Baricci, C. Rabissi, A. Casalegno, Physical Modeling of Catalyst Degradation in Low Temperature Fuel Cells: Platinum Oxidation, Dissolution, Particle Growth and Platinum Band Formation [ J. Electrochem. Soc. , 167 , 013523 (2020)], J. Electrochem. Soc. 167 (2020) 149001. https://doi.org/10.1149/1945-7111/abbfda. [3] P. Schneider, C. Sadeler, A.-C. Scherzer, N. Zamel, D. Gerteisen, Fast and Reliable State-of-Health Model of a PEM Cathode Catalyst Layer , J. Electrochem. Soc. 166 (2019) F322–F333. https://doi.org/10.1149/2.0881904jes. [4] H.A. Baroody, E. Kjeang, Predicting Platinum Dissolution and Performance Degradation under Drive Cycle Operation of Polymer Electrolyte Fuel Cells , J. Electrochem. Soc. 168 (2021) 044524. https://doi.org/10.1149/1945-7111/abf5aa. [5] R.K. Ahluwalia, S. Arisetty, J.-K. Peng, R. Subbaraman, X. Wang, N. Kariuki, D.J. Myers, R. Mukundan, R. Borup, O. Polevaya, Dynamics of Particle Growth and Electrochemical Surface Area Loss due to Platinum Dissolution , J. Electrochem. Soc. 161 (2014) F291–F304. https://doi.org/10.1149/2.051403jes. Figure 1

An Experimental Investigation of the Effect of Platinum on the Corrosion of Cathode Carbon Support in a PEMFC.

Analysis of Carbon-Supported Platinum Through Potential Cycling and Potential-Static Holding

Potential-driven instability effect of carbon supports for Pt/C electrocatalysts

Instability of Pt ∕ C Electrocatalysts in Proton Exchange Membrane Fuel Cells A Mechanistic Investigation

Corrosion Mechanism and Mitigation Strategies for Carbon Supports in PEMFCs

Carbon Support Modification for Improving Platinum Performance in PEMFC

Unraveling the Effects of Carbon Corrosion on Oxygen Transport Resistance in Low Pt Loading Proton Exchange Membrane Fuel Cells

The Challenges to Ultra-Low-Platinum PEMFC Cathode and the Electrocatalyst Design Thereof

Surface Engineering of Carbon-Supported Platinum as a Route to Electrocatalysts with Superior Durability and Activity for PEMFC Cathodes

Strong Interaction between Titanium Carbonitride Embedded in Mesoporous Carbon Nanofibers and Pt Enables Durable Oxygen Reduction

Activity and Durability of Platinum-Based Electrocatalysts Supported on Bare or Fluorinated Nanostructured Carbon Substrates

Electrocatalytic and Lifetime Studies of Commercial Catalystsin a PEMFC

Proposing a Model for Platinum Nanoparticles Dissolution in PEM Fuel Cells to Describe Unexplained Electrocatalyst Degradation Consequent to Low Cell Voltage Excursion

Pt/Fe/N/C Catalyst with Improved Activity and Stability Toward Oxygen Reduction Reaction in Proton Exchange Membrane Fuel Cell

The Electrocatalysis of Oxygen Reduction on Platinum and Its Alloys

Perspectives on carbon-alternative materials as Pt catalyst supports for a durable oxygen reduction reaction in proton exchange membrane fuel cells

A sulfur‐modified pore‐blocking method to enhance the electrocatalytic stability of carbon‐supported platinum nanoparticles

Study on Attenuation Mechanism and Durability Improvement of Platinum-Carbon Catalysts for Proton Exchange Membrane Fuel Cells

Transmission Electron Microscopy Observation of Corrosion Behaviors of Platinized Carbon Blacks under Thermal and Electrochemical Conditions

Investigation of the Carbon Corrosion Process for Polymer Electrolyte Fuel Cells Using a Rotating Disk Electrode Technique

High Performance PEM Fuel Cell with Low Platinum Loading at the Cathode Using Magnetron Sputter Deposition