Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Evaluation of the Detonation Characteristics of Aluminized DNAN‐Based Melt‐Cast Explosive by the Detonation Cylinder Test

Detonation Characteristics of an Aluminized DNAN‐Based Melt‐Cast Explosive

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Research of detonation products of RDX/Al from the perspective of composition

Detonation Characteristics of RDX-Liquid Fuel-Air Three-Phase System

On weak influence of aluminum powder size on its post-detonation reaction in different time scales

Influence of Al Content and Surrounding Medium on the Energy Output of Cyclotrimethylenetrinitramine (rdx)/al/wax Explosives

Underwater Detonation Performance of the Aluminum Film Explosive

Influence of Particle Size of Aluminum Powder and Morphology of Oxidizer in Rdx Based Aluminized Explosive on the Ability of Accelerating Metal (I)

Difference in underwater detonation between RDX based aluminum film and aluminum particle explosives

Effects of Nano Aluminum Powder on the Mechanical Sensitivity of RDX-Based Explosives

The influence of aluminum particle size and oxidizer morphology in RDX-based aluminized explosives on their ability to accelerate metals

Detonation performance of cylinder TNT-RDX explosives wrapped by spiral aluminum tube storing high-pressure active gases

Effect of Aluminum Fiber Content on the Underwater Explosion Performance of RDX‐based Explosives

The Influence of Al on the Detonation Parameters of Aluminized Explosives

The effect of active aluminum content on the detonation performance of aluminized explosives

Cylinder Test of Aluminized Explosives and Its Numerical Simulation

Effect of Aluminum Additive on the Detonation Temperature of an Emulsion Explosive

Semi‐closed Investigations of New Aluminized Thermobaric and Enhanced Blast Composites

Activation and reaction mechanism of nano‐aluminized explosives under shock wave

Effect of low-concentration RDX dust on solid–liquid mixed fuel characteristics