Abstract:A microstructure composed of martensite matrix, lower bainite, and stable film-like austenite was designed by a quenching and isothermal bainitic holding process in a 0.30C–2.69Mn–1.71Si (wt.%) steel. The yield strength, tensile strength, and ductile-to-brittle transition temperature (DBTT) of the high-strength steel thus obtained were 1263 MPa, 1521 MPa, and − 33 °C, respectively, and at − 20 °C, it showed superior low-temperature toughness, which reached 77.5 J/cm2. Meanwhile, it showed excellent hydrogen embrittlement (HE) resistance, and the total elongation loss is only 3.1% after 15 min of hydrogen charging. The excellent comprehensive performance is attributed to the fact that fine stable austenite with film-like morphology hindered the crack nucleation and propagation, and hindered hydrogen diffusion as a hydrogen trap. However, with a decrease in the isothermal temperature, transition carbide precipitation was accompanied by a further decrease in austenite grain size. For this condition, although transition carbides can act as effective hydrogen traps, excessive precipitation decreased the carbon content of retained austenite and increased the deformation heterogeneity between austenite and martensite matrix, leading to weakened austenite stability and HE resistance, a total elongation loss of approximately 39% (15 min hydrogen charging), a sharp decrease in impact toughness, and an increase in DBTT. The competitive role of film-like austenite and transition carbides on the comprehensive mechanical performance of steel is revealed, especially the suppression of crack nucleation and propagation that will provide a guide for the design of high strength steels with excellent impact toughness and HE resistance.

Roles of pre-formed martensite in below-Ms bainite formation, microstructure, strain partitioning and impact absorption energies of low-carbon bainitic steel

Effect of Austempering Processes on the Tensile Properties and the Work-Hardening Behavior of Austempered Bainitic Steels Below the Martensite Start Temperature

Influence of Prior Martensite on Bainite Transformation, Microstructures, and Mechanical Properties in Ultra-Fine Bainitic Steel

Roles of pre-formed martensite in deformation behavior and strain partitioning of medium-carbon bainitic steel by quasi-in-situ tensile tests

Effect of prior martensite formation on the bainite transformation kinetics in high-strength 3% Mn multiphase steel

Effect of Austempering below and above Ms on the Microstructure and Wear Performance of a Low-Carbon Bainitic Steel

Microstructural evolution and ultra-high impact toughness of austempered lamellar bainitic steel far below Ms temperature

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes

Roles of cooling rate of undercooled austenite on isothermal transformation kinetics, microstructure, and impact toughness of bainitic steel

Effect of refined multi-scale microstructures on the ultra-high impact toughness of bainitic steel austempered below Ms temperature

Competitive role of film-like austenite and transition carbides on hydrogen embrittlement resistance and impact toughness in bainite-containing quenched and partitioned steel

Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below M

The Role of Microstructural Constituents on Strength–Ductility–Local Formability of a Transformation‐Induced‐Plasticity‐Aided Bainitic Steel

Effect of prior martensite on bainite transformation and microstructure of high-carbon nano-bainitic steel

Effect of martensite pre-quenching on bainite transformation kinetics, martensite/bainite duplex microstructures, mechanical properties and retained austenite stability of GCr15 bearing steel

Study of microstructural evolution and mechanical properties of 1000 MPa low-carbon microalloyed steel prepared by multiple quenching strategies near Ms

Microstructure and Mechanical Properties of Low- and Medium-Carbon Si-Rich Low-Alloy Steels Processed by Austemping after Intercritical Annealing

Effect of Austenite Grain Size on the Bainitic Transformation in a 690 MPa Grade High-Strength Multi-Functional Construction Steel

Characteristics and Kinetics of Bainite Transformation Behaviour in a High-Silicon Medium-Carbon Steel above and below the Ms Temperature

The Role of Retained Austenite on the Mechanical Properties of a Low Carbon 3Mn-1.5Ni Steel