Passband Flattening in Waveguide Grating Devices Using Phase-Dithering

Jian-Jun He,Emil S. Koteles,Bedwyr Humphreys

DOI: https://doi.org/10.1364/ipr.2002.ife2

2002-01-01

Abstract:A new passband flattening technique for waveguide grating devices is proposed and experimentally verified. It uses phase modification of grating elements to flatten and steepen the passband shape while maintaining single mode input and output waveguides.

What problem does this paper attempt to address?

Phase-dithered Waveguide Grating with Flat Passband and Sharp Transitions

JJ He

DOI: https://doi.org/10.1109/jstqe.2002.805969

IF: 4.9

2002-01-01

IEEE Journal of Selected Topics in Quantum Electronics

Abstract:A new passband flattening technique for waveguide grating devices is proposed and experimentally demonstrated. It uses phase dithering of grating elements to obtain a flat passband with sharp transitions while maintaining single-mode input and output waveguides. The chromatic dispersion characteristics of the device can be improved simultaneously over the passband. The theory and design method based on an iterative Fourier transform algorithm are presented in detail with simulation and experimental results. The technique can be used in both arrayed waveguide grating and echelle grating-based devices.
Design of Polarization Band-Pass Filters Based on the Theory of Thin-Film Photonic Crystal Superlattice

GP Fu,HX Chen,XY Qin,X Liu

DOI: https://doi.org/10.7498/aps.54.773

IF: 0.906

2005-01-01

Acta Physica Sinica

Abstract:The principle of design of polarization band_pass filters used for wavelength d ivision multiplexing systems is presented. The design method is based on the con cept of thin_film photonic crystal superlattice. Two kinds of design are put for ward. One of them is to construct by superposition of two photonic crystals; and the other is to insert a new photonic crystal into the middle of a photonic cr ystal, so that there are in effect three photonic crystals. Such band_pass filte rs have excellent optical properties with p_polarization transmittance and s_pol arization reflectance. The characteristics of the filters, including peak transm ittance, half_band width and rejection are discussed.
Graded Wavelike Two-Dimensional Photonic Crystal Made of Thin Films

Yi-Yu Li,Ming-Yu Li,Pei-Fu Gu,Zhen-Rong Zheng,Xu Liu

DOI: https://doi.org/10.1364/ao.47.000c70

IF: 1.9

2007-01-01

Applied Optics

Abstract:A filling-factor-graded wavelike two-dimensional photonic crystal (2DPC) possessing a light-path bending effect that is polarization dependent is theoretically studied by using a qualitative analysis of the isofrequency curves. The numerical simulation results obtained by using the finite-difference time-domain method demonstrate that such a graded 2DPC has potential applications in a polarization splitter and a parallel-plane resonant cavity. A new kind of waveguide structure that combines a filling-factor-graded wavelike 2DPC and one-dimensional multilayer thin films is also discussed.
Diffraction Properties of Transmission Binary Blazed Grating

Hui-Jun Zhou,Qu-Quan Wang

IF: 0.6

2006-01-01

Optica Applicata

Abstract:The properties of binary blazed grating were theoretically analyzed with finite-difference time-domain (FDTD) method. The diffraction efficiencies and diffraction angles of -1, 0, and +1 order for the grating varying with wavelength, grating structure, and the etch depth were studied when the incident angle was 30 degrees. The numerical simulations revealed that the binary blazed grating presented high stability of diffraction efficiencies with wavelength shift.
A Passband-Flattened EDG Demultiplexer with an Air-Trenched Taper

Zhongyan Sheng,Sailing He

DOI: https://doi.org/10.1080/01468030390237842

2010-01-01

Abstract:A novel passband flattening method for a planar waveguide demultiplexer based on an etched diffraction grating is presented. A strongly confined taper is formed by etching air trenches at both sides of the input waveguide. The geometric parameters of the taper are optimized by considering the figure of merit, ripple, and loss. Numerical simulation for a design example is given to illustrate the passband flattening method.
Substrate Integrated Waveguide Filter with Flat Passband Based on Complex Couplings

Liang-Feng Qiu,Lin-Sheng Wu,Bing Xie,Wen-Yan Yin,Jun-Fa Mao

DOI: https://doi.org/10.1109/lmwc.2018.2829349

IF: 3

2018-01-01

IEEE Microwave and Wireless Components Letters

Abstract:A lossy filter with flat passband and asymmetric response is proposed by using complex couplings. The complex coupling coefficients with positive and negative imaginary parts are realized with transmission lines loaded with series and shunt resistors, respectively. Design formulas are derived for the critical parameters. A filter prototype is developed at 4.97 GHz and substrate integrated waveguide resonators with unloaded Q-factor of 450 are used. One transmission zero is located in its upper stopband. The 0.2-dB bandwidth of 279 MHz is achieved and the equivalent Q-factor is about 1900. Good agreement is obtained among the synthesized, simulated, and measured results.
Binary Approximate Structure of Blazed Grating

ZHOU Hui-Jun,Wang Qu-Quan

DOI: https://doi.org/10.3969/j.issn.1672-3392.2005.03.011

2005-01-01

Abstract:The blazed grating can be used to fabricate waveguide coupler with high efficiency. With FDTD method, the first order diffractive efficiency and diffraction angle of binary blazed grating with different structure are simulated. The result of the numerical simulation is of great important for the fabrication of binary blazed grating.
A Lateral Shift Apodized Waveguide Grating

Jianfei Jiang,Huiye Qiu,Hui Yu,Jianyi Yang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/iprsn.2017.jtu4a.1

2017-01-01

Abstract:A lateral shift apodized waveguide grating is presented and demonstrated. The apodized profile is mapped into lateral shifts of the grating sidewall. The results show high side-lobes suppress ratio and larger fabrication tolerance.
Recent Advances in InP-based Waveguide Grating Demultiplexers

Koteles, E.S.,He, J.J.,Lamontagne, B.,Delage, A.

DOI: https://doi.org/10.1109/ofc.1998.657225

1998-01-01

Abstract:Summary form only given. We present detailed modeling and experimental results for an improved design of an InGaAsP/InP wavelength demultiplexer based on a monolithically-integrated Rowland circle waveguide grating fabricated using chemically-assisted ion beam etching. The design incorporates ten wavelength channels at 1.55 /spl mu/m with a uniform spacing of 2 nm and multimode output waveguides to flatten channel response and reduce sensitivity to polarization.
Etched Diffraction Grating Wavelength Router with Uniform-Loss and Flat-Passband

Mu Ge,He Jianjun

DOI: https://doi.org/10.3788/aos201636.0606001

2016-01-01

Abstract:An etched diffraction grating wavelength router (EDGR) with arc-shaped grating teeth is proposed,and the loss uniformity and spectral passband of the device can be improved simultaneously with proper design for the shape of the grating teeth.A 4 × 4 EDGR with 400 GHz channel spacing,centered at 1550 nm and based on InP platform is designed.Simulation results show that the loss difference of all channels is reduced from 8.1 dB to 0.8 dB.The shape of the spectral response is flat-top and the 1 dB bandwidth is increased from 0.3 nm to 1.6 nm.By adjusting the design parameters,the loss uniformity,bandwidth and entire loss of the device can be balanced.Experimental results show that the loss difference of all channels is 3.1 dB and 1 dB bandwidth is 1.1 nm.The crosstalk of the device is better than-12 dB.The validity of this method is verified.This method does not need to increase the chip size or add extra elements,which can be applied to etched diffraction gratings in any material platform.
Facet-Rotated Echelle Grating for Cyclic Wavelength Router with Uniform Loss and Flat Passband

Ge Mu,Pingli Huang,Lin Wu,Jian-Jun He

DOI: https://doi.org/10.1364/ol.40.003978

IF: 3.6

2015-01-01

Optics Letters

Abstract:A novel method for designing a cyclic echelle grating wavelength router with uniform loss and flat passband is proposed and experimentally demonstrated. A 4×4 cyclic wavelength router with a channel spacing of 400 GHz at 1550 nm wavelength band is designed and fabricated in InP. Measurement results show that the loss of 16 input-output combinations varies from 9 to 19.3 dB in a conventional design, with a nonuniformity of 10.3 dB, while the 1-dB spectral bandwidth is only 0.3 nm. By rotating angles of grating facets according to an appropriately designed distribution function, the loss nonuniformity is reduced to 1.5 dB, and a flat-top spectral response with 1 dB bandwidth of 1.0 nm is achieved simultaneously.
Analysis on Curved Waveguide Grating (CWG) with Rowland circle construction

Yinlei Hao,Jianyi Yang,Xiaoqing Jiang,Wei Zheng,Jianying Zhou,Haifeng Zhou,Minghua Wang

DOI: https://doi.org/10.1109/AOE.2007.4410800

2008-01-01

Abstract:Configuration of Curved Waveguide Grating (CWG) with Rowland circle construction is presented, working mechanism of CWG is demonstrated, result show that CWG is a promising candidate wavelength demultiplexer in optical DWDM network.
An Analytic Method for Designing Passband Flattened Dwdm Demultiplexers Using Spatial Phase Modulation

ZM Shi,HJ He,SL He

DOI: https://doi.org/10.1109/jlt.2003.817696

IF: 4.7

2003-01-01

Journal of Lightwave Technology

Abstract:An analytic method of spatial phase modulation based on Fourier analysis is introduced for the design of a planar waveguide demultiplexer with a flat-top spectral response. An analytic formula for an etched diffraction grating demultiplexer is derived using the scalar diffraction theory. The spatial phase modulation is realized by slightly adjusting each grating facet's position according to the analytic formula to obtain a spectral response with a flat top and sharp transitions as well as a good dispersion characteristic. The analytic formula is characterized by two parameters: a transverse shift distance and a profile exponent for the phase modulation. A linear relation between the passband width and the transverse shift distance is given, and an optimal figure of merit of the spectral response is obtained by choosing an appropriate profile exponent. A numerical example of a typical SiO2 etched diffraction grating demultiplexer is used to demonstrate the advantages of this method.
Monolithic Integrated Wavelength Demultiplexer Based on a Waveguide Rowland Circle Grating in InGaAsP/lnP

JJ He,B Lamontagne,A Delage,L Erickson,M Davies,ES Koteles

DOI: https://doi.org/10.1109/50.664075

IF: 4.7

1998-01-01

Journal of Lightwave Technology

Abstract:We present detailed modeling and experimental results for an improved design of an InGaAsP/lnP wavelength demultiplexer based on a monolithically integrated Rowland circle grating. The design incorporated ten wavelength channels at 1.55 mu m with a uniform spacing of 2 nm. The total on-chip loss was about 10 dB and the crosstalk between adjacent channels was as low as -25 dB. It was shown that low-loss etched turning mirrors can reduce the total on-chip loss by about 4 dB compared to traditional 90 degrees curved multimode waveguides. By replacing standard hat grating facets with retro-reflecting V-shaped facets in the echelle grating, the loss was further reduced by 4 dB, Polarization independent operation within a passband of 0.5 nm was achieved by using multimode output waveguide, The potential sources producing the crosstalk have been analyzed and fabrication modifications for further improvement are suggested.
InP Based Echelle Diffraction Grating Multiplexer with Flat-Passband

Lili Le,Yayan Chu,Zhipeng Hu,Jinyan Song,Jian-Jun He

DOI: https://doi.org/10.1109/icocn.2017.8121401

2017-01-01

Abstract:An echelle diffraction grating (de)multiplexer with arc shaped grating teeth, based on a multi-guide vertical integration platform in InP is presented. The device can be applied to the 100GBASE-LR4 Ethernet systems, the crosstalk is better than -19 dB. By adjusting grating facets, the 3-dB spectral bandwidth is increased to 2.2 nm compared with 1.7 nm in a conventional design with a loss penalty less than 2 dB. And the nonuniformity is reduced form 1.7 dB to 0.68 dB.
Silica-Based Arrayed Waveguide Grating With Flattened Spectral Response Using A Multimode Interference Coupler

Yz Tang,Km Jia,By Li,Jy Yang,Xq Jiang,Ym Wu,Yl Wang

DOI: https://doi.org/10.1088/0256-307X/21/6/024

2004-01-01

Chinese Physics Letters

Abstract:We designed and fabricated an arrayed waveguide grating based on silica-on-silicon materials with flattened spectral response by adding a multimode interference coupler in the input region. The theoretical analysis and calculation are given. The device has worked effectively and has been tested with the passband 0.43 nm at 1 dB, 0.72 nm at 3 dB and 1.56 nm at 20 dB respectively, at a cost of power penalty of about 1.5 dB. The crosstalk is less than -30 dB, owing to the high-resolution photomask and well-controlled fabrication processes.
Analysis for Passband Flatness of Arrayed Waveguide Grating Multiplexer

Zheng-kun QIN,Chun-sheng MA,De-lu LI,Hai-ming ZHANG,Da-ming ZHANG,Shi-yong LIU

DOI: https://doi.org/10.3321/j.issn:1005-0086.2006.05.007

2006-01-01

Abstract:An efficient technique is proposed to flatten the spectral response of an arrayed waveguide grating (AWG) multiplexer. By subtracting an increment from the length difference of odd arrayed waveguides and adding the same increment to that of even arrayed waveguides, a box-like spectral response can be obtained. The simulated result for a 17 × 17 polymer AWG shows that the box-like spectral response has a 3 dB bandwidth of 0.49 nm, and the crosstalk is about or less than -28 dB for every output channel.
A Planar Waveguide Concave Grating Employing Dielectric Mirrors

Chun-Ting Lin,Yang-Tung Huang,Jung-Yaw Huang

DOI: https://doi.org/10.1016/j.optcom.2007.10.062

IF: 2.4

2007-01-01

Optics Communications

Abstract:Dielectric mirrors, which yield high-reflectances on grating facets, are proposed for the design of a planar waveguide concave grating. The transfer-matrix method is used to derive an expression for the reflectance of a series of air slots and high-index stacks. The FullWAVE software, a finite difference time-domain EM solver from R-Soft, is used to evaluate the loss of the resulting 2D waveguide grating. The simulation results show that the polarization-dependent loss (PDL) is below 0.25dB when the proposed dielectric mirror is used. The influence of the width variation of the dielectric stack is also taken into account.
Device for concatenation of phase-shifted long-period grating and its application as gain-flattening fiber filter

Yinian Zhu,Beatrys M. Lacquet,Pieter L. Swart,Stephanus J. Spammer,Ping Shum,Chao Lu

DOI: https://doi.org/10.1117/1.1564105

IF: 1.3

2003-05-01

Optical Engineering

Abstract:The transmission characteristics of phase-shifted long-period gratings (LPGs) are simulated theoretically using coupled-mode theory and the fundamental-matrix method. A phase-shifted LPG device cascaded with another uniform LPG can be used to flatten the gain spectrum of an erbium-doped fiber amplifier (EDFA) with three gain peaks. The results of all simulations have shown that a broadband amplifier with a 0.7-dB peak-to-peak gain variation over 36 nm can be realized practically. Using our designed and fabricated device, the experimental results show that the 3-dB bandwidth of the flattened EDFA is increased from 18 to 46 nm for an unequalized spectrum. The gain ripple over that bandwidth is reduced to approximately 0.9 dB. The improvement by a factor of 2 to 3 is realized in the sprectral performance. Such a gain-flattening fiber filter is indeed plausible and has a practical application in dense wavelength-division multiplexed (DWDM) telecommunication systems. © 2003 Society of Photo-Optical Instrumentation Engineers.

optics
Design Technique for Guided-Wave Gratings

Lifeng Li,James Burke,George Stegeman,Colin T. Seaton

DOI: https://doi.org/10.1364/oam.1987.mk1

1987-01-01

Abstract:We present a design technique for accurately predicting coupling efficiency in guided-wave applications of gratings. We approach the problem by separating the planar waveguide and diffraction grating. The wave guiding is treated by ray optics techniques, and grating diffraction is treated by rigorous diffraction grating theory or direct measurement. In this way, we get more feeling for the working of the grating as a diffraction element and how it interacts with the waveguide structure. When the grating groove depth is small our results agree with the phenomenological expressions given by Zory1 and the result of coupled-mode theory by Yariv.2 It is shown that the phase difference between reflected plane waves with and without the presence of the grating is important for determining the reflection coefficient of a distributed feedback reflector.

Passband Flattening in Waveguide Grating Devices Using Phase-Dithering

Phase-dithered Waveguide Grating with Flat Passband and Sharp Transitions

Design of Polarization Band-Pass Filters Based on the Theory of Thin-Film Photonic Crystal Superlattice

Graded Wavelike Two-Dimensional Photonic Crystal Made of Thin Films

Diffraction Properties of Transmission Binary Blazed Grating

A Passband-Flattened EDG Demultiplexer with an Air-Trenched Taper

Substrate Integrated Waveguide Filter with Flat Passband Based on Complex Couplings

Binary Approximate Structure of Blazed Grating

A Lateral Shift Apodized Waveguide Grating

Recent Advances in InP-based Waveguide Grating Demultiplexers

Etched Diffraction Grating Wavelength Router with Uniform-Loss and Flat-Passband

Facet-Rotated Echelle Grating for Cyclic Wavelength Router with Uniform Loss and Flat Passband

Analysis on Curved Waveguide Grating (CWG) with Rowland circle construction

An Analytic Method for Designing Passband Flattened Dwdm Demultiplexers Using Spatial Phase Modulation

Monolithic Integrated Wavelength Demultiplexer Based on a Waveguide Rowland Circle Grating in InGaAsP/lnP

InP Based Echelle Diffraction Grating Multiplexer with Flat-Passband

Silica-Based Arrayed Waveguide Grating With Flattened Spectral Response Using A Multimode Interference Coupler

Analysis for Passband Flatness of Arrayed Waveguide Grating Multiplexer

A Planar Waveguide Concave Grating Employing Dielectric Mirrors

Device for concatenation of phase-shifted long-period grating and its application as gain-flattening fiber filter

Design Technique for Guided-Wave Gratings