Lightweight Full-Color Holographic 3D Display System Based on Color Dispersion Compensation Method

Shu-Feng Lin,Di Wang,Qiong-Hua Wang

DOI: https://doi.org/10.1364/dh.2020.hf4d.7

2020-01-01

Abstract:Usually, achieving full-color holographic 3D display consumes a lot of resources. In order to solve the problem, a lightweight full-color holographic 3D display system using a single SLM based on color-dispersion compensation method is proposed.

What problem does this paper attempt to address?

Holographic three-dimensional display based on shifted Fraunhofer diffraction

Peng Sun,Zeqing Yu,Chenning Tao,Siqi Liu,Xiao Tao,Chang Wang,Zhenrong Zheng

DOI: https://doi.org/10.1117/12.2573430

2020-01-01

Abstract:Holographic display has attracted considerable attention for its high-contrast, low power consumption, wide color gamut and potentials for three-dimensional (3D) display. Although computer-generated hologram (CGH) has the potential for reconstructing all the 3D information of an object, complicated 3D modeling and time-consuming computation are big challenges faced by current 3D holographic display. A simple yet effective method to realize holographic 3D display by shifted Fraunhofer diffraction has been presented in this paper. After a 3D object is divided into a set of layers in axial direction, these layers are calculated into corresponding sub-holograms by Fraunhofer diffraction. The hologram uploaded on SLM consists of sub-holograms in a tiling approach. Both simulations and experiments are carried out to verify the feasibility of shifted Fraunhofer diffraction. Detailed analysis of computational cost has also been carried out, and the comparison between shifted Fresnel diffraction and shifted Fraunhofer diffraction in the proposed method has been analyzed. The Analysis results shows that the process of 3D modeling is simple, that is the computational complexity is accordingly reduced compared with shifted Fraunhofer diffraction. The experimental results demonstrate that our method can reconstruct multi-plane 3D object with continuous depth map. It is expected that the proposed method may provide a better solution in future holographic 3D display research.
Reproduction of a Computer-Generated Hologram with a White Light Source and Liquid Crystal Device

Xiao-jie Zhang,Xu Liu,Hai-feng Li

DOI: https://doi.org/10.1117/1.2714982

IF: 1.3

2007-01-01

Optical Engineering

Abstract:The reproduction of computer-generated hologram (CGH) with white light source was realized using a liquid crystal panel instead of holographic film. The Burch-coding CGH was achieved by simulating the interference of a digital image and virtual reference light, displayed on liquid crystal displays and illuminated by a white light-emitting diode. The system is compact and the reconstructed images include full parallax. The full-parallax images of the Fresnel hologram computed with our algorithm were compared with the reproduced images by the rainbow hologram. The results implied this method was ready for the development of real-time three-dimensional color digital holography. (C) 2007 Society of Photo-Optical Instrumentation Engineers.
Binocular full-color holographic three-dimensional near eye display using a single SLM

Shu-Feng Lin,Shi-Hang Zhang,Jie Zhao,Lu Rong,Yunxin Wang,Dayong Wang

DOI: https://doi.org/10.1364/OE.480062

2023-01-16

Abstract:A binocular full-color holographic three-dimensional near eye display system using a single spatial light modulator (SLM) is proposed. In the display system, the frequency spectrum shifting operation and color spectrum shifting operation are adopted to realize the frequency division multiplexing (FDM) and frequency superposition multiplexing (FSM) by manipulating the frequency spectrums of each color- and view-channel sub-holograms. The FDM combined with polarization multiplexing will be used to implement binocular display using a single SLM, and the FSM working with a bandpass filter for each view-channel will be used to achieve full-color display from single frame hologram. The optical analysis and experiments with 3D color objects confirm the feasibility of the proposed system in the practical application.
Holographic Three-Dimensional Display Based on Optimizing Arrangement of Holograms

Peng Sun,Chenning Tao,Jinlei Zhang,Rengmao Wu,Siqi Liu,Qinzhen Tao,Chang Wang,Fei Wu,Zhenrong Zheng

DOI: https://doi.org/10.1016/j.optcom.2020.125260

IF: 2.4

2020-01-01

Optics Communications

Abstract:We present a simple yet effective method to realize holographic three-dimensional (3D) display by optimizing arrangement of holograms. After a 3D object is divided into a set of layers in axial direction, these layers are calculated into corresponding sub-holograms by Fraunhofer diffraction. The hologram uploaded on SLM consists of sub-holograms side-by-side. Both simulations and experiments are carried out to verify the feasibility of the proposed method. The difference between Fresnel diffraction and Fraunhofer diffraction in the proposed method is analyzed. Aiming at the problems exposed in the experiments, reconstructed results are discussed and further improved by optimizing arrangement of sub-holograms. The process of 3D modeling is simple and the computational complexity is accordingly reduced. This method may provide a promising solution in future holographic 3D realization.
Holographic near-eye display system based on double-convergence light Gerchberg-Saxton algorithm.

Peng Sun,Shengqian Chang,Siqi Liu,Xiao Tao,Chang Wang,Zhenrong Zheng

DOI: https://doi.org/10.1364/OE.26.010140

IF: 3.8

2018-01-01

Optics Express

Abstract:In this paper. a method is proposed to implement noises reduced three-dimensional (3D) holographic near-eye display by phase-only computer-generated hologram (CGH). The CGH is calculated from a double-convergence light Gerchberg-Saxton (GS) algorithm, in which the phases of two virtual convergence lights are introduced into GS algorithm simultaneously. The first phase of convergence light is a replacement of random phase as the iterative initial value and the second phase of convergence light will modulate the phase distribution calculated by GS algorithm. Both simulations and experiments are carried out to verify the feasibility of the proposed method. The results indicate that this method can effectively reduce the noises in the reconstruction. Field of view (FOV) of the reconstructed image reaches 40 degrees and experimental light path in the 4-f system is shortened. As for 3D experiments, the results demonstrate that the proposed algorithm can present 3D images with 180cm zooming range and continuous depth cues. This method may provide a promising solution in future 3D augmented reality (AR) realization. (C) 2018 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
Simply structured full-color holographic three-dimensional display using angular-compensating holographic optical element

Shu-Feng Lin,Philippe Gentet,Di Wang,Seung-Hyun Lee,Eun-Soo Kim,Qiong-Hua Wang

DOI: https://doi.org/10.1016/j.optlaseng.2020.106404

IF: 5.666

2021-03-01

Optics and Lasers in Engineering

Abstract:<p>A simply structured full-color holographic three-dimensional (3D) display system using an angular-compensating holographic optical element (ACHOE) is proposed. This system adds an ACHOE into the traditional monochrome display system to realize a full-color display system. The ACHOE can increase the separation angle of color dispersion by increasing the angle difference of different colors, making it possible to directly use a white light source illuminating a single spatial light modulator for full-color display. As additional optical elements to synthesize full-color reconstruction and to remove the unnecessary diffracted images are not required, the proposed system is very simple, which is beneficial to function integration and system miniaturization.</p>

optics
Compact Full-Color Holographic 3-D Display Based on Undersampled Computer-Generated Holograms and Oblique Projection Imaging.

Hong-Kun Cao,Yong-Seok Hwang,Eun-Soo Kim,Xin Jin

DOI: https://doi.org/10.1364/oe.410034

IF: 3.8

2020-01-01

Optics Express

Abstract:A compact full-color electro-holographic three-dimensional (3-D) display with undersampled computer-generated holograms (US-CGHs) and oblique projection imaging (OPI) is proposed. For its realization, undersampling conditions of the CGH enabling the complete recovery of image information are derived, and the OPI-based longitudinal-to-lateral depth conversion (LTL-DC) scheme allowing the simple reconstruction of full-color images is also proposed. Three-color off-axis US-CGHs are generated with their center-shifted principle fringe patterns (CS-PFPs) of the novel look-up table (NLUT) method, where center-shifts are calculated with the derived undersampling conditions of the CGH based on the generalized sampling theorem, and then multiplexed into the color-multiplexed hologram (CMH). The CMH is loaded on a SLM (spatial light modulator) and reconstructed by being illuminated with a multi-wavelength light source, where an original full-color image is reconstructed being spatially separated from the other color-dispersed images on the projected image plane with the OPI-based LTL-DC process, which enables us to view the original full-color image just with a simple filter mask. Performance analysis and successful experiments with the test 3-D objects in motion confirm the feasibility of the proposed system.
Ultrahigh-fidelity full-color holographic display via color-aware optimization

Chun Chen,Seung-Woo Nam,Dongyeon Kim,Juhyun Lee,Yoonchan Jeong,Byoungho Lee

DOI: https://doi.org/10.1186/s43074-024-00134-7

IF: 16.5

2024-06-03

PhotoniX

Abstract:Holographic display offers the capability to generate high-quality images with a wide color gamut since it is laser-driven. However, many existing holographic display techniques fail to fully exploit this potential, primarily due to the system's imperfections. Such flaws often result in inaccurate color representation, and there is a lack of an efficient way to address this color accuracy issue. In this study, we develop a color-aware hologram optimization approach for color-accurate holographic displays. Our approach integrates both laser and camera into the hologram optimization loop, enabling dynamic optimization of the laser's output color and the acquisition of physically captured feedback. Moreover, we improve the efficiency of the color-aware optimization process for holographic video displays. We introduce a cascade optimization strategy, which leverages the redundant neighbor hologram information to accelerate the iterative process. We evaluate our method through both simulation and optical experiments, demonstrating the superiority in terms of image quality, color accuracy, and hologram optimization speed compared to previous algorithms. Our approach verifies a promising way to realize a high-fidelity image in the holographic display, which provides a new direction toward the practical holographic display.

optics
High-Quality Holographic 3D Display System Based on Virtual Splicing of Spatial Light Modulator

Di Wang,Zhao-Song Li,Yi-Wei Zheng,Nan-Nan Li,Yi-Long Li,Qiong-Hua Wang

DOI: https://doi.org/10.1021/acsphotonics.2c01514

IF: 7

2022-12-11

ACS Photonics

Abstract:Holographic 3D display technology is a kind of naked-eye 3D display technology that can realize the undifferentiated fusion of the virtual reconstructed image and real scene without causing visual fatigue in viewers. However, constrained by narrow viewing angle, small size, and serious speckle noise, the progress of current holographic 3D display technology is hampered. In this paper, a high-quality holographic 3D display system based on virtual splicing of spatial light modulators (SLMs) is proposed. By using the temporal division multiplexing method and two specially tailored beam deflection elements, a large-scale virtual splicing of SLMs is realized. Meanwhile, a physical model-driven network (PMD-Net) is proposed, which is able to quickly calculate a noise-suppressed hologram within 100 ms. Based on the PMD-Net, two hologram calculation methods are designed to realize the large viewing angle and large size holographic 3D display, respectively. With the proposed system, the viewing angle and size of the reconstructed image are enlarged by 3 times, respectively. Moreover, the speckle noise is reduced by 50% compared with the traditional methods. The proposed system realizes a high-quality holographic 3D display effect and is expected to be applied in education, entertainment, and medical fields.

physics, condensed matter,optics, applied,materials science, multidisciplinary,nanoscience & nanotechnology
Convolutional Symmetric Compressed Look-Up-table Method for 360° Dynamic Color 3D Holographic Display.

Jiahao Wei,Chenxiao Wei,Haowen Ma,Dapu Pi,Haifeng Li,Xu Liu,Yongtian Wang,Juan Liu

DOI: https://doi.org/10.1364/oe.494745

IF: 3.8

2023-01-01

Optics Express

Abstract:In this paper, we propose a convolutional symmetric compressed look-up-table (CSC-LUT) method to accelerate computer-generated hologram (CGH) computation based on the Fresnel diffraction theory and LUT. The proposed method can achieve one-time high-quality fast generation of color holograms by utilizing dynamic convolution operation, which is divided three processes. Firstly, the pre-calculated data of maximum horizontal modulation factor is compressed in 1D array by coordinate symmetry. Then, the test object is resampled to satisfy convolutional translation invariance. Finally, the dynamic convolution operation is used to simplify CGH computation process rather than the point-by-point computation. Numerical simulation and optical experimental results show that our proposed method can achieve faster computation speed, higher reconstruction quality and wider application compared to conventional SC-LUT method. The further optimization method for parallel acceleration on the GPU framework can achieve real-time (>24fps) color holographic display corresponding to three perspectives of a 3D scene.
Compact Lensless Full-Color Holographic Projection System with Digital Phase

Zhaoyu Gong,Xing Chen,Zhongyuan Guo,Feihong Yu

DOI: https://doi.org/10.1364/osac.380132

2020-01-01

OSA Continuum

Abstract:A lensless full-color holographic projection system is proposed, satisfying the requirement of compactness and flexibility. The system enables projection by illuminating a single-chip spatial light modulator (SLM) simultaneously with red (R), green (G), and blue (B) lasers, in which the SLM loads a color-multiplexed phase-only hologram. To strengthen compactness, filtering and achromatic systems are achieved by digital phase, where the digital lens phase focuses the light field onto the filter plane, and the digital blazed gratings shift the RGB images to achieve a fine alignment. Besides, the flexibility of diffraction calculation is enhanced by the cascaded D-FFT and S-FFT algorithm (CDS algorithm, where D-FFT is acronym of double fast fourier transform and S-FFT is acronym of single fast fourier transform). Both simulation and optical experiments are carried out. We conducted 2D image and animation projection and multi-image-plane projection. The results confirm the feasibility of our method.
Full-Color See-Through Three-Dimensional Display Method Based on Volume Holography

Taihui Wu,Jianshe Ma,Chengchen Wang,Haibei Wang,Ping Su

DOI: https://doi.org/10.3390/s21082698

IF: 3.9

2021-01-01

Sensors

Abstract:We propose a full-color see-through three-dimensional (3D) display method based on volume holography. This method is based on real object interference, avoiding the device limitation of spatial light modulator (SLM). The volume holography has a slim and compact structure, which realizes 3D display through one single layer of photopolymer. We analyzed the recording mechanism of volume holographic gratings, diffraction characteristics, and influencing factors of refractive index modulation through Kogelnik's coupled-wave theory and the monomer diffusion model of photopolymer. We built a multiplexing full-color reflective volume holographic recording optical system and conducted simultaneous exposure experiment. Under the illumination of white light, full-color 3D image can be reconstructed. Experimental results show that the average diffraction efficiency is about 53%, and the grating fringe pitch is less than 0.3 mu m. The reconstructed image of volume holography has high diffraction efficiency, high resolution, strong stereo perception, and large observing angle, which provides a technical reference for augmented reality.
Color Virtual Display Based On Planar Waveguide With Transmission Volume Holograms

Hui Liu,Zhenrong Zheng,Haifeng Li,Xu Liu

2011-01-01

Abstract:Color virtual image display based on light-guided hologram is presented. It includes in-out coupling transmission volume hologram elements recorded on a single transparent planar waveguide. In the paper; the approach to overcome different diffraction for RGB (the primary colors) and achieve an optimal field of view (FOV) is given. The intensity uniformity of different waves and angles is taken into consideration, and therefore image quality is comparatively maintained over the screen. The simulation results reveal that a horizontal FOV of 15.95 degrees and a vertical FOV of 12 degrees can be achieved. There will be a tilt view angle 10.27 degrees, but it's acceptable in practical application.
High-resolution Fresnel hologram information simplification and color 3D display

Xin Yang,FuYang Xu,HongBo Zhang,Hui Wang,Yong Li,JiaHeng Zhang

DOI: https://doi.org/10.1016/j.ijleo.2020.164919

IF: 3.1

2020-08-01

Optik

Abstract:<p>High-resolution color Fresnel hologram is computation extensive. In this research, we propose a spatial sampling method to reduce the information redundancy of high-resolution Fresnel holograms. The color Fresnel hologram by combining of three monochromatic sampled holograms is achieved without barrier effect. Theoretical analysis of human visual perception of the color Fresnel hologram is conducted. A color holographic 3D display method using RGB LEDs as illumination sources is implemented for color holographic 3D display using color Fresnel holograms with the size of 30 mm × 30 mm at the resolution of 94,208 × 94,208 pixels. The proposed method is verified through experimental study illustrating the effectiveness of the proposed method.</p>

optics
Crosstalk-Free Multiplane Full-Color Holography Based on the Space Division Method

Axiu Cao,Yingfei Pang,Qiling Deng

DOI: https://doi.org/10.3390/photonics11030230

IF: 2.536

2024-03-03

Photonics

Abstract:This paper has proposed a full-color holography based on the space division method to provide a new solution for three-dimensional color holographic display. The hologram is divided into three different regions for the R, G, and B trichromatic hologram components, which will be designed separately at the corresponding positions. The projection images at different projection depths are preprocessed to meet dimension matching and position matching conditions. Different color images are reconstructed on a single plane and 19 planes in simulations and experiments, respectively, which verify the feasibility of the method. The designed phase-only holograms were fabricated on the silica substrate to obtain the diffraction optical element (DOE). Expect for one DOE, three lasers, and one CCD, no additional optical components are required to prompt a compact and simple experimental setup, which is expected to be used to realize full-color display.

optics
Practical method for dynamic color holographic display

Xianjun Peng,Yile Shi,Zhijun Ren,Yuchen Ying

DOI: https://doi.org/10.1364/AO.471751

2022-11-01

Abstract:A practical method for dynamic color holographic display by using a computer-generated hologram (CGH) with a high space-bandwidth product is proposed, and a dynamic color holographic display system is designed by a space-division method. First, three primary color CGHs of different frames from a color movie are fabricated on holographic recording material by a self-made CGH microfilming system. Secondly, the CGH is fixed on an X-Y moving stage, which is controlled by the system in order to bring the CGH to the appointed position. Thirdly, three primary color lasers are used to reconstruct the CGH. The switch of the lasers is controlled by the system synchronous with the X-Y moving stage. The color video with high quality can be obtained after filtering the three primary color reconstructed wavefronts. The experimental results demonstrate that the proposed dynamic color holographic display method is effective. It has practical application value in high-quality CGH display.
A Full-parallax Compact Three Dimensional Display System Based on Spliced View-field

Yi-fan PENG,Hai-fend LI,Xu LIU,Shuai LI

DOI: https://doi.org/10.3788/gzxb20114009.1405

2011-01-01

Abstract:A novel full-parallax 3D display approach and image generating algorithm are demonstrated. The display system employs a panel display monitor, an array of mini-projectors, a rear projecting light beam and a special orthogonal diffuser. Image generation program is operated based on OpenGL programming. In order to validate the proposed theory based on spliced view-field, a compact prototype-equipment with LCD, Fresnel lens, directional diffuser and rear projecting structure is proposed. The 3D images and dynamic videos displayed by the system can be observed at different horizontal and vertical viewpoints, with more compact size and better use experience.
15.2: Design and Realization of Full‐Color VHG Holographic Waveguide Display

Zhongwen Shen,Chuang Wang,Yishi Weng,Yuning Zhang

DOI: https://doi.org/10.1002/sdtp.15881

2022-10-01

SID Symposium Digest of Technical Papers

Abstract:To realize the chromatic display function of VHG holographic waveguide display system, we firstly study the preparation process and holographic peformance of color‐sensitive acrylate based photopolymer. Based on the prepared photopolymer, we fabricated the RGB holographic waveguide device with the multiwavelength laser exposure method. Thus, for verifying the display function of the prepared device , the chromatic holographic waveguide near‐eye display module using the LCoS projector engine was developed. The application potential of the color‐sensitive photopolymer in holographic waveguide was also demonstrated.
A 360-degree floating 3D display based on light field regeneration.

Xinxing Xia,Xu Liu,Haifeng Li,Zhenrong Zheng,Han Wang,Yifan Peng,Weidong Shen

DOI: https://doi.org/10.1364/OE.21.011237

IF: 3.8

2013-01-01

Optics Express

Abstract:Using light field reconstruction technique, we can display a floating 3D scene in the air, which is 360-degree surrounding viewable with correct occlusion effect. A high-frame-rate color projector and flat light field scanning screen are used in the system to create the light field of real 3D scene in the air above the spinning screen. The principle and display performance of this approach are investigated in this paper. The image synthesis method for all the surrounding viewpoints is analyzed, and the 3D spatial resolution and angular resolution of the common display zone are employed to evaluate display performance. The prototype is achieved and the real 3D color animation image has been presented vividly. The experimental results verified the representability of this method. (c) 2013 Optical Society of America
Color Holographic Display Based on Azo-Dye-doped Liquid Crystal (invited Paper)

Xiao Li,Chao Ping Chen,Yan Li,Xinhong Jiang,Hongjing Li,Wei Hu,Gufeng He,Jiangang Lu,Yikai Su

DOI: https://doi.org/10.3788/col201412.060003

IF: 2.56

2014-01-01

Chinese Optics Letters

Abstract:A multiplexed holographic display video has been achieved by using a passive azo-dye-doped liquid crystal (LC) cell. Holograms formed in this cell can be refreshed in the order of several milliseconds. By angular multiplexing technique, dynamically multiplexed holographic videos are realized. Moreover, the reconstructed RGB images are merged into a color image, which illustrates the possibility of a color holographic three-dimensional (3D) display by holographic multiplexing of the LC cell.

Lightweight Full-Color Holographic 3D Display System Based on Color Dispersion Compensation Method

Holographic three-dimensional display based on shifted Fraunhofer diffraction

Reproduction of a Computer-Generated Hologram with a White Light Source and Liquid Crystal Device

Binocular full-color holographic three-dimensional near eye display using a single SLM

Holographic Three-Dimensional Display Based on Optimizing Arrangement of Holograms

Holographic near-eye display system based on double-convergence light Gerchberg-Saxton algorithm.

Simply structured full-color holographic three-dimensional display using angular-compensating holographic optical element

Compact Full-Color Holographic 3-D Display Based on Undersampled Computer-Generated Holograms and Oblique Projection Imaging.

Ultrahigh-fidelity full-color holographic display via color-aware optimization

High-Quality Holographic 3D Display System Based on Virtual Splicing of Spatial Light Modulator

Convolutional Symmetric Compressed Look-Up-table Method for 360° Dynamic Color 3D Holographic Display.

Compact Lensless Full-Color Holographic Projection System with Digital Phase

Full-Color See-Through Three-Dimensional Display Method Based on Volume Holography

Color Virtual Display Based On Planar Waveguide With Transmission Volume Holograms

High-resolution Fresnel hologram information simplification and color 3D display

Crosstalk-Free Multiplane Full-Color Holography Based on the Space Division Method

Practical method for dynamic color holographic display

A Full-parallax Compact Three Dimensional Display System Based on Spliced View-field

15.2: Design and Realization of Full‐Color VHG Holographic Waveguide Display

A 360-degree floating 3D display based on light field regeneration.

Color Holographic Display Based on Azo-Dye-doped Liquid Crystal (invited Paper)