Abstract:Recent years have witnessed an increasing use of high strength aluminium alloys in structural applications, however, the mechanical properties of this type of materials are rather susceptible to elevated temperatures. This paper presents an experimental study on the mechanical properties of 7A04-T6 high strength aluminium alloy at elevated temperatures and after cooling down. Tensile coupon tests were first carried out on the specimens at high-temperature steady state conditions and post-fire conditions for temperatures ranging from 20 to 400 °C. The effect of cooling methods (cooled by air/water) was taken into account in the post-fire tests. Key mechanical properties, including Young’s modulus, yield strength, ultimate strength and ultimate strain, as well as the stress–strain responses obtained from both tests were fully reported and the microstructures of the post-fire material were examined. It is shown that the Young’s modulus and strengths decrease dramatically when temperatures are higher than 200 °C and the strengths decrease to less than 5% of the room temperature values at 400 °C, but a large proportion (up to 90%) of them regains after cooling down. In addition, the post-fire mechanical properties of the material exposed to 400 °C was found to be higher than those exposed to 300 °C; this was further explained through the microstructure examination. The test data were then utilised to assess the accuracy of existing codified design methods and the comparisons revealed that all of them provide inaccurate and scattered predictions. Finally, design formulae for the elevated-temperature retention factors as well as the post-fire residual factors and a two-stage Ramberg–Osgood material model were proposed. The design proposal was found to provide accurate predictions for the full-range stress–strain responses of the high strength aluminium alloy at both high-temperature steady state and post-fire conditions.

Experimental Method of Mechanical Melting Point in A6N01-T5 Aluminum Alloy

Research on Microstructure and Mechanical Properties of CMT and MIG Welded Joints of A6N01 Aluminum Alloy

New Approach for Modeling Flow Stress of Aluminum Alloy 6A10 Considering Temperature Variation

Mechanical properties of 7A04-T6 high strength structural aluminium alloy at elevated temperatures and after cooling down

Mechanical property tests and dynamic response analysis for 5A06 aluminum alloy plates subjected to underwater shock loading

Study of dynamic mechanical behavior of 1060-H112 aluminum alloy: Experimental and numerical simulation

Mechanical Properties of a Novel High-Strength Aluminum-Lithium Alloy

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

A Molecular Dynamics Study on Melting Point and Specific Heat of Ni3Al Alloy

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Effects of Solution Treatment Temperatures on Microstructure and Mechanical Properties of TIG–MIG Hybrid Arc Additive Manufactured 5356 Aluminum Alloy

TEM Microstructure, Mechanical Properties and Temperature Estimation in the 5XXX Series Al-Mg-Si Aluminum Alloy with W-Ni-Fe Tungsten Composite Friction-Welded Joints

Pulsed MIG welding of A6N01 Al alloy used in high-speed vehicle

A Forward Identification Method for High-Temperature Stress-Strain Curves of 7075 Aluminum Alloy Sheet Considering the Necking Stage

Dynamic Mechanical Behavior and Numerical Simulation of 6013-T4 Aluminum Alloy at Different Temperatures and Strain Rates

Dynamic Mechanical Behavior and Microstructural Evolution of the Al-6Mg Alloy Subjected to Three Treatment Conditions

Experimental investigation on the post-fire mechanical properties of structural aluminum alloys 6061-T6 and 7075-T73

Comparative Study of 5A06 Aluminum Alloy Welded Joints Obtained by Different Laser–Tungsten Inert Gas Hybrid Welding

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Effect of Novel Thermomechanical Treatment on Microstructure and Properties of 6156 Alloy

Establishment and Application of Material Models for Numerical Simulation of Welding Process