Abstract:Purpose – Rock-fill dams are embankments of compacted free-draining granular earth containing an impervious zone. Earth utilized in such dams often contains a high percentage of large particles – hence the term rock-fill. Mass stability of these dams results from friction and particle interactions rather than through a cementing agent binding the particles together. However, high-stress conditions and prolonged exposure to the elements can severely damage rock-fill. Therefore, understanding and modeling rock-fill breakage is important for dam engineering. The purpose of this paper is to improve discontinuous deformation analysis (DDA) techniques for modeling rock-fill breakage, proving the new method using simulations of spherical particle crushing. Design/methodology/approach – This work models rock-fill as bonded ellipsoid particles, and develops an improved DDA method to model the breakage of particle assemblies. The paper starts by describing the principles of three-dimensional DDA for spherical particles, and then derives the submatrices for normal contact, shear contact, and frictional force. The new algorithm incorporates a bond model with a revised open-close iteration algorithm into the DDA method to simulate particle crushing. To validate the improved DDA method, calculated particle contacts and movements are validated against theoretical results. Finally, this work performs a series of point-loading experimental tests for cement ellipsoid particles of both high and low compression strengths, with the test results compared against the results from corresponding DDA simulations. Findings – In particle crushing tests, the force and displacement show an approximately linear relationship until the crushing point, at which point low compression ellipsoid particles split into several large pieces while the high-compression particles break into many small fragments. The DDA simulation results are in good agreement with the crushing tests, demonstrating the validity of the DDA method for solving particle crushing problems. Although the improved DDA model is applicable to rock-fill particle crushing studies, some issues remain, particularly in increasing calculation efficiency and performing large-scale computations and long real-time simulations. Future research should address these issues. Originality/value – A bond model with a revised open-close iteration algorithm is incorporated into the DDA method. The simulated results shed insight into rock-fill crushing mechanisms, an element of concern in engineering practices.

Simulation of Crack Initiation and Propagation Using the Improved DDA

Improvement of DDA with a New Unified Tensile Fracture Model for Rock Fragmentation and its Application on Dynamic Seismic Landslides

Improved Discontinuous Deformation Analysis Method for Modeling Tensile Cracking in Quasi-Brittle Materials

Efficient Investigation of Rock Crack Propagation and Fracture Behaviors during Impact Fragmentation in Rockfalls Using Parallel DDA

Extended DDA with Rotation Remedies and Cohesive Crack Model for Simulation of the Dynamic Seismic Landslide

Modeling Rock Failure Using the Numerical Manifold Method Followed by the Discontinuous Deformation Analysis

A Cohesive Model-Based Nonlinear Discontinuous Deformation Analysis for Tensile Fracture in Geotechnical Materials

Discontinuous deformation analysis (DDA) simulations of crack propagation, branching and coalescence in brittle materials under dynamic loading

Development of Discontinuous Deformation Analysis with Displacement-Dependent Interface Shear Strength

An Improved Three-Dimensional Spherical DDA Model for Simulating Rock Failure

New Bond Model in Disk-Based DDA for Rock Failure Simulation

Simulation of the Nonlinear Mechanical Behaviors of Jointed Rock Masses Based on the Improved Discontinuous Deformation and Displacement Method

Investigations into the Rock Dynamic Response under Blasting Load by an Improved DDA Approach

Improved peridynamic model and its application to crack propagation in rocks

Particle Crushing Simulations with Improved Discontinuous Deformation Analysis

Towards Fully Automatic Modelling of the Fracture Process in Quasi-Brittle and Ductile Materials: a Unified Crack Growth Criterion

Experimental and numerical investigation of crack propagation and dynamic properties of rock in SHPB indirect tension test

Finite Element Modelling of Complex 3D Static and Dynamic Crack Propagation by Embedding Cohesive Elements in Abaqus

Modified discontinuous deformation analysis with mixed bilinear failure model for investigating quasi-brittle failure in geo-materials

Quantitative investigation of rock dynamic failure using Voronoi-based discontinuous deformation analysis

Damage mechanics challenge: Predictions from an adaptive finite element implementation of the stress-based phase-field fracture model