Preparation of ZnO quantum dots@SiO<sub>2</sub>/PVA for multifunctional coating on PET

Lei Ding,YiFan Chen,Zibo Hua,Li Liu,Haixu Chen,Zhengxiang Zhong,Yunzhe Du,Yudong Huang

DOI: https://doi.org/10.1039/c9nj05774a

IF: 3.3

2020-01-01

New Journal of Chemistry

Abstract:A durable, highly transparent and ultraviolet shielded inkjet printing coating was successfully prepared using ZnO QDs@SiO2.

What problem does this paper attempt to address?

Preparation of ZnO Quantum Dots@sio2/pva for Multifunctional Coating on PET

Lei Ding,Yifan Chen,Zibo Hua,Li Liu,Haixu Chen,Zhengxiang Zhong,Yunzhe Du,Yudong Huang

DOI: https://doi.org/10.1039/c9nj05774a

IF: 3.3

2020-01-01

New Journal of Chemistry

Abstract:ZnO quantum dots@SiO2 (ZnO QDs@SiO2) was synthesized by a modified sol-gel method, and then added to polyvinyl alcohol (PVA) to form an ink-absorbing coating with ultraviolet shielding performance on poly(ethylene terephthalate) (PET) films. A layer of silica encapsulated on the surface of ZnO QDs not only reduces the photocatalytic activity significantly, but also prevents the agglomeration of ZnO QDs in aqueous solution. The UV-vis transmittance spectrum of the as-prepared ink-absorbing coating displayed excellent shielding performance in the ultraviolet region (<355 nm) and high transmittance in the visible region. Even when exposed to 30 W ultraviolet for 100 h, no obvious changes were observed in its UV-vis transmittance spectrum, showing long-term durability. Notably, the ink absorption of the ink-absorbing coating prepared using ZnO QDs@SiO2 is higher than that of the ink-absorbing coating prepared using commercially available silica. Therefore, a durable, highly transparent and ultraviolet shielded inkjet printing coating on PET can be prepared with ZnO QDs@SiO2 nanoparticles.
A coating of silane modified silica nanoparticles on PET substrate film for inkjet printing

JiLi Wu,Lei Liu,Binbo Jiang,Zheng Hu,X. Q. Wang,Yudong Huang,Derong Lin,Qun Zhang

DOI: https://doi.org/10.1016/j.apsusc.2012.01.147

IF: 6.7

2012-01-01

Applied Surface Science

Abstract:The paper aims to design nanoporous coatings for inkjet printing and study its microstructure influence on the ink absorption. In the present work, two inkjet materials were prepared: one with unmodified nano-SiO 2 (S-1), the other with silica coupling agent modified nano-SiO 2 (S-2). The surface characteristic changing after modification was investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM). Wetting with contact angles was determined by the dynamic contact angle analysis test (DCAT). Through measurements, the dispersion of modified nano-SiO 2 particles in the coating was superior to the dispersion of unmodified nano-SiO 2 particles, surface roughness value (Ra) of S-1 was significantly higher than that of S-2, dynamic contact angle of S-2 is smaller than that of S-1 and ink droplet absorption in S-2 was much faster than in S-1. These results also reveal that the modification method is effective and offers a potential way to fabricate inkjet material with the advantages of microstructure and ink absorption over traditional methods. © 2011 Elsevier B.V. All rights reserved.
Facile Encapsulation of SiO2 on ZnO Quantum Dots and Its Application in Waterborne UV-shielding Polymer Coatings

Xiaolong Wang,Shuxue Zhou,Limin Wu

DOI: https://doi.org/10.1039/c3tc31479k

IF: 6.4

2013-01-01

Journal of Materials Chemistry C

Abstract:This paper presents a facile method for encapsulation of a SiO2 layer on the surfaces of ZnO quantum dots (ZnO QDs) to fabricate ZnO QD@SiO2 nanoparticles. Coating of a SiO2 layer can effectively improve the dispersion of ZnO QDs in an aqueous phase, insulate the photocatalytic activity of ZnO QDs and increase the photoluminescent quantum yield. When the as-obtained ZnO QD@SiO2 nanoparticles were introduced into acrylic latex, highly transparent, excellent UV-shielding and durable waterborne polymer coatings were easily fabricated. Moreover, the polymer coatings can convert UV into blue light effectively, which is beneficial for their application as agricultural films.
Preparation and Crystalline Properties of PET/ZnO Nano-meter Composite

包永忠,黄志明,翁志学

DOI: https://doi.org/10.3321/j.issn:1005-5770.2004.10.007

2004-01-01

Abstract:Poly(ethylene terephathalate)/ZnO(PET/ZnO)nano-meter composites were prepared by means of esterization and condensation reactions of terephathalic acid/ethyl glyol (TPA/EG)in the presence of nano-meter ZnO.The effects of the content and dispersion method of nano-meter ZnO on the viscosity average molecular weight of PET,the dispersion of nano-meter ZnO in the composite and the crystalline properties of PET were investigated.It was found that the introduction of nano-meter ZnO and poly(ethyl glycol)(PEG)dispersing agent to the reaction system had influence on the viscosity average molecular weight of PET.The direct dispersion of nano-meter ZnO in EG resulted in an aggregation of ZnO in PET,lowered the crystalline degree and rate of PET.Nano-meter ZnO particles dispersed well in the composite when PEG was added during the ZnO dispersion process,and the resulted PET had higher crystallization degree and rate.
Preparation of hyperbranched polyurethane acrylates and their properties in UV curable nano-SiO2 composite coatings for PET optical film

Kexin Zheng,Lixia Ling,Jianbing Wu,Baojun Wang

DOI: https://doi.org/10.1007/s10965-024-03922-8

IF: 3.061

2024-02-23

Journal of Polymer Research

Abstract:Polyethylene terephthalate (PET) films have been widely applied in the display industry. However, there is a problem in effectively protecting and extending the service life. To address this issue, a hyperbranched polyurethane acrylate (HPUA) has been synthesized with poly (hexylene glycol) neopentyl glycol ester (PNA), isophorone diisocyanate (IPDI), hyperbranched polyol Boltorn TM H2004 and pentaerythritol triacrylate (PETA). Further, a series of high-performance UV curable coatings have been prepared with HPUA, hollow nano-SiO 2 and silane coupling agents, along with other reagents. The structure of HPUA has been characterized by infrared spectroscopy (FT-IR), and the curing process has been monitored kinetically by real-time infrared spectroscopy to study its double-bond conversion ratio. The properties of the cured films have been investigated by thermogravimetric analysis (TGA). The water contact angle, aging and yellowing resistance, hardness, flexibility, abrasion resistance, light transmittance, and adhesion of the cured coatings on PET film have been tested. The results have shown that the addition of hollow nano-SiO 2 and silane coupling agents has not only not affect the light transmittance of the coatings but also improved the surface properties and heat resistance. When the silane coupling agent has been γ-Methacryloxypropyltrimethoxysilane (KH-570), the water contact angle of the coating has been 101.8°, excellent resistance to aging and yellowing, and the hardness, flexibility, and abrasion resistance have reached 89.4 HD, 3 mm, and 500 g/350 times, respectively. It was worth mentioning that the cured coating has shown excellent adhesion to PET film with the best overall performance. This work has offered important guidance for the protection of PET films.

polymer science
Preparation of strong adhesive waterborne coating on polyester fabric based on cation-π interaction and its application in oil/water separation

Alabati Aireken,Akram Yasin,Bin Hao,Peng-Cheng Ma

DOI: https://doi.org/10.1016/j.porgcoat.2023.107761

IF: 6.6

2023-06-19

Progress in Organic Coatings

Abstract:Polyethylene terephthalate (PET) is widely used in industry and daily life with its excellent mechanical and thermodynamic properties, and its surface property arising from coating has a great impact on its application. However, most coatings on PET display poor fastness and environmental pollution because of inactive surface and organic solvent . Encouraged by the cation-π interaction between the cationic and aromatic groups, we designed a strong adhesive waterborne polyurethane (PU) coating on PET fabric for oil/water separation. The bis(2-hydroxyethyl) dimethylammonium chloride (BDAC) in polymer not only provides PU with self-emulsification property, but also endows the coating with strong cation-π interaction with PET substrate. The effect of hydrophilic group on the property of PU dispersion was investigated by adjusting the content of BDAC. In addition, the interaction of optimized PU dispersion with single PET fiber was also quantitatively studied by adhesion force and surface tension measurements. It was demonstrated that the introduction of BDAC as cationic group resulted in a strong adhesion of PU coating on PET fabric and the coating could withstand various harsh environments. Furthermore, the synthesized coating could be used as an intermediate adhesive layer to anchor fumed SiO 2 on PET fabric, improving the surface roughness and hydrophobicity of the substrate. The modified fabric exhibited remarkable durability and excellent ability for oil/water separation.

materials science, coatings & films,chemistry, applied
ENHANCEMENT OF INK-RECEIVING PROPERTIES OF SIO2/PVA COMPOSITE FILMS BY USING RARE EARTH-MODIFIED SIO2 PARTICLES

Lu Shao,Chenzhong Mu,Yifeng Huang,Shangang Ding,Xiao Li,Yongping Bai,Yudong Huang

IF: 2.485

2011-01-01

Iranian Polymer Journal

Abstract:For the first time, rare earths were utilized to modify silica (SiO2) for improving the ink-receiving properties of silica/PVA (polyvinyl alcohol) composite films which was coated onto PET (polyethylene terephthalate) substrate. Fourier transform infrared spectra, XPS, scanning electron microscope, Brunauer-Emmett-Teller (BET) surface area measurement, contact angle and mechanical strength tests were used to characterize silica and SiO2/PVA composite films before and after modification by rare earths. The results indicated that the rare earths can effectively modify silica by increasing the oxygen-containing groups, decreasing the pore size and cumulative volume of pores, and narrowing the pore size distribution. The possible mechanism during rare earth-modification of silica may be due to the breakage of Si-O-C bonds which generates the carbon radicals combined with dissolved oxygen in the solution to form C-O/C-OH bonds. However, the detailed reaction mechanism still needs to be investigated and clarified in the future because of the complexity during the reaction. The characterization of SiO2/PVA films illustrates that silica content, compared to rare earth treatment time, has stronger effects on the hydrophilicity enhancement of the films. The tensile strength of SiO2/PVA films rapidly increased from 46.8 MPa to 72.6 MPa when increasing the rare earth treatment time from 0 to 10 h. The ink-receiving properties of SiO2/PVA films were thoroughly examined which illustrated that modification of SiO2 by rare earth up to 10 h can significantly enhance the ink-receiving properties of the composite films in terms of image quality, desiccation time of ink and mechanical strength of films with the optimum SiO2/PVA ratio of 0.3 (by weight). Besides, the thermal stability of composite films containing rare earth modified silica was excellent. Therefore, the SiO2/PVA composite films containing rare earth-modified silica seem to be promising materials for high-performance applications.
Protection of silica-coated ZnO nanoparticles on pre-dyed polyester fabrics against photofading

Mingwen Zhang,Bin Tang,Lu Sun,Xungai Wang

DOI: https://doi.org/10.1080/00405000.2016.1153912

IF: 1.7698

2017-01-01

Journal of the Textile Institute

Abstract:This work was designed to investigate the ability of silica-coated ZnO (ZnO&SiO2) nanoparticles (NPs) as ultraviolet (UV) absorbers for protecting pre-dyed polyester fabrics against photofading. Despite that ZnO NPs are excellent UV absorbers, their strong photocatalytic activity limits the application in UV protection. In this study, a silica layer was coated onto ZnO NPs to form a physical barrier between the ZnO and a polyester substrate, which allowed effective UV shielding while minimising the harmful effects of photocatalytic activity on the substrate. The structure and optical proprieties of ZnO&SiO2 NPs were observed. The bare ZnO and ZnO&SiO2 NPs were, respectively, applied to polyester fabrics coloured with three kinds of dyes by a dip coating method. The photofading level of treated fabrics after exposure under simulated sunlight was evaluated. The ZnO&SiO2 NPs exhibited excellent protection on pre-dyed polyester fabrics against photofading.
Preparation of a temperature-sensitive superhydrophobic self-cleaning SiO2-TiO2@PDMS coating with photocatalytic activity

Xuan Wang,Hao Ding,Sijia Sun,Han Zhang,Run Zhou,Yangzi Li,Yu Liang,Jie Wang

DOI: https://doi.org/10.1016/j.surfcoat.2021.126853

IF: 4.865

2021-02-01

Surface and Coatings Technology

Abstract:In this paper, SiO2-TiO2 composite particles were prepared by loading nano-TiO2 onto the surfaces of amorphous SiO2 microspheres, which were then modified with PDMS to obtain a SiO2-TiO2@PDMS ternary compound. The photocatalytic performance of SiO2-TiO2@PDMS and the wettability of the coated surface were tested and characterized. Moreover, the effect of microstructure and composition of SiO2-TiO2@PDMS on its properties was studied. The results showed that SiO2-TiO2@PDMS possessed a certain degree of photocatalytic activity and the coating was almost superhydrophobic. Furthermore, the wettability and adhesion to water droplets of the SiO2-TiO2@PDMS coating were affected by the heat-treatment temperature; the mechanism of the above phenomena was also analysed. Moreover, the as-prepared coating exhibited excellent repellent effects towards acid (pH = 2), alkaline (pH = 11), and organic dye droplets. A mechanically damaged coating maintained its liquid repellence, indicating that the good mechanical stability of the coating. The superhydrophobicity of the as-prepared coating did not decrease after UV irradiation for 8 h, illustrating that the as-prepared coating had a great UV irradiation resistance. In addition, the as-prepared coating was environmentally friendly and free of fluorides and is therefore suitable for practical applications.

physics, applied,materials science, coatings & films
Synthesis and performance of ZnO quantum dots water-based fluorescent ink for anti-counterfeiting applications

Xi Chen,Qi Wang,Xiao-Ju Wang,Jie Li,Guo-Bin Xu

DOI: https://doi.org/10.1038/s41598-021-85468-z

IF: 4.6

2021-03-12

Scientific Reports

Abstract:Abstract In this study, the ZnO quantum dots (QDs) water-based fluorescent anti-counterfeiting ink was prepared with the polyvinylpyrrolidone (PVP) content of 0.15–0.17 g/mL, the ZnO QDs concentration of 4% and water as the solvent, which has good fluorescence, printability and resistance. According to the halftone technology, fluorescence quenching of the ZnO QDs by acid, and acid resistance of the organic fluorescent ink, a high-quality anti-counterfeiting method of fluorescent discoloration was proposed. The QDs ink has broad application prospects in the field of anti-counterfeiting green packaging.

multidisciplinary sciences
Preparation and characterization of nanovoid core(TiO_2)/shell(SiO_2) nanoparticles immobilized PET fibers

WANG Wei,WANG Sheng,WANG Tao,XU Zhanglian,CHEN Wenxing

DOI: https://doi.org/10.3321/j.issn:0253-9721.2009.03.002

2009-01-01

Abstract:Nanovoid core(TiO_2)/shell(SiO_2) nanoparticles(SiO_2@@TiO_2) were prepared by sol-gel method successfully and characterized by TEM and EDS.High temperature sinter was adopted for removing organic substances from the nanoparticles which were then immobilized on PET fibers that had been subjected to alkali deweighting treatment.The protective ability of(SiO_2@@TiO_2) for the carrier and the capability of photodecomposition of formaldehyde of(SiO_2@@TiO_2/PET) were tested.The result indicated that this(SiO_2@@TiO_2/)PET could significantly photodecompose formaldehyde without any damage to the PET fibers,and the core/shell structure could effectively prevent the direct contact of TiO_2 with the organic carrier,thus protecting it from being corroded.
Fabrication of PVDF/TiO 2 @CQDs photocatalytic films by ink-jet printing for dye degradation under visible light

Zihan Tian,Shuhao Qin,Jingkui Yang,Xiao Wu,Jing Zhang,Jianxin Li,Hong Wang,Zhenyu Cui

DOI: https://doi.org/10.1016/j.apsusc.2024.160078

IF: 6.7

2024-04-14

Applied Surface Science

Abstract:PVDF/TiO 2 @CQDs hybrid photocatalytic thin films were prepared by ink-jet printing. The printing ink was prepared with the TiO 2 , TiO 2 (s)@CQDs (surface composite), and TiO 2 (i)@CQDs (situ doping) nanoparticles as precursors, respectively. Compared to TiO 2 (s)@CQDs, TiO 2 (i)@CQDs has a smaller particle size (about 10.01 nm) and a narrower particle size distribution (6∼14 nm), which can improve the photocatalytic effect while avoiding nozzle clogging. The PVDF/TiO 2 (i)@CQDs hybrid film exhibited a high degradation efficiency ( η ) of 93.71 % for Rhodamine B (RhB) within 150 min under visible light with a catalyst load of only 0.49 wt%. The reaction rate constant ( ks ) of the PVDF/TiO 2 (i)@CQDs film was about 4.3 times higher than that of the PVDF/TiO 2 (s)@CQDs film. The small particle size of this S-scheme TiO 2 (i)@CQDs heterostructure nanoparticle and the more effective contact interface formed between TiO 2 and carbon quantum dots (CQDs) further facilitated electron transfer and enhanced photoactivity. The firmly immobilized catalysts on the Polyvinylidene fluoride (PVDF) film substrate through Ti-F coordination bonds ensured the reusability and stability of the photocatalytic film (the η of RhB still reached 88.05 % after 10 consecutive cycles). This work provides a new strategy for the application of ink-jet printing technology in photocatalysis.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
PET Surface Modification with Inkjet-Printing Pd2+/Epoxy Resin Solution for Selective Electroless Copper Plating

Yuanming Chen,Jin Wang,Yuanzhang Su,Xiaohuang Zhuo,Yan Hong,Guoyun Zhou,Chong Wang,Shouxu Wang,Wei He,Yao Tang,Xinhong Su,Weihua Zhang,Yingguo Tao

DOI: https://doi.org/10.1021/acsaelm.1c00901

IF: 4.494

2022-01-01

ACS Applied Electronic Materials

Abstract:This article introduces a simple method to selectively fabricate conductive lines with good adhesion and outstanding electrical properties on the surface of the polyethylene terephthalate (PET) film with simple pre-treatment. The synthetic Pd2+ complex solution is selectively coated on the surface of PET to establish a bridging layer by an inkjet printing instrument. The bridging layer then catalyzes the electroless deposition of copper after plasma activation. The deposited copper coating and the bridging layer are characterized by X-ray photoelectron spectroscopy, atomic force microscopy, contact angle, and scanning electron microscopy. The results indicate that the bridging layer is activated and reformed into a network structure after air plasma treatment. The activated bridging layer effectively catalyzes the electroless deposition of copper. An even and compact surface is achieved in the as-prepared copper plating layer with 5B-level adhesion. In addition, the electrical resistivity of selectively deposited copper circuit is 2.26 mu Omega/cm, which is equivalent to 1.3 times of the bulk copper.
Aerosol-jet printing of nanowire networks of zinc octaethylporphyrin and its application in flexible photodetectors.

Feng-Xia Wang,Jian Lin,Wei-Bing Gu,Yong-Qiang Liu,Hao-Di Wu,Ge-Bo Pan

DOI: https://doi.org/10.1039/c3cc38996k

IF: 4.9

2013-01-01

Chemical Communications

Abstract:Nanowire networks of zinc octaethylporphyrin (ZnOEP) were printed using an aerosol-jet printer on a poly(ethylene terephthalate) (PET) flexible substrate. The prototype photodetector based on the as-printed network exhibited high photosensitivity, fast photoresponse, and excellent mechanical stability.
Colloidal Stable Quantum Dots Modified by Dual Functional Group Polymers for Inkjet Printing

Ting Han,Ye Yuan,Xiao Liang,Yang Zhang,Chuanxi Xiong,Lijie Dong

DOI: https://doi.org/10.1039/c7tc00452d

IF: 6.4

2017-01-01

Journal of Materials Chemistry C

Abstract:A new ligand was reported to effectively prepare water-dispersible QDs with remarkable colloidal stability for inkjet printing.
In Situ Inkjet Printing Strategy for Fabricating Perovskite Quantum Dot Patterns

Lifu Shi,Linghai Meng,Feng Jiang,Yong Ge,Fei Li,Xian‐gang Wu,Haizheng Zhong

DOI: https://doi.org/10.1002/adfm.201903648

IF: 19

2019-07-11

Advanced Functional Materials

Abstract:<p>Perovskite quantum dots are emerging as attractive materials for photonic and optoelectronic applications. Patterning is an important step to incorporate them into display, anti‐counterfeiting, and optical chip applications. In this work, an in situ inkjet printing strategy is demonstrated for fabricating perovskite quantum dots patterns by printing perovskite precursor solutions onto a polymeric layer. Importantly, this strategy can achieve bright photoluminescence with a quantum yield up to 80% and shows broad applicability to a variety of perovskites and polymers. Moreover, the as‐fabricated perovskite quantum dots patterns are composed of a microdisks array on the surface of polymeric layer. The size of these microdisks can be varied by adjusting the printing temperature. To demonstrate the potential use in display and advanced anti‐counterfeiting applications, color pixel patterns and 2D code pattern are fabricated by varying the precursor solutions. The combination of superior photoluminescence properties, simple process, and low cost makes the in situ inkjet printing strategy very promising for patterning perovskite quantum dots toward photonic integrations.</p>

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
PET Surface Modification with Inkjet-Printing Pd 2+ /Epoxy Resin Solution for Selective Electroless Copper Plating

Yuanming Chen,Jin Wang,Yuanzhang Su,Xiaohuang Zhuo,Yan Hong,Guoyun Zhou,Chong Wang,Shouxu Wang,Wei He,Yao Tang,Xinhong Su,Weihua Zhang,Yingguo Tao

DOI: https://doi.org/10.1021/acsaelm.1c00901

IF: 4.494

2022-01-04

ACS Applied Electronic Materials

Abstract:This article introduces a simple method to selectively fabricate conductive lines with good adhesion and outstanding electrical properties on the surface of the polyethylene terephthalate (PET) film with simple pre-treatment. The synthetic Pd2+ complex solution is selectively coated on the surface of PET to establish a bridging layer by an inkjet printing instrument. The bridging layer then catalyzes the electroless deposition of copper after plasma activation. The deposited copper coating and the bridging layer are characterized by X-ray photoelectron spectroscopy, atomic force microscopy, contact angle, and scanning electron microscopy. The results indicate that the bridging layer is activated and reformed into a network structure after air plasma treatment. The activated bridging layer effectively catalyzes the electroless deposition of copper. An even and compact surface is achieved in the as-prepared copper plating layer with 5B-level adhesion. In addition, the electrical resistivity of selectively deposited copper circuit is 2.26 μΩ/cm, which is equivalent to 1.3 times of the bulk copper.

materials science, multidisciplinary,engineering, electrical & electronic
Crystallization Behavior and Uv-Protection Property of Pet-Zno Nanocomposites Prepared by in Situ Polymerization

Junqing He,Wei Shao,Ling Zhang,Chao Deng,Chunzhong Li

DOI: https://doi.org/10.1002/app.30614

IF: 3

2009-01-01

Journal of Applied Polymer Science

Abstract:The aim of this study was to investigate the crystallization behavior and UV-protection property of polyethylene terephthalate (PET)-ZnO nanocomposits. PET-ZnO nanocomposites containing 0.5-3.0 wt % of ZnO were successfully synthesized by in situ polymerization. The Fourier transformed infrared (FTIR) spectroscopy indicated the silane coupling agent was anchored onto the surface of ZnO. Scanning electron microscope (SEM) images showed ZnO particles were dispersed homogeneously in PET matrix with amount of 0.5-1.0 wt %. Differential scanning calorimetry (DSC) results exhibited that the incorporation of ZnO into PET resulted in increase of the melting transition temperature (T m ) and crystallization temperature (T c ) of PET-ZnO nanocomposites. The crystallization behavior of PET and PET-ZnO nanocomposites was strongly affected by cooling rate. ZnO nanoparticles can act as an efficient nucleating agent to facilitate PET crystallization. UV-vis spectrophotometry showed that UV-ray transmittance of PET-ZnO nanocomposites decreased remarkably and reached the minimum value of 14.3% with 1.5 wt % of ZnO, compared with pure PET whose UV-ray transmittance was 84.5%. PET-ZnO nanocomposites exhibited better UV-protection property than pure PET, especially in the range of UVA.
Scalable Preparation of Superdurable, Self-Healing, and Biocompatible Superhydrophobic Poly(ethylene terephthalate) Fabrics

Xuan Zhou,Wudi Zhang,Shuqiang Peng,Zhixuan Zhao,Wenxin Chen,Xiaohong Ding,Lixin Wu,Zixiang Weng

DOI: https://doi.org/10.1021/acsami.4c17473

IF: 9.5

2024-12-13

ACS Applied Materials & Interfaces

Abstract:The chemical inertness of poly(ethylene terephthalate) (PET) fabrics poses challenges in achieving superhydrophobic coatings with durable adhesion on their surfaces. Conventional surface modification methods such as alkali etching and plasma etching typically compromise the favorable mechanical properties of PET. In this study, polydopamine (PDA) was utilized to functionalize the PET fabric nondestructively by creating robust and reactive hydroxyl and amine groups on its surface, which were...

materials science, multidisciplinary,nanoscience & nanotechnology
Poly(vinyl alcohol)-Modified Colloidal Silicon Nanoparticles for Flexible Screen Printing Inks and Anticounterfeiting Applications

Qian Zhang,Wanyin Ge,Xin Xie,Peng He,Honglei Yin

DOI: https://doi.org/10.1021/acsanm.3c05437

IF: 6.14

2024-01-23

ACS Applied Nano Materials

Abstract:Homogeneous colloidal silicon nanoparticles (Si NPs) were synthesized at ambient temperatures. With the incorporation of poly(vinyl alcohol) (PVA), the absolute photoluminescence quantum yield (APLQY) and photochromic stability of the fluorescent colloid (p-Si NPs) were significantly enhanced compared to Si NPs. In the absence of additional high-temperature treatments or doped fluorophores, colloid p-Si NPs exhibit blue-green luminescence under ultraviolet excitation. Subsequently, the highly dispersed p-Si NPs solution underwent heat treatment, resulting in a suitable viscosity for direct screen printing. The printed pattern appears transparent under natural light and blue-green under ultraviolet light, showing good invisibility. These patterns possess notable characteristics, including high adhesion, uniformity, stain resistance, and excellent stability. Consequently, they can be efficiently developed for anticounterfeiting labels and printing inks. Notably, the ink also has the characteristics of low toxicity and substantial biocompatibility, offering promising avenues for the synthesis and application of environmentally friendly benign nano anticounterfeiting ink.

materials science, multidisciplinary,nanoscience & nanotechnology

Preparation of ZnO quantum dots@SiO<sub>2</sub>/PVA for multifunctional coating on PET

Preparation of ZnO Quantum Dots@sio2/pva for Multifunctional Coating on PET

A coating of silane modified silica nanoparticles on PET substrate film for inkjet printing

Facile Encapsulation of SiO2 on ZnO Quantum Dots and Its Application in Waterborne UV-shielding Polymer Coatings

Preparation and Crystalline Properties of PET/ZnO Nano-meter Composite

Preparation of hyperbranched polyurethane acrylates and their properties in UV curable nano-SiO2 composite coatings for PET optical film

Preparation of strong adhesive waterborne coating on polyester fabric based on cation-π interaction and its application in oil/water separation

ENHANCEMENT OF INK-RECEIVING PROPERTIES OF SIO2/PVA COMPOSITE FILMS BY USING RARE EARTH-MODIFIED SIO2 PARTICLES

Protection of silica-coated ZnO nanoparticles on pre-dyed polyester fabrics against photofading

Preparation of a temperature-sensitive superhydrophobic self-cleaning SiO2-TiO2@PDMS coating with photocatalytic activity

Synthesis and performance of ZnO quantum dots water-based fluorescent ink for anti-counterfeiting applications

Preparation and characterization of nanovoid core(TiO_2)/shell(SiO_2) nanoparticles immobilized PET fibers

Fabrication of PVDF/TiO 2 @CQDs photocatalytic films by ink-jet printing for dye degradation under visible light

PET Surface Modification with Inkjet-Printing Pd2+/Epoxy Resin Solution for Selective Electroless Copper Plating

Aerosol-jet printing of nanowire networks of zinc octaethylporphyrin and its application in flexible photodetectors.

Colloidal Stable Quantum Dots Modified by Dual Functional Group Polymers for Inkjet Printing

In Situ Inkjet Printing Strategy for Fabricating Perovskite Quantum Dot Patterns

PET Surface Modification with Inkjet-Printing Pd 2+ /Epoxy Resin Solution for Selective Electroless Copper Plating

Crystallization Behavior and Uv-Protection Property of Pet-Zno Nanocomposites Prepared by in Situ Polymerization

Scalable Preparation of Superdurable, Self-Healing, and Biocompatible Superhydrophobic Poly(ethylene terephthalate) Fabrics

Poly(vinyl alcohol)-Modified Colloidal Silicon Nanoparticles for Flexible Screen Printing Inks and Anticounterfeiting Applications