Abstract:Purpose Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens. Design/methodology/approach This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature. Findings It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process. Originality/value 316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

Structural Design of FDM 3D Printer for Low-melting Alloy

Layout and Geometry Optimization Design for 3D Printing of Self-Supporting Structures

Development of a Fused Deposition Modeling System for Low Melting Temperature Metal Alloys

Direct 3D Printing of Low Melting Point Alloy Via Adhesion Mechanism

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Improvement and Experimental Explore on Coordinated Control of Kinematic Mechanism of FDM 3D Printer

Alloy design against the solidification cracking in fusion additive manufacturing: an application to a FeCrAl alloy

Process window identification for 3D printing low melting point alloy (LMPA) using fused deposition modelling (FDM)

Alloy design for laser powder bed fusion additive manufacturing: a critical review

A Novel High-Efficiency Methodology for Metal Additive Manufacturing

Electric Field Assisted Direct Writing and 3D Printing of Low‐Melting Alloy

Microstructure evolution, phase formation, corrosion, and mechanical properties of stainless steel fabricated by extrusion-based sintering-assisted additive manufacturing

Developing Fused Deposition Modeling Additive Manufacturing Processing Strategies for Aluminum Alloy 7075: Sample Preparation and Metallographic Characterization

Metallurgy and Solidification Microstructure Control of Fusion-Based Additive Manufacturing Fabricated Metallic Alloys: A Review

Additive manufacturing of 316L stainless-steel structures using fused filament fabrication technology: mechanical and geometric properties

Study on Metal Deposit in the Fused-coating Based Additive Manufacturing☆

A multi-scale constitutive model for AlSi10Mg alloy fabricated via laser powder bed fusion

Liquid Phase 3D Printing for Quickly Manufacturing Metal Objects with Low Melting Point Alloy Ink

Mechanical and Thermal Analyses of Metal-PLA Components Fabricated by Metal Material Extrusion

Fundamental Study Of Fused-Coating Based Metal Additive Manufacturing

Design and Analysis of Fused Deposition Modeling 3D Printer Nozzle for Color Mixing