Li2CO3-free Li–O2/CO2 battery with peroxide discharge product

Yu Qiao,Jin Yi,Shaohua Guo,Yang Sun,Shichao Wu,Xizheng Liu,Sixie Yang,Ping He,Haoshen Zhou

DOI: https://doi.org/10.1039/c7ee03341a

2018-01-01

Abstract:We demonstrate that a Li–O2/CO2 battery cycles via formation of peroxodicarbonate (C2O62−) but not Li2CO3, and operates with a low charge potential of 3.5 V.

What problem does this paper attempt to address?

Li2CO3-free Li-O-2/CO2 Battery with Peroxide Discharge Product

Yu Qiao,Jin Yi,Shaohua Guo,Yang Sun,Shichao Wu,Xizheng Liu,Sixie Yang,Ping He,Haoshen Zhou

DOI: https://doi.org/10.1039/c7ee03341a

IF: 32.5

2018-01-01

Energy & Environmental Science

Abstract:Owing to the exceptionally high energy potential of lithium-oxygen chemistry, lithium-air batteries have received much attention as appealing alternatives to current state-of-art lithium ion batteries. However, owing to the presence of non-O-2 components in ambient air, the practical performance of Li-air batteries is limited to only a few cycles with low energy efficiency. In particular, when CO2 is incorporated into the battery system, Li2CO3 is formed during discharging, which results in serious climbing of the charge potential and subsequent decomposition of the cell components. Herein, by introducing an appropriate electrolyte into an aggregated contact ion pair (CIP) structure, we demonstrate a Li-O-2/CO2 battery, via formation of stabilized peroxodicarbonate (C2O62-) rather than Li2CO3 in the electrolyte, that operates with a very low charge potential (3.5 V). We anticipate that this discovery will provide a rational design strategy for modifying the reaction pathway of Li-O-2/CO2 battery and accelerating the evolution of Li-O-2 batteries to Li-air batteries.
In Situ Observation of the Electrochemical Behavior of Li–CO2/O2 Batteries in an Environmental Transmission Electron Microscope

Peng Jia,Yunna Guo,Dongliang Chen,Jingming Yao,Xuedong Zhang,Jianguo Lu,Yuqing Qiao,Liqiang Zhang

DOI: https://doi.org/10.1002/cey2.424

2024-01-01

Carbon Energy

Abstract:Li-CO2/O-2 batteries, a promising energy storage technology, not only provide ultrahigh discharge capacity but also capture CO2 and turn it into renewable energy. Their electrochemical reaction pathways' ambiguity, however, creates a hurdle for their practical application. This study used copper selenide (CuSe) nanosheets as the air cathode medium in an environmental transmission electron microscope to in situ study Li-CO2/O-2 (mix CO2 as well as O-2 at a volume ratio of 1:1) and Li-O-2 batteries as well as Li-CO2 batteries. Primary discharge reactions take place successively in the Li-CO2/O-2-CuSe nanobattery: (I) 4Li(+) + O-2 + 4e(-) -> 2Li(2)O; (II) Li2O + CO2 -> Li2CO3. The charge reaction proceeded via (III) 2Li(2)CO(3) -> 4Li(+) + 2CO(2) + O-2 + 4e(-). However, Li-O-2 and Li-CO2 nanobatteries showed poor cycling stability, suggesting the difficulty in the direct decomposition of the discharge product. The fluctuations of the Li-CO2/O-2 battery's electrochemistry were also shown to depend heavily on O-2. The CuSe-based Li-CO2/O-2 battery showed exceptional electrochemical performance. The Li-CO2/O-2 battery offered a discharge capacity apex of 15,492 mAh g(-1) and stable cycling 60 times at 100 mA g(-1). Our research offers crucial insight into the electrochemical behavior of Li-CO2/O-2, Li-O-2, and Li-CO2 nanobatteries, which may help the creation of high-performance Li-CO2/O-2 batteries for energy storage applications.
Enabling Stable Cycling of 4.2 V High‐Voltage All‐Solid‐State Batteries with PEO‐Based Solid Electrolyte

Jiliang Qiu,Xinyu Liu,Rusong Chen,Qinghao Li,Yi Wang,Penghao Chen,Luyu Gan,Sang‐Jun Lee,Dennis Nordlund,Yijin Liu,Xiqian Yu,Xuedong Bai,Hong Li,Liquan Chen

DOI: https://doi.org/10.1002/adfm.201909392

IF: 19

2020-04-06

Advanced Functional Materials

Abstract:Poly(ethylene oxide) (PEO)‐based solid electrolytes are expected to be exploited in solid‐state batteries with high safety. Its narrow electrochemical window, however, limits the potential for high voltage and high energy density applications. Herein the electrochemical oxidation behavior of PEO and the failure mechanisms of LiCoO2‐PEO solid‐state batteries are studied. It is found that although for pure PEO it starts to oxidize at a voltage of above 3.9 V versus Li/Li+, the decomposition products have appropriate Li+ conductivity that unexpectedly form a relatively stable cathode electrolyte interphase (CEI) layer at the PEO and electrode interface. The performance degradation of the LiCoO2‐PEO battery originates from the strong oxidizing ability of LiCoO2 after delithiation at high voltages, which accelerates the decomposition of PEO and drives the self‐oxygen‐release of LiCoO2, leading to the unceasing growth of CEI and the destruction of the LiCoO2 surface. When LiCoO2 is well coated or a stable cathode LiMn0.7Fe0.3PO4 is used, a substantially improved electrochemical performance can be achieved, with 88.6% capacity retention after 50 cycles for Li1.4Al0.4Ti1.6(PO4)3 coated LiCoO2 and 90.3% capacity retention after 100 cycles for LiMn0.7Fe0.3PO4. The results suggest that, when paired with stable cathodes, the PEO‐based solid polymer electrolytes could be compatible with high voltage operation.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
A Novel Three-Dimensional Cathode with Stable Long Cycling Performance for Lithium Oxygen Batteries

Tong Wang,Peng Zhang,Xu Wang,Qi Chen,Miao Wang

DOI: https://doi.org/10.1016/j.jelechem.2018.10.033

IF: 4.598

2018-01-01

Journal of Electroanalytical Chemistry

Abstract:Non-aqueous Li-O-2 battery has attracted plenty of interest due to its super theoretical energy density. Nevertheless, it also faces formidable challenges with respect to an unaccepted overpotential during charge process and a low round trip efficiency, which leads to a poor cycle life. Herein, we present a novel binder-free composite cathode comprised of MgCo2O4@3D graphene with a three-dimensional structure, which has never been used in the lithium oxygen batteries, as a cathode applied in the non-aqueous Li-O-2 battery. The MgCo2O4 nanowires as the catalyst is grown on the graphene substrate supported by the nickel foam. The discharge product Li2O2 formed with a flake-like morphology decompose at a low potential ascribed to excellent catalytic activity from MgCo2O4. Finally, we demonstrate a non-aqueous Li-O-2 battery capable of operating over 480 cycles with limiting capacity and rate values at 400 mAhg(-1) and 200 mAg(-1).
Stable 2e−/2CO2 Electrochemistry Triggered by Enriched Interfacial Oxygen Mo2N@Ti3C2O2 Elcetrocatalyst for High Rates and High Energy Efficiency Li‐CO2 Batteries

Ruixin Zheng,Mengmeng Yang,Xiaoqi Zhu,Qisheng Fang,Xilin Wang,Pengyang Lei,Jingwen Zhou,Bin Wang,Jianli Cheng

DOI: https://doi.org/10.1002/adfm.202412999

IF: 19

2024-09-13

Advanced Functional Materials

Abstract:A stable lithium oxalate (Li2C2O4) electrochemistry involving a 2e−/2CO2 process triggered by Mo2N@Ti3C2O2 electrocatalyst is proposed for Li‐CO2 batteries. The presence of enriched ‐O terminations between Mo2N and Ti3C2O2 strengthens charge redistribution of Mo and enhances the coupling between Mo 3d orbitals and O 2p orbitals in Li2C2O4, enabling the stable formation of Li2C2O4 during discharge. Rechargeable lithium‐carbon dioxide (Li‐CO2) batteries present a compelling strategy for carbon capture and utilization techniques. Nevertheless, the formation of Li2CO3 as the main discharge product in the 4e−/3CO2 electrochemistry of Li‐CO2 batteries necessitates an elevated applied voltage to achieve full decomposition, which leads to severe performance issues in Li‐CO2 batteries. In this work, a stable lithium oxalate (Li2C2O4) electrochemistry involving a 2e−/2CO2 process triggered by Mo2N@Ti3C2O2 electrocatalyst is proposed, which facilitates highly reversible redox reactions in Li‐CO2 batteries. The presence of enriched ‐O terminations at the interface between Mo2N and Ti3C2O2 strengthens charge redistribution of Mo 3d orbital electron and enhances the coupling between Mo 3d orbitals and O 2p orbitals in Li2C2O4. The adsorption energy of Li2C2O4 on Mo2N@Ti3C2O2 surface and energy barrier for self‐disproportionation reaction of Li2C2O4 are further increased, enabling the stable Li2C2O4 electrochemistry. Therefore, the Mo2N@Ti3C2O2 based Li‐CO2 battery can produce Li2C2O4 discharge products even at a high discharge rate of 500 mA g−1 (ten times to previous studies) and during deep cycling processes. Due to the stable Li2C2O4 electrochemistry, Li‐CO2 batteries exhibit excellent electrochemical performance, including ultra‐low overpotential (0.55 V), ultra‐high energy efficiency (82.9%), and excellent cycling stability electrode (800 h).

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Evidence for lithium superoxide-like species in the discharge product of a Li-O2 battery

Junbing Yang,Dengyun Zhai,Hsien-Hau Wang,Kah Chun Lau,John A Schlueter,Peng Du,Deborah J Myers,Yang-Kook Sun,Larry A Curtiss,Khalil Amine

DOI: https://doi.org/10.1039/c3cp00069a

2013-03-21

Abstract:We report on the use of a petroleum coke-based activated carbon (AC) with very high surface area for a Li-O(2) battery cathode without the use of any additional metal catalysts. Electrochemical measurement in a tetra(ethylene) glycol dimethyl ether-lithium triflate (TEGDME-LiCF(3)SO(3)) electrolyte results in two voltage plateaus during charging at 3.2-3.5 and 4.2-4.3 V versus Li(+)/Li. Herein we present evidence from Raman and magnetic measurements that the lower plateau corresponds to a form of lithium peroxide with superoxide-like properties characterized by a low temperature magnetic phase transition and a high O-O stretching frequency (1125 cm(-1)). The magnetic phase transition and the high O-O stretching frequency disappear when charged to above 3.7 V. Theoretical calculations indicate that a surface superoxide structure on lithium peroxide clusters and some lithium peroxide surfaces have an unpaired electron and a high O-O stretching frequency that help explain the observations. These results provide evidence that the form of the lithium peroxide discharge product is important to obtaining a low charge overpotential, and thus improving the round-trip efficiency between discharge and charge.
Gas Concentration-Driven LiOH Chemistry in Li-CO 2 Batteries

Linyue Li,Yang Wang,Binbin Dan,Shixuan Li,Zhoulu Wang,Di Wang,Xiang Liu

DOI: https://doi.org/10.1016/j.elecom.2024.107669

IF: 5.443

2024-01-26

Electrochemistry Communications

Abstract:In conventional Li-CO 2 batteries, Li 2 CO 3 is an intractable discharge product due to its wide bandgap. To this end, researchers have focused more attention on the decomposition of Li 2 CO 3 in order to reduce the high charge potential. However, even the kinetics of CO 2 evolution process can be accelerated, Li 2 CO 3 will still passivate the cathodes, which in turn affects the cycle life of Li-CO 2 batteries. Here, we designed a CO 2 partly-absent Li-CO 2 battery, the concentration of CO 2 involved during the discharge process is reduced, then the discharge potential of this battery can be moved to 2.1 V. Furthermore, the discharge product of this CO 2 partly-absent Li-CO 2 battery is proved to be LiOH instead of Li 2 CO 3 , it can be recharged at a low potential of 3.5 V benefit from the readily degradable product (LiOH). In this Li-CO 2 battery, the effect of gas concentration on discharge process is studied firstly, and totally different results are discussed, offering new insights into the material design and the development of reliable rechargeable Li-CO 2 batteries in the future.

electrochemistry
Co3O4-Catalyzed LiOH Chemistry in Li–O2 Batteries

Jingyu Lu,Sunita Dey,Israel Temprano,Yanting Jin,Chao Xu,Yuanlong Shao,Clare P. Grey

DOI: https://doi.org/10.1021/acsenergylett.0c01940

IF: 22

2020-01-01

ACS Energy Letters

Abstract:Li-O-2 batteries (LOBs) operating via LiOH chemistry have attracted increasing interest because of the higher stability of LiOH in organic electrolytes, compared to Li2O2. Several catalysts have been shown to promote the formation of LiOH during discharge. However, LiOH has been difficult to reoxidize to form oxygen on charging. Here, we report that, in the presence of water, Co3O4 promotes the formation of LiOH on discharge via a 4 e(-)/O-2 process with few side reactions, forming large (001) facet-exposed LiOH flakes. Hydroperoxide LiOOH was detected as a potential discharge intermediate. During charge, O-2 evolution was detected along with LiOH decomposition up to 3.9 V; at higher voltages, products from parasitic reactions can be detected. This work provides new insights into the role of solid catalysts in LiOH chemistry in LOBs, and will help promote the development of reversible and long-lasting LiOH-based LOBs.
Co 3 O 4 -Catalyzed LiOH Chemistry in Li–O 2 Batteries

Jingyu Lu,Sunita Dey,Israel Temprano,Yanting Jin,Chao Xu,Yuanlong Shao,Clare P. Grey

DOI: https://doi.org/10.1021/acsenergylett.0c01940

IF: 22

2020-11-09

ACS Energy Letters

Abstract:Li–O2 batteries (LOBs) operating via LiOH chemistry have attracted increasing interest because of the higher stability of LiOH in organic electrolytes, compared to Li2O2. Several catalysts have been shown to promote the formation of LiOH during discharge. However, LiOH has been difficult to reoxidize to form oxygen on charging. Here, we report that, in the presence of water, Co3O4 promotes the formation of LiOH on discharge via a 4 e–/O2 process with few side reactions, forming large (001) facet-exposed LiOH flakes. Hydroperoxide LiOOH was detected as a potential discharge intermediate. During charge, O2 evolution was detected along with LiOH decomposition up to 3.9 V; at higher voltages, products from parasitic reactions can be detected. This work provides new insights into the role of solid catalysts in LiOH chemistry in LOBs, and will help promote the development of reversible and long-lasting LiOH-based LOBs.This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry
Aqueous Formate‐Based Li‐CO 2 Battery with Low Charge Overpotential and High Working Voltage

Hairong Xue,Hao Gong,Xueyi Lu,Bin Gao,Tao Wang,Jianping He,Yusuke Yamauchi,Takayoshi Sasaki,Renzhi Ma

DOI: https://doi.org/10.1002/aenm.202101630

IF: 27.8

2021-07-28

Advanced Energy Materials

Abstract:Li-CO2 batteries (LCOBs) are considered to be an important strategy toward efficient carbon sequestration and energy storage. However, most typical discharge products (Li2CO3 and C) are insoluble and chemically stable, and require a high charge overpotential (≈3.5–4.5 V) to be decomposed. Herein, a novel aqueous LCOB with formic acid (HCOOH) as the discharge product is proposed. The soluble HCOOH can be directly utilized in the charge process without any further purification or compression, realizing a very facile electrochemical cycle. Nanoporous Pd films with a high electrochemical surface area exhibit a high bifunctional performance toward both CO2 reduction and formic acid oxidation. Accordingly, the assembled LCOB achieves a high working potential plateau of 2.61 V whereas the charge potential is significantly lowered to 2.87 V, delivering the highest energy efficiency of 91%. The present work demonstrates a brand-new aqueous LCOB with HCOOH as the discharge product for utilizing CO2 as power source.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Clean Electrocatalysis in a Li2O2 Redox-Based Li–O2 Battery Built with a Hydrate-Melt Electrolyte

Shichao Wu,Yu Qiao,Sixie Yang,Jing Tang,Ping He,Haoshen Zhou

DOI: https://doi.org/10.1021/acscatal.7b02960

IF: 12.9

2018-01-01

ACS Catalysis

Abstract:The electrocatalysis of the oxygen reduction reaction and oxygen evolution reaction in nonaqueous Li-O-2 batteries suffers from severe side reactions and high charge potential. Herein, we design an unreported hydrate-melt Li-O-2 battery without use of an unstable organic solvent. Its redox reaction depends on the formation of Li2O2 in high yield (96%) and its full decomposition. The designed battery shows an ultralow charge potential of similar to 3.16 V, a high discharge capacity of 38 mAh cm(-2), and stable cycling ability. After careful comparison of the discharge and charge products by XRD, SEM, Raman, FTIR, NMR, and quantitative titration, the great improvement in performance is attributed to the efficient avoidance of side reactions related to organic solvent degradation, which may be the primary cause of the high charge potential in a nonaqueous Li-O-2 battery. These results should initiate a deep understanding of Li-O-2 batteries and indicate another strategy toward practical Li-air batteries with moisture-proof properties and high safety.
Cycling Li-O2 Batteries via LiOH Formation and Decomposition

Tao Liu,Michal Leskes,Wanjing Yu,Amy J. Moore,Lina Zhou,Paul M. Bayley,Gunwoo Kim,Clare P. Grey

DOI: https://doi.org/10.48550/arXiv.1805.03042

2018-05-08

Abstract:The rechargeable aprotic Li-air (O2) battery is a promising potential technology for next generation energy storage, but its practical realization still faces many challenges. In contrast to the standard Li-O2 cells, which cycle via the formation of Li2O2, we use a reduced graphene oxide electrode, the additive LiI, and the solvent dimethoxyethane to reversibly form/remove crystalline LiOH with particle sizes > 15 um during discharge/charge. This leads to high specific capacities, excellent energy efficiency (93.2%) with a voltage gap of only 0.2 V, and impressive rechargeability. The cells tolerate high concentrations of water, water being the dominant proton source for the LiOH; together with LiI it has a decisive impact on the chemical nature of the discharge product and battery performance.

Chemical Physics
Realizing stable carbonate electrolytes in Li–O2/CO2 batteries

Kai Chen,Jia‐Yi Du,Jin Wang,Dong‐Yue Yang,Jiang‐Wei Chu,Hao Chen,Hao‐Ran Zhang,Gang Huang,Xin‐Bo Zhang

DOI: https://doi.org/10.1002/cjoc.202200498

IF: 5.56

2022-10-07

Chinese Journal of Chemistry

Abstract:Comprehensive Summary The increasing demand for high‐energy storage systems has propelled the development of Li‐air batteries and Li‐O2/CO2 batteries to elucidate the mechanism and extend battery life. However, the high charge voltage of Li2CO3 accelerates the decomposition of traditional sulfone and ether electrolytes, thus adopting high‐voltage electrolytes in Li‐O2/CO2 batteries is vital to achieve a stable battery system. Herein, we adopt a commercial carbonate electrolyte to prove its excellent suitability in Li‐O2/CO2 batteries. The generated superoxide can be captured by CO2 to form less aggressive intermediates, stabilizing the carbonate electrolyte without reactive oxygen species induced decomposition. In addition, this electrolyte permits the Li metal plating/stripping with a significantly improved reversibility, enabling the possibility of using ultra‐thin Li anode. Benefiting from the good rechargeability of Li2CO3, less cathode passivation, and stabilized Li anode in carbonate electrolyte, the Li‐O2/CO2 battery demonstrates a long cycling lifetime of 167 cycles at 0.1 mA cm–2 and 0.25 mAh cm–2. This work paves a new avenue for optimizing carbonate‐based electrolytes for Li‐O2 and Li‐O2/CO2 batteries. This article is protected by copyright. All rights reserved.

chemistry, multidisciplinary
Compatible interface design of CoO-based Li-O2 battery cathodes with long-cycling stability

Chaoqun Shang,Shanmu Dong,Pu Hu,Jing Guan,Dongdong Xiao,Xiao Chen,Lixue Zhang,Lin Gu,Guanglei Cui,Liquan Chen

DOI: https://doi.org/10.1038/srep08335

2015-02-27

Abstract:Lithium-oxygen batteries with high theoretical energy densities have great potential. Recent studies have focused on different cathode architecture design to address poor cycling performance, while the impact of interface stability on cathode side has been barely reported. In this study, we introduce CoO mesoporous spheres into cathode, where the growth of crystalline discharge products (Li2O2) is directly observed on the CoO surface from aberration-corrected STEM. This CoO based cathode demonstrates more than 300 discharge/charge cycles with excessive lithium anode. Under deep discharge/charge, CoO cathode exhibited superior cycle performance than that of Co3O4 with similar nanostructure. This improved cycle performance can be ascribed to a more favorable adsorption configuration of Li2O2 intermediates (LiO2) on CoO surface, which is demonstrated through DFT calculation. The favorable adsorption of LiO2 plays an important role in the enhanced cycle performance, which reduced the contact of LiO2 to carbon materials and further alleviated the side reactions during charge process. This compatible interface design may provide an effective approach in protecting carbon-based cathodes in metal-oxygen batteries.
Towards a stable Li-CO2 battery: The effects of CO2 to the Li metal anode

Feilong Qiu,Siyun Ren,Xiaowei Mu,Yijie Liu,Xueping Zhang,Ping He,Haoshen Zhou

DOI: https://doi.org/10.1016/j.ensm.2019.11.017

IF: 20.4

2020-01-01

Energy Storage Materials

Abstract:Rechargeable Li-CO2 batteries are very attractive energy storage devices because of their high theoretical energy density and unique CO2 capture capability. Unfortunately, Li metal anode is unstable to the widely used ethers-based electrolytes, and the related Coulombic efficiency is low. Here, in the ethers-based electrolyte, the effects of CO2 to the Li metal anode was studied. Using a porous electrode, the reduced CO2 will be replenished from outside upon cycling. We found that, sufficient CO2 contributed to the formation of stable solid electrolyte interface (SEI) layers and protected the Li metal anode from rapid consumption. Under a current density of 1.0 mA cm(-2), the Coulombic efficiency of Li metal reached 99.0% after 200 cycles. Our work helps the researchers better understand the effects of CO2 crossover on anode and also provides a promising method to develop a stable Li metal anode for Li-CO2 battery.
A high-energy-density and long-life lithium-ion battery via reversible oxide–peroxide conversion

Yu Qiao,Kezhu Jiang,Han Deng,Haoshen Zhou

DOI: https://doi.org/10.1038/s41929-019-0362-z

IF: 37.8

2019-10-07

Nature Catalysis

Abstract:Li–O2 batteries have received considerable attention owing to their high theoretical gravimetric energy densities. However, the sluggish kinetic barrier between gaseous O2 and solid products leads to severe polarized overpotenial. Besides, the gas-open cell architecture and cumbrous O2 storage accessories bring additional burdens on practical application. Here, by pre-embedding Li2O nanoparticles into an iridium–graphene catalytic host, we confine the O2-free reversible Li2O/Li2O2 interconversion within a sealed cell environment. After rationally controlling the depth of charge, the O2/superoxo-free charge capacity can be extended to 400 mAh g–1 (based on the entire cathodic loading mass), with only 0.12 V round-trip overpotential. Ultrastable rechargeability can be achieved for over 2,000 cycles with 99.5% coulombic efficiency. Moreover, matched with a silicon anode, the full-cell output gravimetric energy density can reach nearly 600 Wh kg–1 (based on the loading mass of both electrodes). This work shows that reversible oxide–peroxide conversion can be utilized for the development of high-energy-density sealed battery technologies.

chemistry, physical
Mnco2o4 Decorated Magneli Phase Titanium Oxide As A Carbon-Free Cathode for Li-O-2 Batteries

Xuecheng Cao,Zhihui Sun,Xiangjun Zheng,Jinghua Tian,Chao Jin,Ruizhi Yang,Fan Li,Ping He,Haoshen Zhou

DOI: https://doi.org/10.1039/c7ta06152h

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:Advanced cathode catalysts are crucial to the promotion of aprotic Li-O-2 batteries for practical applications. Carbon is usually used as a cathode catalyst, but it reacts with the discharge products (Li2O2, LiO2) to form an insulating layer of lithium carbonate and prevents further reaction. To resolve this issue, the development of non-carbon cathode catalysts is of great demand. Herein, for the first time, we designed and fabricated a MnCo2O4 (MCO) spinel oxide decorated Magneli phase Ti4O7 as a carbon-free cathode for Li-O-2 batteries. The sub-stoichiometric Ti4O7 oxide serves as an electronic conductive network. The MCO spinel oxide along with the synergistic effect between Ti4O7 and MCO facilitate the kinetics of both oxygen reduction and decomposition of Li2O2. Furthermore, uniform anchoring of MCO nanoparticles on Ti4O7 surface provides a stable lithium peroxide-cathode interface during the discharge/charge process. The resulting Ti4O7/MCO hybrid proves to be a highly effective cathode catalyst. The discharge/charge voltage gap of the Ti4O7/MCO hybrid is about 0.75 V, which is significantly lower than that of pure carbon, C + MCO and pristine Ti4O7 cathode. A high specific capacity (5400 mA h g(-1) at 100 mA g(-1)) and excellent cycling performance (100 cycles at a capacity of 500 mA h g(-1) under 200 mA g(-1)) were obtained for this hybrid. The high catalytic activity and durability renders the Ti4O7/MCO hybrid a highly promising carbon-free cathode for Li-O-2 batteries.
A Lithium–oxygen Battery Based on Lithium Superoxide

Jun Lu,Yun Jung Lee,Xiangyi Luo,Kah Chun Lau,Mohammad Asadi,Hsien-Hau Wang,Scott Brombosz,Jianguo Wen,Dengyun Zhai,Zonghai Chen,Dean J. Miller,Yo Sub Jeong,Jin-Bum Park,Zhigang Zak Fang,Bijandra Kumar,Amin Salehi-Khojin,Yang-Kook Sun,Larry A. Curtiss,Khalil Amine

DOI: https://doi.org/10.1038/nature16484

IF: 64.8

2016-01-01

Nature

Abstract:Lithium–oxygen batteries allow oxygen to be reduced at the battery’s cathode when a current is drawn; in present-day batteries, this results in formation of Li 2 O 2 , but it is now shown that another high energy density material, namely LiO 2 , with better electronic conduction can be used instead as the discharge product, if the electrode is decorated with iridium nanoparticles.
MOF-Derived CoSe2 Nanoparticles/Carbonized Melamine Foam as Catalytic Cathode Enabling Flexible Li-CO2 Batteries with High Energy Efficiency and Stable Cycling

Ke Wang,Limin Liu,Dongyu Liu,Yuantao Wei,Yanxia Liu,Xinqiang Wang,Andrey S Vasenko,Mingtao Li,Shujiang Ding,Chunhui Xiao,Hongge Pan

DOI: https://doi.org/10.1002/smll.202310530

IF: 13.3

Small

Abstract:Rechargeable aprotic Li-CO2 batteries have aroused worldwide interest owing to their environmentally friendly CO2 fixation ability and ultra-high specific energy density. However, its practical applications are impeded by the sluggish reaction kinetics and discharge product accumulation during cycling. Herein, a flexible composite electrode comprising CoSe2 nanoparticles embedded in 3D carbonized melamine foam (CoSe2/CMF) for Li-CO2 batteries is reported. The abundant CoSe2 clusters can not only facilitate CO2 reduction/evolution kinetics but also serve as Li2CO3 nucleation sites for homogeneous discharge product growth. The CoSe2/CMF-based Li-CO2 battery exhibits a large initial discharge capacity as high as 5.62 mAh cm-2 at 0.05 mA cm-2, a remarkably small voltage gap of 0.72 V, and an ultrahigh energy efficiency of 85.9% at 0.01 mA cm-2, surpassing most of the noble metal-based catalysts. Meanwhile, the battery demonstrates excellent cycling stability of 1620 h (162 cycles) at 0.02 mA cm-2 with an average overpotential of 0.98 V and energy efficiency of 85.4%. Theoretical investigations suggest that this outstanding performance is attributed to the suitable CO2/Li adsorption and low Li2CO3 decomposition energy. Moreover, flexible Li-CO2 pouch cell with CoSe2/CMF cathode displays stable power output under different bending deformations, showing promising potential in wearable electronic devices.
In-situ Modification of Ultrathin and Uniform Layer on LiCoO2 Particles for 4.2 V Poly(ethylene Oxide) Based Solid-State Lithium Batteries with Excellent Cycle Performance

Wei Feng,Jianling Li,Huirong Liu,Mingliang Zhao,Jianjian Zhong,Jiameng Feng

DOI: https://doi.org/10.1016/j.electacta.2022.140473

IF: 6.6

2022-01-01

Electrochimica Acta

Abstract:Poly(ethylene oxide) based polymer electrolytes(PEO-SPEs) suffer from a narrow electrochemical window and deliver poor electrochemical performance when coupling with 4.2 V cathode. This severely limits the scope of its application. Here, a combination of physical stirring and electrochemistry is used to form an ultrathin and uniform cladding layer on the LiCoO2 particles. The results show that in addition to the decomposition of LiPO2F2 during the charge/discharge cycling, decomposition reactions occur during the stirring and drying process by Xray photoelectron spectroscopy (XPS), field emission scanning electron microscope (FESEM) and transmission electron microscope (TEM). This novel method effectively improves the electrochemical performance of 4.2 V PEO based solid-state lithium batteries. In particular, the cell shows excellent and stable electrochemical performance, exhibiting a discharge capacity of 112.0 mAh g(-1) after 200 cycles, a capacity retention rate of 79.4% and a capacity decay rate of approximately 0.1% per cycle when the surface of LiCoO2 is coated with 2 wt% LiPO2F2. In comparison, the discharge capacity of the unmodified LiCoO2 cathode is found to be only 75.6 mAh g(-1) after 100 cycles, with a poor capacity retention rate of 56.8%. Based on the basis of the above research, a new process was explored and also shows excellent interfacial stability by dispersing LiPO2F2 directly inside the binder which with a discharge capacity of 109.2 mAh g(-1) and a capacity retention rate of 84.5% after 145 cycles. This novel approach opens up a new pathway for solving the problem of interfacial stability between PEO based polymer electrolytes and high-voltage cathode.

Li<sub>2</sub>CO<sub>3</sub>-free Li–O<sub>2</sub>/CO<sub>2</sub> battery with peroxide discharge product

Li2CO3-free Li-O-2/CO2 Battery with Peroxide Discharge Product

In Situ Observation of the Electrochemical Behavior of Li–CO2/O2 Batteries in an Environmental Transmission Electron Microscope

Enabling Stable Cycling of 4.2 V High‐Voltage All‐Solid‐State Batteries with PEO‐Based Solid Electrolyte

A Novel Three-Dimensional Cathode with Stable Long Cycling Performance for Lithium Oxygen Batteries

Stable 2e−/2CO2 Electrochemistry Triggered by Enriched Interfacial Oxygen Mo2N@Ti3C2O2 Elcetrocatalyst for High Rates and High Energy Efficiency Li‐CO2 Batteries

Evidence for lithium superoxide-like species in the discharge product of a Li-O2 battery

Gas Concentration-Driven LiOH Chemistry in Li-CO 2 Batteries

Co3O4-Catalyzed LiOH Chemistry in Li–O2 Batteries

Co 3 O 4 -Catalyzed LiOH Chemistry in Li–O 2 Batteries

Aqueous Formate‐Based Li‐CO 2 Battery with Low Charge Overpotential and High Working Voltage

Clean Electrocatalysis in a Li2O2 Redox-Based Li–O2 Battery Built with a Hydrate-Melt Electrolyte

Cycling Li-O2 Batteries via LiOH Formation and Decomposition

Realizing stable carbonate electrolytes in Li–O2/CO2 batteries

Compatible interface design of CoO-based Li-O2 battery cathodes with long-cycling stability

Towards a stable Li-CO<sub>2</sub> battery: The effects of CO<sub>2</sub> to the Li metal anode

A high-energy-density and long-life lithium-ion battery via reversible oxide–peroxide conversion

Mnco2o4 Decorated Magneli Phase Titanium Oxide As A Carbon-Free Cathode for Li-O-2 Batteries

A Lithium–oxygen Battery Based on Lithium Superoxide

MOF-Derived CoSe2 Nanoparticles/Carbonized Melamine Foam as Catalytic Cathode Enabling Flexible Li-CO2 Batteries with High Energy Efficiency and Stable Cycling

In-situ Modification of Ultrathin and Uniform Layer on LiCoO2 Particles for 4.2 V Poly(ethylene Oxide) Based Solid-State Lithium Batteries with Excellent Cycle Performance