Multi-Element Quantitative Analysis of Shale and Sandstone Based on Laser Induced Breakdown Spectroscopy
Mingxin Shi,Jian Wu,Di Wu,Jinghui Li,Yan Qiu,Xinyu Guo,Ying Zhou,Ziyuan Song,Minxin Chen
DOI: https://doi.org/10.3788/cjl231332
2024-01-01
Chinese Journal of Lasers
Abstract:Objective Shale oil is an important unconventional resource that has become a major development focus, Owing to the possible reserves of petroleum and natural gas, information from core samples, which mainly contain geochemical and mineralogical information, has attracteil increasing attention from geologists and energy enterprises, Conventional analytical methods for mineralogical analysis, including inductively coupled plasma optical emission or mass spectrometry (ICP-OES/MS), instrumental neutron activation analysis (INNA), and X-ray fluorescence (XRF), are unsuitable for the festu analysis of shale because of their slow analysis speed and limited detection range. Laser-induced breakdown spectroscopy (LIBS) is a novel analytical method for various materials that uses laser pulses focused on a sample to generate laser-produced plasma and spectral emissions, With the advantages of minimal sample preparation, remote analysis, microsample ablation, and high analytical speed, LIBS is an optional access method for analysis of cores. In this study, multi-element quantitative analysis of natural shale and sandstone samples is conducted using a micro-LIIS system. A standardized spectral preprocessing method is developed to reduce spectral uncertainty, and a model input parameter optimization process is established to prevent model overfitting while improving model prediction accuracy. A quantitative analysis of Si, Ca. Fe. Al, Mg. and other elements in the shales and sandstones is performed, and the average predicted root mean square error of most samples is less than 16. providing technical support for regular mineral component analysis and lithology identification of shales and sandstones. Methods Amicro-LIBS system was established in this study, consisting of a laser, spectrometer, timing synchronizer, computer. and optical microscope. The system used a nanosecond pulse laser to generate a laser beam that passes through a laser beam splitter and was sampled by a photodiode to detect the laser timing. The transmitted laser beam was introduced into an optical microscope, adjusted to be coaxial with the microsesope illumination light path through a laser mirror, and finally focused on the sample surface through a near infrared objective lens to generate plasma. Plastna emission was collected by a short-focus lens to an optical fiber and connected to a six-channel spectrometer for spectrum collection; the integration time was set to 1 ms. The laser pulse energy was adjusted to 30 ml, and the detection delay of the spectrometer was set to 800 ns. Before the spectrum acquisition, two laser shots were applied for pre-ablation to stabilize the pulse energy, and 10 accumulated spectra were collected and analyzed. Partial least spares regression was used for the data analysis. Results and Discussions Because of the variety, inhomogeneity, and complexity of the samples, it is necessary to perform spectral line preprocessing and characteristic spectral line identification of the extracted spectra before quantitative analysis. Therefore, this study establishes a set of spectral data pre-processing procedures. After spectral preprocessing, the average relative standard deviation of a single shale sample (R-single ) decreases from 32.50% to 14.53%, whereas the average R-single of the sandstone samples decreases from 56.01% to 33. 92%, Simultaneously, the spectral relative standard deviation RS-S between shale and sandstone samples is also reduced after spectral processing, proving that the spectral preprocessing process can significantly reduce spectral uncertainty and improve the precision of the quantitative analysis prodiction results. Based on the leave-one-out method, this study constructs a set of PLSR model input dataset parameter optimization processes. When the number of input spectra is fixed, the optimization parameters initially decrease, and then increase as the number of principal components increases. This is because lower principal components cause model underfitting and insufficient interpretation of the training set samples, and the RMSEC is too high. The number of principal components causes overfitting of the model, poor interpretation of the new prediction set, and a high RMSECV value. The PLSR model achieves the best performance only when an appropriate number is selected. Under the optimized parameters. R-2>0.95 and RMSEC<1% for most samples, indicating that the P.SR model can better achieve multi-element quantitative analysis of shale and sandstone. Conclusions To meet the demands of rapid quantitative determination of mineral element content in natural shale and satidstone samples, a microanalysis laser-induced breakilown spectroscopy system with automated analysis capabilities is developed to rapidly detect and analyze oil and gas shale and sandstone natural samples. A standard process for spectral data preprocessing is established. and the average relative standani deviation of shales is reduced from 32.50% to 14.53%, and from 56.01% to 33.92% for samdstones. This study proposes a quantitative analysis process based on partial least squares regression (PLSR) with Si. Ca. Fe, Al, and Mg quantitatively predicted. The R-2 value for most samples is 0.95, and the RMSEC and RMSEP values are lower than 1%. This study provides technical support for the rapid analysis of the mineral components in shale and sandstone samples. The proposed data pre- processing atid quantitative analysis is expected to become a technical standard for L.IBS analysck.