Abstract:Journal of Building Physics, Ahead of Print. The purpose of this paper is to obtain the optimal filling scheme for improving thermal performance of the prefabricated sintered hollow wallboard considering both summer and winter conditions, and achieve self-insulation. Effects of different measures of installing separated paperboard, filling Phase Change Material (PCM) and Thermal Insulation Material (TIM) in the prefabricated wallboard are studied by experiment and COMSOL numerical methods. Firstly, the paperboard is installed in the middle of all cavities to reduce convection heat transfer. The experiment results show that average peak heat flux of the exterior surface in the three test days decreases by 5.25 W/m2 after installing the separated paperboard. Secondly, different filling positions (inner, middle, and outer cavities) and different phase change temperatures (23°C–27°C, 28°C–32°C, and 33°C–37°C) are discussed by COMSOL numerical model in summer condition, and the model is verified by the experimental data. Results show that better scheme is PCM (28°C–32°C) filled in the middle cavities of the prefabricated wallboard, which can increase the delay time and the attenuation factor of interior surface temperature by 2.92 h and 13.66, respectively, compared with no filling scheme. Finally, based on the optimal PCM filling scheme, schemes filled with TIM in different position of other cavities are also analyzed to further improve thermal performance of the prefabricated wallboard throughout the year. Results show that PCM (28°C–32°C) filled in the middle cavities and TIM filled in inner cavities has better effect in summer, and TIM filled in both inner and outer cavities is much better in winter. The evaluation indicators of the two better schemes in summer and winter are compared comprehensively, and the difference is not obvious. The results can provide optimal filling scheme and theoretical guidance for improving thermal performance of the prefabricated sintered hollow wallboard in hot summer and cold winter climate.

Numerical Study on Improving the Thermal Insulation Performance of Hollow Blocks by Optimizing the Holes Configuration

Optimization of the Configuration of 290×140×90 Hollow Clay Bricks with 3-D Numerical Simulation by Finite Volume Method

NUMERICAL SIMULATION OF OPTIMIZING CONFIGURATION OF HOLLOW CALY BRICKS

Numerical Thermal Analysis of Applying Insulation Material to Holes in Hollow Brick Walls by the Finite-Volume Method

Numerical Thermal Optimization of the Configuration of Multi-Holed Clay Bricks Used for Constructing Building Walls by the Finite Volume Method

Energy Efficiency For Airtightness And Exterior Wall Insulation Of Passive Houses In Hot Summer And Cold Winter Zone Of China

Numerical simulation of concrete hollow bricks by the finite volume method

Optimum Insulation Thickness of External Walls by Integrating Indoor Moisture Buffering Effect: a Case Study in the Hot-Summer-cold-winter Zone of China

3D Numerical Thermal Optimization of the Roofs Constructed with Cast-in-situ Hollow Concrete Floor System by Finite Volume Method

Design and thermal performance analysis of self-insulation concrete compound blocks

Thermal Performances Assessment and Improvement of Hollow Concrete Blocks Commonly Used in Morocco: Experimental and Numerical Approach

Numerical study for influence of exterior insulation on equivalent thermal conductivity of hollow brick walls

Configuration and Pyrological Performance of Self Thermal Insulating Blocks

Study on Temperature Cracks in the Concrete Hollow Pint-sized Block Buildings

Research on Site Tracing Monitoring of Temperature Field of Concrete Small Hollow Block Building

Optimization of Pass Design of Bidirectional Thermal-Insulation Bricks

Research on Crack-Resisting Construction Design Method of Concrete Small Cavity Block Building Based on Temperature Effect

The Method of Reducing Heat Loss from Thermal Bridges in Residential Buildings with Internal Insulation in the Hot Summer and Cold Winter Zone of China

THERMODYNAMIC PERFORMANCE TESTS FOR MATERIALS OF SELF-THERMALINSULATION WALLS IN HOT-SUMMER AND COLD-WINTER AREA

Structural Optimization and Application Research of Alkali-Activated Slag Ceramsite Compound Insulation Block Based on Finite Element Method

Research on improving thermal performance of prefabricated sintered hollow wallboard with optimizing filling materials