Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

Hydrothermally-assisted Co-Precipitation and Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material

Enhancing the High-Voltage Electrochemical Performance of the LiNi0.5Co0.2Mn0.3O2 Cathode Materials Via Hydrothermal Lithiation

Enhanced Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Materials Obtained by Atomization Co-Precipitation Method

Preparation and Electrochemical Properties of LiNi<sub>2/3</sub>Co<sub>1/6</sub>Mn<sub>1/6</sub>O<sub>2</sub> Cathode Material for Lithium-Ion Batteries

Synthesis of cathode material LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 and its electrochemical performances

Preparation and Electrochemical Properties of LiNi2/3Co1/6Mn1/6O2 Cathode Material for Lithium-Ion Batteries

Synthesis and Electrochemical Properties of Li[Ni X Co Y Mn 1− X − Y ]O 2 ( X, Y = 2/8, 3/8) Cathode Materials for Lithium Ion Batteries

Ultrasonic-assisted co-precipitation to synthesize lithium-rich cathode Li 1.3 Ni 0.21 Mn 0.64 O 2+ d materials for lithium-ion batteries

High capacity 0.5Li2MnO3·0.5LiNi 0.33Co0.33Mn0.33O2 cathode material via a fast co-precipitation method

Oxalate Co-Precipitation Synthesis of LiNi0.6Co0.2Mn0.2O2 for Low-Cost and High-Energy Lithium-Ion Batteries

Electrochemical Performance of Layer-Structured Ni0.8Co0.1Mn0.1O2 Cathode Active Materials Synthesized by Carbonate Co-Precipitation

Synthesis of LiNi0.6Co0.2Mn0.2O2 Cathode Material by a Carbonate Co-Precipitation Method and Its Electrochemical Characterization

High Rate Performances of the Cathode Material Lini1/3co1/3mn1/3o2 Synthesized Using Low Temperature Hydroxide Precipitation

A Facile and Novel Organic Coprecipitation Strategy to Prepare Layered Cathode Material Li[Li0.2mn0.54ni0.13co0.13]O-2 with High Capacity and Excellent Cycling Stability

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Effect of Precipitators on the Morphologies and Electrochemical Properties of Li1.2mn0.54ni0.13co0.13o2 Via Rapid Nucleation and Post-Solvothermal Method

Synthesis Of Layered Cathode Material 0.5li(2)Mno(3)Center Dot 0.5limn(1/3)Ni(1/3)Co(1/3)O(2) By An Improved Co-Precipitation Method For Lithium-Ion Battery

Improved solid-state synthesis and electrochemical properties of LiNi0.6Mn0.2Co0.2O2 cathode materials for lithium-ion batteries

Ammonia-low Coprecipitation Synthesis of Lithium Layered Oxide Cathode Material for High-Performance Battery

Synthesis of High Tap-Density Layered LiMn0.4 Ni0.4 Co0.2 O2 Cathode Material

Hydrothermal Synthesis and Electrochemical Performance of LiNi<sub>0.5</sub>Mn<sub>0.5</sub>O<sub>2</sub> as Lithium-Ion Battery Cathode