Abstract:The moisture content of corn kernel is generally 25%-40%when corn ear is harvested in China, which makes it not suitable for using direct way of threshing and harvesting. As an important part of harvesting, corn ear husking plays a great role in the harvest performance. At present, research on the performance of corn ear husker is commonly implemented by field experiments and bench tests. However, these approaches are restricted by the various kinds of corn and the shortage of harvesting time. Therefore, there are limitations on the test results. To deal with the problems mentioned above, a method combining theory analysis, virtual prototyping technology with high-speed photography was proposed in this paper to study the motion pattern of the corn ear on the husking device. First of all, to obtain the main influence factors of husking rate, efficiency and damage rate, the force and movement of corn ear in husking mechanism was analyzed in theory. Secondly, the three-dimensional (3D) model of husking mechanism was established using 3D design software, and then the 3D model was imported to ANSYS/LS-DYNA. After that the finite element model of corn ear and corn husker was set up by setting the material model and adding constraint and load. The velocity of corn ear in the direction of husking roller, the angular speed of corn ear around its own axis and the force of corn ear corresponding to the performance of the corn husker, were obtained by simulation analysis. The simulation results showed that the movement speed of corn ear along husking roller rose from 0.2 to 0.4 m/s with the increase of husking roller rotating speed;the angular velocity of corn ear ranged from 0 to 15 rad/s when the rotating speed of husking roller increased from 350 to 550 r/min;meanwhile, the force which was applied to corn ear increased and showed strong fluctuations, and the maximum stresses under three kinds of working conditions were about 11.9, 14.5 and 16.3 N, respectively. Finally, the husking test bench was built in the basis of the 3D model. The husking experiment was carried out with different rotating speeds of husking roller using high-speed photography. The test bench was made up of base frame, husking device, transmission mechanism, variable frequency motor (rated power of 3 kw), frequency converter, NI National Instruments data acquisition card, computer and high-speed photography (Phantom v9.1). The test condition was mainly consistent with the simulation condition. In order to avoid the influence of different sizes of corn ear, corn ear in the experiment was similar to that in the simulation in length and diameter size. At the same time, for reducing the influence of accidental factors on test results, the experiment was carried out three times. Taking the actual velocity and acceleration of corn ear in the direction of husking roller as validation arguments, the simulation data were compared with the high-speed photography test data. It was found that the simulation results agreed well with the actual results, which verified the validity and accuracy of the simulation model. The result also indicates that the simulation model could be a better alternative to the physical test, which can reduce the development cycle and the number of physical prototype test. The research output will play a significant role in carrying out the optimization design of the corn husker and provide a new method to develop a new husking mechanism.

&lt;i&gt;Research on motion Trajectory and Dynamic in Reciprocating Cutter of maize Stalk&lt;/i&gt;

Analysis And Experiment On Cutting Performances Of High-Stubble Maize Stalks

Optimization design of sliding cutting edge curve of corn rootstalk cutting tool

Optimization of cutting position and mode for cabbage harvesting

Theoretical Analysis and Multiscale Finite Element Simulation of the Dynamic Behavior of Maize Kernel Impact on Threshing Tooth

EFFECTS OF VARIOUS EDGE-CURVE TYPES AND ROTATIONAL SPEEDS OF DISC BLADES ON BREAKING FORCE AND ENERGY CONSUMPTION IN THE MAIZE STALK CHOPPING PROCESS

The Research of Kinematic Model and Cut Remainder in Line-contact Rotating-milling Conical Surface

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

The Study Of The Work Parameters Of The Corn Harvester Cutter

Motion Analysis and Simulation of the Drum Cutter of Cotton Top-cutting Machine

The Influence from the Abrasion of the Reciprocating Cuter to Triangle Area on Incise Diagram

Design and Experiment of Corn Low Damage Threshing Device Based on DEM

Dynamic Simulation and High-Speed Photography Experiment on Corn-Ear Husking

Simulation of a maize ear picking device with a longitudinal horizontal roller based on hypermesh modeling

Experimental Study on the Effect of Water Jet Cutting Parameters on Maize Stalks

A 3D simulation model of corn stubble cutting using finite element method

Design of a New Chopper for Corn Stalk and Wear Test of Its Moving Knives

Optimization Design and Experiment of Ear-Picking and Threshing Devices of Corn Plot Kernel Harvester

Performance of Waterjet on Cutting Maize Stalks: A Preliminary Investigation

DESIGN AND EXPERIMENT OF TRANSVERSE AXIAL FLOW CORN FLEXIBLE THRESHING DEVICE

Optimization Design of Cleaning Mechanism in Corn Thresher Based on MatLab

&amp;lt;i&amp;gt;Research on motion Trajectory and Dynamic in Reciprocating Cutter of maize Stalk&amp;lt;/i&amp;gt;