Abstract:"Burn-in" degradation occurs in many polymer solar cells, which dramatically reduces the overall power output of the cells at the early hundred hours. Understanding the "burn-in" degradation mechanism is therefore highly important to improve the lifetime of the cell. In this article, the decay behaviors of P3HT:PC61BM solar cells depending on the molecular weight of P3HT were systematically investigated. Although all of these P3HTs were highly crystalline with regioregularity of 94–97%, the stability of P3HT:PC61BM cells showed a nonmonotonic dependence on P3HT molecular weight. The cells based on P3HT with a weight average molecular weight (Mw) of 20 K showed much faster decadence in open circuit voltage (VOC) and fill factor (FF) during aging, yielding the lowest stability in comparison with that based on P3HT of 10, 25, and 30 K. UV–vis absorption and external quantum efficiency spectra demonstrated that the performance decay is not attributed to the change in the photoactive layer. The recovery of VOC and FF of the aged cells after renewing the MoO3/Al electrode revealed that the performance decay is mainly because of the interfacial degradation of P3HT:PC61BM/MoO3. Electron spin resonance spectroscopy and X-ray photoelectronic spectroscopy confirmed the photon-induced redox reaction between P3HT and MoO3 under light illumination, where P3HT is oxidized to the polaron and Mo(VI) was partially reduced to Mo(V). The photon chemical reduction (PCR) of MoO3 by P3HT is then ascribed as the essential reason for the fast VOC and FF decays of the cells during aging. The surface morphology of the photoactive layer measured by the atomic force microscope revealed the much rougher surface of the P3HT-20 K/PC61BM film. Such a rough surface increases the contact area between P3HT and MoO3, and consequently enhances the PCR of MoO3 and P3HT, which is considered as the main reason for the molecular weight-dependent degradation behaviors. For the first time, the current work clearly demonstrates that the photoreduction of the metal oxide and photoactive layer would lead to fast VOC and FF decays, which could be a very important degradation pathway for polymer solar cells.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01325?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01325</a>.J–V curves, EQE spectra, statistical data, FTPS and degradation curves of solar cells before and after aged, UV–vis spectra, XRD patterns, TEM images, ESR spectra, and XPS spectra of different films (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01325/suppl_file/ae0c01325_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

External load-dependent degradation of P3HT:PC<sub>61</sub>BM solar cells: behavior, mechanism, and method of suppression

External load-dependent degradation of P3HT:PC61BM solar cells: behavior, mechanism, and method of suppression

Comprehensive Understanding of Heat-Induced Degradation of Triple-Cation Mixed Halide Perovskite for a Robust Solar Cell

Revealing the Interfacial Photoreduction of MoO 3 with P3HT from the Molecular Weight-Dependent “Burn-In” Degradation of P3HT:PC 61 BM Solar Cells

Revealing the Interfacial Photoreduction of MoO3 with P3HT from the Molecular Weight-Dependent “Burn-In” Degradation of P3HT:PC61BM Solar Cells

Study on Permanent Deactivation of the Light-Induced Degradation in P-Type Compensated Crystalline Silicon Solar Cells

Thermally‐Induced Degradation in PM6:Y6‐Based Bulk Heterojunction Organic Solar Cells

Mechanisms and Suppression of Photoinduced Degradation in Perovskite Solar Cells

Probing the microscopic mechanisms in photovoltaic degradation behaviors of CH3NH3PbI3 perovskite films via photoconductive atomic force microscopy

Unraveling the Degradation Mechanisms of Perovskite Solar Cells under Mechanical Tensile Loads

Strong-bonding hole-transport layers reduce ultraviolet degradation of perovskite solar cells

An Efficient, “Burn in” Free Organic Solar Cell Employing a Nonfullerene Electron Acceptor

The Interplay of Stability between Donor and Acceptor Materials in a Fullerene‐Free Bulk Heterojunction Solar Cell Blend

Elucidating performance degradation mechanisms in non-fullerene acceptor solar cells

Electric‐Induced Degradation of Cathode Interface Layer in PM7:IT‐4F Polymer Solar Cells

Revealing degradation mechanisms in 3D/2D perovskite solar cells under photothermal accelerated ageing

Interfacial Degradation of Planar Lead Halide Perovskite Solar Cells

Photochemical Decomposition of Y‐Series Non‐Fullerene Acceptors Is Responsible for Degradation of High‐Efficiency Organic Solar Cells

The Interfacial Degradation Mechanism of Polymer:Fullerene Bis-Adduct Solar Cells and Their Stability Improvement

Brominated Polythiophene Reduces the Efficiency‐Stability‐Cost Gap of Organic and Quantum Dot Hybrid Solar Cells

Thermal-Induced Performance Decay of the State-of-the-Art Polymer: Non-Fullerene Solar Cells and the Method of Suppression