Enhanced photocatalytic oxygen evolution over Mo-doped Ca2NiWO6 perovskite photocatalyst under visible light irradiation

Ying Luo,Jiawei Xue,Xiaodi Zhu,Jose Daniel,Xiang Gao,Song Sun,Chen Gao,Jun Bao

DOI: https://doi.org/10.1039/c6ra26072a

IF: 4.036

2017-01-01

RSC Advances

Abstract:A series of Mo-doped Ca2NiWO6 (Ca2NiW1−xMoxO6, x = 0–0.05) was synthesized by a solid-state reaction.

What problem does this paper attempt to address?

Enhanced photocatalytic oxygen evolution over Mo-doped Ca2NiWO6 perovskite photocatalyst under visible light irradiation

Ying Luo,Jiawei Xue,Xiaodi Zhu,Jose Daniel,Xiang Gao,Song Sun,Chen Gao,Jun Bao

DOI: https://doi.org/10.1039/c6ra26072a

IF: 4.036

2017-01-01

RSC Advances

Abstract:A series of Mo-doped Ca2NiWO6 (Ca2NiW1-xMoxO6, x = 0-0.05) samples were synthesized by a solid-state reaction. The physical and optical properties of these photocatalysts were characterized by X-ray diffraction, X-ray absorption fine structure, UV-visible diffuse reflectance spectra, and the band structure along with density of states were calculated by the plane-wave-based density functional theory. The photocatalytic activity of oxygen evolution from water was evaluated under visible light irradiation. The Mo doping significantly increased the photocatalytic activity of Ca2NiWO6. The optimal Ca2NiW0.97Mo0.03O6 showed an oxygen evolution rate approximately 2 times higher than that of the pure Ca2NiWO6. The characterization results indicated that the Mo-doped Ca2NiWO6 maintained the double perovskite structure. The Mo6+ ions were substituted into the W6+ sites in the lattice, causing a certain amount of lattice distortion and promoting the formation of oxygen vacancies. Furthermore, the Mo doping introduced impurity energy levels into the band structure of Ca2NiWO6. Consequently, the conduction band changed from discrete to continuous and the bottom of the conduction band was shifted to more positive potential, compared to that of pure Ca2NiWO6, leading to a lower band gap and higher absorbance in the wider visible light region. These characteristics are responsible for the high photocatalytic activity of the oxygen evolution reaction.
Preparation of WOx-TiO2 and the Photocatalytic Activity under Visible Irradiation

Hai Yan Song,Hong Fu Jiang,Xing Qin Liu,Yin Zhu Jiang,Guang Yao Meng

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.1979

2007-01-01

Key Engineering Materials

Abstract:Nanocrystalline tungsten oxide doped titanium dioxide (WOx-TiO2) powders were prepared by TiCl4 hydrolysis and characterized by XRD, XPS, UV-Vis absorption spectra and TEM. Results showed that WO, not only hindered the growth of TiO2 particles but also greatly increased the transformation temperature (>800 degrees C) from anatase to rutile during sintering; the dominant fraction of tungsten oxides was non-stoichiometric tungsten oxide (WxOy) with Wn+ (4<n<6), which could easily substitute Ti4+ in the lattice of TiO2. The light absorption band of TiO2 changed from the near UV to the visible light range (2.68 eV in 1.0 %WOx-TiO2) because of the tungsten impurity energy level induced by WxTi1-xO2. The photocatalysis experiments demonstrated that the MB in aqueous solution was successfully degraded within 1h using WOx-TiO2 with an optimal WOx dosage of 1% under visible light irradiation.
(Mo+n) Codoped TiO2 for Enhanced Visible-Light Photoactivity

Hailin Liu,Zhihong Lu,Ling Yue,Jing Liu,Zhanghua Gan,Chang Shu,Ting Zhang,Jing Shi,Rui Xiong

DOI: https://doi.org/10.1016/j.apsusc.2011.05.085

IF: 6.7

2011-01-01

Applied Surface Science

Abstract:A series of Ti1-xMoxO2-yNy samples were prepared by using sol-gel method and characterized by X-ray diffraction, transmission electron microscopy and UV-vis absorption spectroscopy. All Ti1-xMoxO2-yNy samples are anatase phase. It is found that Mo, N mono-doping can increase visible light absorption, while (Mo + N) co-doping can greatly enhance absorption in whole visible region. Results of our first-principles band structure calculations reveal that (Mo + N)-doping, especially passivated co-doping can increase the up-limit of dopant concentration and create more impurity bands in the band gap of TiO2, which leads to a greatly increase of its visible-light absorption without a decrease of its redox potential. It reveals that (Mo + N) co-doped TiO2 is promising for a photocatalyst with high photocalystic activity under visible light. (C) 2011 Elsevier B.V. All rights reserved.
Highly Active NiO–CaO Photocatalyst for Degrading Organic Contaminants under Visible-Light Irradiation

Limin Song,Shujuan Zhang,Bin Chen,Donglan Sun

DOI: https://doi.org/10.1016/j.catcom.2008.08.032

IF: 3.51

2009-01-01

Catalysis Communications

Abstract:A series of NiO–CaO photocatalysts have been successfully prepared by a precipitation–calcination method. The specimen was characterized by powder X-ray diffraction and UV–vis diffuse reflectance spectra. The UV–vis diffuse reflectance spectra revealed that the NiO–CaO samples exhibited absorptions in a wide visible-light range of 400–600 and 700–800nm. These results showed that the NiO–CaO samples might possess excellent photocatalytic performances in the wide visible-light region. By using photocatalytic degrading methyl blue as the model reaction, the NiO–CaO samples showed higher photocatalytic activity than those of NiO, CaO, and commercial TiO2 under visible-light illumination.
A simple mechanical mixing method for preparation of visible-light-sensitive NiO-CaO composite photocatalysts with high photocatalytic activity.

Limin Song,Shujuan Zhang

DOI: https://doi.org/10.1016/j.jhazmat.2009.09.088

IF: 13.6

2010-01-01

Journal of Hazardous Materials

Abstract:Composite photocatalysts composed of NiO and CaO have been prepared via mechanically mixing of the two powders. The as-synthesized NiO–CaO products were characterized by X-ray diffraction (XRD) and UV–vis spectrometry. The experimental results showed that the absorption wavelength range of the mixed NiO–CaO sample was notably extended towards the visible-light region (400–450nm). Photocatalytic activity of the NiO–CaO composite was evaluated based on the decomposition of methylene blue under visible-light irradiation. The effects of CaO doping and the duration of heat treatment on the durability of the NiO–CaO products have been investigated in detail. Factors influencing photocatalytic activity and the mechanism of photocatalysis were also addressed.
A Novel Series of Photocatalysts M2.5VMoO8 (M = Mg, Zn) for O2 Evolution under Visible Light Irradiation

DF Wang,ZG Zou,JH Ye

DOI: https://doi.org/10.1016/j.cattod.2004.06.090

IF: 5.3

2004-01-01

Catalysis Today

Abstract:A new series of visible light-driven photocatalysts M2.5VMoO8 (M = Mg, Zn) crystallized in the orthorhombic crystal system were synthesized by a solid-state reaction method. The photophysical and photocatalytic properties of M2.5VMoO8 (M = Mg, Zn) under visible light irradiation were examined. It was found that efficient O2 was evolved from aqueous AgNO3 solution dispersed with the M2.5VMoO8 (M = Mg, Zn) powder samples synthesized under visible light irradiation. The electronic band structures of M2.5VMoO8 (M = Mg, Zn) were discussed in regard to the corresponding photocatalytic properties.
Carbonate doped Bi2MoO6 hierarchical nanostructure with enhanced transformation of active radicals for efficient photocatalytic removal of NO

Wangchen Huo,Weina Xu,Tong Cao,Ziyang Guo,Xiaoying Liu,Guangxu Ge,Nan Li,Tian Lan,Hong-Chang Yao,Yuxin Zhang,Fan Dong

DOI: https://doi.org/10.1016/j.jcis.2019.09.089

2019-12-01

Abstract:Doping heteroatoms in photocatalyst is an effective strategy to signally enhance the photocatalytic activity. Herein, we have favorably fabricated the carbonate doped Bi2MoO6 via a facile one-pot solvothermal method, which was verified by structure and constituent characterization analysis. In addition, the NO removal efficiency of carbonate-intercalated Bi2MoO6 is ~34%, far-exceeding that of the pure Bi2MoO6 (~13%), whilst exhibits a good stability and durability, owing to that the dopants could modulate the electron states of the Bi2MoO6, thus stimulating charge separation and migration, incenting transformation of reactive oxygen species and facilitating reactants activation, which are synthetically investigated by experimental characterization coupled with DFT calculation. Significantly, the in situ DRIFTS measurement was employed to dynamic monitor the NO oxidation process and clarify the photocatalytic mechanism under visible light irradiation. This work provides an efficient strategy to design photocatalysts with tunable motivating charge conversion and reactants activation towards NO photooxidation.
Microwave-assisted Synthesis of Mo-doped H1–xSr2Nb3–xMoxO10(x= 0, 0.05, 0.1, 0.15 and 0.2) with High Photocatalytic Activity

Xu Jing,Wei Yuelin,Huang Yunfang,Wang Jing,Chen A'xiang,Fan Leqing,Wu Jihuai

DOI: https://doi.org/10.1088/1674-4926/35/8/083001

2014-01-01

Abstract:H1–xSr2Nb3–xMoxO10 photocatalysts were synthesized using a microwave-irradiation-assisted ion-exchange reaction. The physicochemical properties of the photocatalysts were analyzed by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and ultraviolet—visible spectroscopy (UV—vis). The photocatalytic activity of the H1–xSr2Nb3–xMoxO10 was evaluated by degrading methyl orange (MO) dye under light irradiation from a 40-W mercury lamp. The results proved that the Mo doping amount had an important effect on the photocatalytic activity of the catalysts. The highest photocatalytic activity was obtained when the doping amount was 15 mol%. Furthermore, the complex preparation process and lengthy time was simplified and shortened greatly.
Cs-Doped WO3 with Enhanced Conduction Band for Efficient Photocatalytic Oxygen Evolution Reaction Driven by Long-Wavelength Visible Light

Dong Li,Siyu Tian,Qiuhua Qian,Caiyun Gao,Hongfang Shen,Fei Han

DOI: https://doi.org/10.3390/molecules29133126

IF: 4.6

2024-06-30

Molecules

Abstract:Cesium doped WO3 (Cs-WO3) photocatalyst with high and stable oxidation activity was successfully synthesized by a one-step hydrothermal method using Cs2CO3 as the doped metal ion source and tungstic acid (H2WO4) as the tungsten source. A series of analytical characterization tools and oxygen precipitation activity tests were used to compare the effects of different additions of Cs2CO3 on the crystal structure and microscopic morphologies. The UV-visible diffuse reflectance spectra (DRS) of Cs-doped material exhibited a significant red shift in the absorption edge with new shoulders appearing at 440-520 nm. The formation of an oxygen vacancy was confirmed in Cs-WO3 by the EPR signal, which can effectively regulate the electronic structure of the catalyst surface and contribute to improving the activity of the oxygen evolution reaction (OER). The photocatalytic OER results showed that the Cs-WO3-0.1 exhibited the optimal oxygen precipitation activity, reaching 58.28 µmol at 6 h, which was greater than six times higher than that of WO3-0 (9.76 μmol). It can be attributed to the synergistic effect of the increase in the conduction band position of Cs-WO3-0.1 (0.11 V) and oxygen vacancies compared to WO3-0, which accelerate the electron conduction rate and slow down the rapid compounding of photogenerated electrons-holes, improving the water-catalytic oxygen precipitation activity of WO3.
Effects of Mo Replacement on the Structure and Visible-Light-Induced Photocatalytic Performances of Bi2wo6 Photocatalyst

Liwu Zhang,Yi Man,Yongfa Zhu

DOI: https://doi.org/10.1021/cs200155z

IF: 12.9

2011-01-01

ACS Catalysis

Abstract:Phase-pure Bi2MoxW1-xO6 (0 <= x <= 1) photocatalysts were synthesized via a hydrothermal method. The as-prepared Bi2MoxW1-xO6 photocatalysts had an Aurivillius crystal structure and showed special anisotropic growth. The optical absorption spectra of Bi2MoxW1-xO6 were red-shifted monotonically as the value of x increased. On the basis of theoretical calculations, the introduction of Mo atom into Bi2WO6 could reduce the conduction band level of Bi2WO6, so the band gap energy was reduced. The curvature of the conduction band became smaller with an increase in the Mo content due to the different electronegativities of Mo 4d and W 5d. The photocatalytic activities determined by rhodamine B degradation under visible light irradiation (lambda > 420 nm) of Bi2MoxW1-xO6 photocatalysts were significantly improved as compared with Bi2MoO6. The higher efficiency of Bi2WO6 was attributed to more effective photoelectron transfer in the conduction band with larger curvature. The photocatalytic activities under visible light irradiation (lambda > 450 nm) of Bi2MoxW1-xO6 photocatalysts were much higher than that of Bi2WO6. The mechanism was discussed on the basis of the cystal structure, morphology, and electronic stucture. This work provides a strategy for developing active photocatalysts with more utilization of visible light.
Na/Mo co-doped PbTiO3 for photocatalytic water oxidation and Z-scheme overall water splitting under visible light

Haozhi Qi,Yuyang Kang,Jianhang Qiu,Wenyu Zhang,Shangyi Ma,Lianzhou Wang,Gang Liu

DOI: https://doi.org/10.1039/d4cc01761g

IF: 4.9

2024-05-24

Chemical Communications

Abstract:Herein, we demonstrate a sodium/molybdenum (Na/Mo) co-doped ferroelectric PbTiO3 for efficient photocatalysis under visible light. Doped with high concentration of Mo6+, quasi-continuous new energy levels are successfully introduced below the conduction band minimum of PbTiO3, giving rise to a band-to-band redshift of the absorption edge. The valence state difference of Mo6+ and Ti4+ in the doped PbTiO3 is compensated by the Na dopant, thus effectively suppressing the formation of the recombination centres caused by Mo4+. Combined with the intrinsic built-in electric field in PbTiO3, this Na/Mo co-doping strategy enables PbTiO3 superior water oxidation activity under visible light with threshold wavelength up to 550 nm, which also promotes the efficient overall water splitting under visible light in a Z-scheme photocatalytic system. The strategy developed here provides a generally applicable solution to extend the visible light absorption spectrum and engineer electronic structures of ferroelectric materials for photocatalysis and other energy conversion applications.

chemistry, multidisciplinary
Advancing physical, dielectric, and solar photocatalytic efficiency with novel Ni0.95Cu0.03M0.02O (M = Co, Mo) semiconductors

Imen Massoudi,Ahmed Rebey

DOI: https://doi.org/10.1007/s10853-024-10311-5

IF: 4.5

2024-10-12

Journal of Materials Science

Abstract:Cu/Mo codoped NiO semiconductors exhibited a visible light efficient photo-removal performance for diclofenac sodium and methylene blue waste. A simple and low-cost methodology was used to synthesize NiO, Ni 0.95 Cu 0.03 Co 0.02 O, and Ni 0.95 Cu 0.03 Mo 0.02 O nanocatalysts. The crystal structure verified the formation of a cubic NiO single phase. The scanning electron microscopy (SEM) micrographs of all samples have shown a homogenous spherical particle distribution. The harvesting of visible light from NiO semiconductors was significantly enhanced after the addition of Cu/Co and Cu/Mo ions. The X-ray photoelectron spectra confirmed that Cu dopant has a +2-oxidation state while Mo dopant has +3 and +4 as mixed oxidation states. Ni 0.95 Cu 0.03 Co 0.02 O and Ni 0.95 Cu 0.03 Mo 0.02 O have shown high dielectric constant values at low frequencies. For purification of wastewater, the visible light photocatalytic efficiencies of Cu/Mo codoped NiO catalyst for the removal of 20 mg/L methylene blue (MB) and 20 mg/L diclofenac sodium (DS) were 98 and 95% after 50 min, respectively. The MB and DS molecules were converted to CO 2 and H 2 O as confirmed by total organic carbon and chemical oxygen demand analyses. Besides, this nanocatalyst showed a high reusability for MB and DS pollutants until four cycles.

materials science, multidisciplinary
CaMoO4/CaWO4 heterojunction micro/nanocomposites with interface defects for enhanced photocatalytic activity

Huajing Gao,Shifa Wang,Yue Wang,Hua Yang,Fei Wang,Shengnan Tang,Zao Yi,Dengfeng Li

DOI: https://doi.org/10.1016/j.colsurfa.2022.128642

2022-06-01

Abstract:The polyacrylamide gel method combined with low temperature calcination technology (PGMCLCT) have been applied to prepare the CaMoO4/CaWO4 heterojunction micro/nanocomposites with novel light emission and high photocatalytic activity for the degradation of methylene blue (MB) dye. A variety of characterization methods confirmed the formation of heterojunctions between CaMoO4 and CaWO4 in a special interface contact way. The CaMoO4/CaWO4 heterojunction micro/nanocomposites exhibits a novel emission peak at 400 nm with the excitation wavelength of 240 nm and high photocatalytic activity for the degradation of MB dye. With the increase of the mass percentage of CaWO4, the fluorescence emission intensity of CaMoO4/CaWO4 heterojunction micro/nano composites decreases, while the photocatalytic activity increases gradually. The effects of catalyst content, initial dye concentration and cycle index on the photocatalytic activity of CaMoO4/CaWO4 heterojunction micro/nanocomposites were systematically studied. The optimal catalyst content, initial dye concentration, irradiation time and cycle index are 1 g/L, 20 mg/L, 180 min and 5, respectively. The CaMoO4/ wt 20% CaWO4 heterojunction micro/nanocomposites exhibits highest degradation percentage of about 91.44% due to the carbon skeleton or adsorbed oxygen accelerates the separation of photogenerated electrons and hole pairs. This method provides a technical reference for the synthesis of other types of heterojunction micro/nanocomposites.

chemistry, physical
Band Structure and Photocatalytic Properties of Perovskite-Type Compound Ca2NiWO6 for Water Splitting

DF Li,J Zheng,ZG Zou

DOI: https://doi.org/10.1016/j.jpcs.2005.10.182

IF: 4.383

2006-01-01

Journal of Physics and Chemistry of Solids

Abstract:An oxide semiconductor Ca2NiWO6, with double-perovskite crystal structure, was synthesized by solid-state reaction method. The compound Ca2NiWO6 was characterized by X-ray diffraction, UV–visible diffuse reflectance, and photoluminescence. The photocatalytic properties of the compound for water splitting were investigated under UV and visible light irradiation. The results showed H2 evolution was not observed over the compound under visible light irradiation (λ>420nm) with a 300W xenon arc lamp when using methanol (CH3OH) as electron donor, although the compound was responsive to visible light region. Based on the experimental results, a possible band structure was proposed through theoretical calculation of the electronic structure by using the full potential-linearized augmented plane wave (F-LAPW). The band structure and photocatalytic properties were attributed to the special crystal and electronic structures. Due to the oxygen vacancies in the compound, which worked as electron–hole recombination centers, the photocatalytic activity of the compound was low.
One-step synthesis of rod-on-plate like 1D/2D-NiMoO4/BiOI nanocomposite for an efficient visible light driven photocatalyst for pollutant degradation

Thirungnanam Bavani,Vasudevan Vinesh,Bernaurdshaw Neppolian,Sepperumal Murugesan,Manickam Selvaraj,Jagannathan Madhavan

DOI: https://doi.org/10.1007/s11356-022-19982-6

Abstract:Visible light active 1D/2D-NiMoO4/BiOI nanocomposite photocatalyst has been constructed by single step solvothermal method. Various compositions of NiMoO4/BiOI nanocomposites are prepared by loading different amounts of nickel molybdate (NiMoO4) (1, 2, 3 wt%) to the bismuth oxy iodide (BiOI) and investigated by XRD, FTIR, SEM, EDAX, TEM, UV-vis DRS, and PL analysis. Among the as-prepared photocatalysts, 1 wt% NiMoO4 incorporated BiOI (NMBI-1) showed superior photocatalytic activity with a rate constant of 0.0442 min-1 for methylene blue degradation. While the bandgap values of pure BiOI and NiMoO4 are 1.94 and 2.43 eV, respectively, the optimized NMBI-1 exhibited a lower bandgap energy of 1.64 eV, and showed about 2 and 3.7 times higher photodegradation ability than the pure NiMoO4 and BiOI, respectively, towards MB removal under visible light. The NMBI-1 nanocomposite photocatalyst is stable even after four cycles, indicating an excellent photostability and recyclability. Charge carriers on the interface of NiMoO4 and BiOI easily transferred via the newly formed heterojunction, thereby increasing the photocatalytic performance. Photochemically formed h+ and.OH are found to be the major species in the MB removal under visible light illumination. Therefore, the 1D/2D-NiMoO4/BiOI nanocomposite photocatalyst materials may be considered for the wastewater remediation processes.
Porous p-NiO/n-Nb2O5 nanocomposites prepared by an EISA route with enhanced photocatalytic activity in simultaneous Cr(VI) reduction and methyl orange decolorization under visible light irradiation

Fatemeh Hashemzadeh,Ali Gaffarinejad,Rahmatollah Rahimi

DOI: https://doi.org/10.1016/j.jhazmat.2014.12.038

2015-04-09

Abstract:Porous NiO/Nb2O5 nanocomposites with Ni/Nb molar ratio of 0.4, 0.8 and 1.2 have been obtained via the EISA route using P123 copolymer as organic template, and are assigned as NiNb0.4, NiNb0.8 and NiNb1.2, respectively. For comparison, pure Nb2O5 sample assigned as NiNb0.0 was also synthesized by the same method. Structural and textural features of the as prepared samples were investigated by XRD, FTIR, FE-SEM, EDX, UV-vis DRS and BET techniques. The results indicated that the porous p-NiO/n-Nb2O5 junction nanocomposites were formed and coupling of NiO with Nb2O5 resulted a remarkable red shift in the optical response of the nanocomposite samples. The photocatalytic properties of the nanocomposite samples, and also synthesized pure Nb2O5 (NiNb0.0) and commercial Nb2O5 as reference catalysts were evaluated for the first time by simultaneous Cr(VI) reduction and MO decolorization in aqueous suspension under visible light irradiation at pH 2. NiNb0.4 was found to be the most active photocatalyst, which might be attributed to the extended absorption in the visible light region and the effective photogenerated electron-hole separation by the photosynergistic effects of the p-NiO/n-Nb2O5 composite powder. The photocatalytic efficiency of the most active photocatalyst, NiNb0.4, was found to be rather low for either single Cr(VI) solution or single MO solution. However, the photocatalytic reduction of Cr(VI) and photocatalytic decolorization of MO proceed more rapidly for the coexistence system of Cr(VI) and MO than for the single process, showing synergetic effect between the reduction and decolorization reactions. The effects of initial concentration of Cr(VI), MO and the initial pH value on the rate of simultaneous photoreactions over NiNb0.4 sample, were also investigated. The Cr(VI) and MO removal rates were further enhanced by increasing MO and Cr (VI) concentration to an optimal value, respectively, and/or decreasing solution pH.
Ni2O3-modified TiO2 – Xnx As Efficientvisible-Light Photocatalysts

Shuping Zhuo

DOI: https://doi.org/10.3139/146.110272

2010-01-01

International Journal of Materials Research

Abstract:Ni2O3-modified TiO2-xNx visible-light photocatalysts have been prepared by the sol-gel method followed by calcining at 450 degrees C. The photocatalysts were characterized using scanning electron microscopy, thermogravimetry-differential thermal analysis, X-ray diffraction, Fourier transform infrared and X-ray photoelectron spectroscopy. The visible-light photocatalytic activity of the samples was evaluated by decomposition of methylene blue in air under visible-fight irradiation (lambda > 420 nm). Results revealed that the Ni2O3-modified TiO2-xNx samples exhibited irregular particle shapes. The crystal phase of NiO2O3-modified TiO2-xNx samples was anatase. Compared with pure TiO2, the absorption of the Ni2O3-modified TiO2-xNx samples extends significantly into the visible regions due to the doped N atom in the interstitial sites of the TiO2 lattice. The visible-light photocatalytic activity of Ni2O3-modified TiO2-xNx samples was improved greatly since the loaded Ni2O3 can facilitate charge transfer.
Appreciable Enhancement of Photocatalytic Performance for N-doped SrMoO4 via the Vapor-thermal Method

Zhiqiang Yun,Zhenxiang Dai,Liwei Zhu,Ganhong Zheng

DOI: https://doi.org/10.1007/s11595-024-2850-5

2024-01-17

Journal of Wuhan University of Technology-Mater. Sci. Ed.

Abstract:A series of nitrogen-doped SrMoO4 with different Sr/N mole ratio (R=0, 0.05, 0.10, 0.15, 0.20, 0.40, and 0.60) were synthesized using urea as the N source via the vapor-thermal method. The photocatalytic degradation ability of all samples was evaluated using methylene blue (MB) as a target contaminant. The band gaps of N-doped samples are all higher than that of pristine ones, which is only 3.12 eV. BET specific surface area SBET and pore volume are increased due to the N doping. And the greater increase of SBET, the faster the photodegradation speed of methylene blue on SrMoO4. More specifically, the degradation efficiency of MB is improved up to 87% in 100 min.

materials science, multidisciplinary
Facile Formation of Bi2O2CO3/Bi2MoO6 Nanosheets for Visible Light-Driven Photocatalysis

Junlei Zhang,Zhendong Liu,Zhen Ma

DOI: https://doi.org/10.1021/acsomega.8b03699

IF: 4.1

2019-01-01

ACS Omega

Abstract:Bi2O2CO3/Bi2MoO6 heterojunction catalysts were prepared by treating Bi2MoO6 sheets with aqueous NaHCO3 solutions at room temperature. All the Bi2O2CO3/Bi2MoO6 heterojunctions exhibited higher activities than pristine Bi2MoO6 in the photocatalytic degradation of rhodamine B (RhB), methyl orange, and ciprofloxacin under visible-light irradiation, and the most active photocatalyst was found to be the one with a C/Bi molar ratio of ∼1/2.3. Relevant samples were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, N2 adsorption-desorption, Fourier transform infrared spectroscopy, and UV-vis spectroscopy. The higher activity of Bi2O2CO3/Bi2MoO6 than pristine Bi2MoO6 is explained by the enhanced separation and transfer of photogenerated electron/hole pairs, as verified by transient photocurrent densities, photoluminescence spectroscopy, and electrochemical impedance spectroscopy. Photogenerated holes (h+) and superoxide radical anions (•O2 -) were found to be the main active species. The good reusability of Bi2O2CO3/Bi2MoO6 was testified by cycling degradation of RhB and tetracycline hydrochloride.
Ni(OH)2 modified Mn0.5Cd0.5S with efficient photocatalytic H2 evolution activity under visible-light

Yanan Zhang,Jing Wang,Nan Xu,Xuxu Wang,Wenyue Su

DOI: https://doi.org/10.1016/j.ijhydene.2020.06.023

IF: 7.2

2020-08-01

International Journal of Hydrogen Energy

Abstract:Developing high-efficiency photocatalysts for water decomposition is one of the major challenges in converting solar energy to chemical energy. In this paper, Ni(OH)2 modified Mn0.5Cd0.5S solid solution without the use of precious metals is successfully synthesized via hydrothermal method followed by precipitation, the photocatalytic activity for hydrogen evolution and stability of composite samples present significant improvement with respect to the pristine Mn0.5Cd0.5S. These improvements are attributed to that Mn0.5Cd0.5S CB potential (−0.7 V vs. NHE) is more negative than the potential of Ni2+/Ni (−0.23 V vs. NHE), which promotes the transfer of photo-generated electrons from Mn0.5Cd0.5S CB to Ni(OH)2 for H2 production as well as partial reduction of Ni2+ to Ni0, leaving VB holes to oxidize the sacrificial reagents. The metal Ni atoms with conductivity and Ni(OH)2 nanoparticles not only boost the segregation and transfer of photo-induced carriers but also act as water-reduction promoter, thereby promoting the photocatalytic activity for hydrogen release. A novel visible light responsive MnxCd1-xS-based photocatalytic material promising for practical applications is provided in this subject.

energy & fuels,electrochemistry,chemistry, physical

Enhanced photocatalytic oxygen evolution over Mo-doped Ca<sub>2</sub>NiWO<sub>6</sub> perovskite photocatalyst under visible light irradiation

Enhanced photocatalytic oxygen evolution over Mo-doped Ca2NiWO6 perovskite photocatalyst under visible light irradiation

Preparation of WO<sub>x</sub>-TiO<sub>2</sub> and the Photocatalytic Activity under Visible Irradiation

(Mo+n) Codoped TiO2 for Enhanced Visible-Light Photoactivity

Highly Active NiO–CaO Photocatalyst for Degrading Organic Contaminants under Visible-Light Irradiation

A simple mechanical mixing method for preparation of visible-light-sensitive NiO-CaO composite photocatalysts with high photocatalytic activity.

A Novel Series of Photocatalysts M2.5VMoO8 (M = Mg, Zn) for O2 Evolution under Visible Light Irradiation

Carbonate doped Bi2MoO6 hierarchical nanostructure with enhanced transformation of active radicals for efficient photocatalytic removal of NO

Microwave-assisted Synthesis of Mo-doped H1–xSr2Nb3–xMoxO10(x= 0, 0.05, 0.1, 0.15 and 0.2) with High Photocatalytic Activity

Cs-Doped WO3 with Enhanced Conduction Band for Efficient Photocatalytic Oxygen Evolution Reaction Driven by Long-Wavelength Visible Light

Effects of Mo Replacement on the Structure and Visible-Light-Induced Photocatalytic Performances of Bi2wo6 Photocatalyst

Na/Mo co-doped PbTiO3 for photocatalytic water oxidation and Z-scheme overall water splitting under visible light

Advancing physical, dielectric, and solar photocatalytic efficiency with novel Ni0.95Cu0.03M0.02O (M = Co, Mo) semiconductors

CaMoO4/CaWO4 heterojunction micro/nanocomposites with interface defects for enhanced photocatalytic activity

Band Structure and Photocatalytic Properties of Perovskite-Type Compound Ca2NiWO6 for Water Splitting

One-step synthesis of rod-on-plate like 1D/2D-NiMoO4/BiOI nanocomposite for an efficient visible light driven photocatalyst for pollutant degradation

Porous p-NiO/n-Nb2O5 nanocomposites prepared by an EISA route with enhanced photocatalytic activity in simultaneous Cr(VI) reduction and methyl orange decolorization under visible light irradiation

Ni2O3-modified TiO2 – Xnx As Efficientvisible-Light Photocatalysts

Appreciable Enhancement of Photocatalytic Performance for N-doped SrMoO4 via the Vapor-thermal Method

Facile Formation of Bi2O2CO3/Bi2MoO6 Nanosheets for Visible Light-Driven Photocatalysis

Ni(OH)2 modified Mn0.5Cd0.5S with efficient photocatalytic H2 evolution activity under visible-light