Abstract:Measuring human body dimensions is critical for many engineering and product design domains. Nonetheless, acquiring body dimension data for populations using typical anthropometric methods poses challenges due to the time-consuming nature of manual methods. The measurement process for three-dimensional (3D) whole-body scanning can be much faster, but 3D scanning typically requires subjects to change into tight-fitting clothing, which increases time and cost and introduces privacy concerns. To address these and other issues in current anthropometry techniques, a measurement system was developed based on portable, low-cost depth cameras. Point-cloud data from the sensors are fit using a model-based method, Inscribed Fitting, which finds the most likely body shape in the statistical body shape space and providing accurate estimates of body characteristics. To evaluate the system, 144 young adults were measured manually and with two levels of military ensembles using the system. The results showed that the prediction accuracy for the clothed scans remained at a similar level to the accuracy for the minimally clad scans. This approach will enable rapid measurement of clothed populations with reduced time compared to manual and typical scan-based methods.

What problem does this paper attempt to address?

This paper attempts to address the problem of efficiently measuring human body dimensions while wearing clothing. Traditional body measurement methods usually require subjects to change into tight-fitting clothing, which is not only time-consuming and costly but also involves privacy issues. To this end, the research team developed a measurement system based on portable, low-cost depth sensors, using model fitting technology (Inscribed Fitting) to estimate body shape from clothed scan data, thereby providing accurate human feature estimation. Specifically, the system uses three Microsoft Kinect V2 sensors to capture 3D body shapes and fits the scan data through a statistical body shape model, ultimately outputting predicted body dimensions and anatomical landmark positions. ### Main Objectives: 1. **Develop a portable measurement system**: Use low-cost depth sensors (such as Microsoft Kinect V2) to capture the 3D shape of clothed bodies. 2. **Improve measurement efficiency**: Reduce the preparation time and resources required by traditional methods, especially in scenarios requiring large-scale measurements. 3. **Maintain measurement accuracy**: Ensure that the measurement results are similar in accuracy to those obtained under unclothed or tight-fitting clothing conditions. ### Key Technologies: - **Inscribed Fitting (IF) Method**: Find the statistical body shape model closest to the target shape by iteratively adjusting model parameters. - **Point Cloud Data Processing**: Improve the IF method to handle noisy point cloud data obtained from consumer-grade depth cameras. - **Statistical Body Shape Model (SBSM)**: Male and female statistical models built from a large amount of body scan data, used for fitting and predicting body dimensions. ### Experimental Validation: - **Participant Recruitment**: A total of 144 adults (72 females and 72 males) were recruited, representing the distribution of the United States Marine Corps (USMC) population. - **Measurement Methods**: Manual measurements and scans under two different clothing conditions (minimal clothing and military training uniforms). - **Statistical Analysis**: Use Bland-Altman analysis to compare the results of manual measurements and model predictions, evaluating the system's accuracy and consistency. Through these technologies and methods, this study aims to provide a fast, efficient, and accurate solution for large-scale body measurements while wearing clothing.

Efficient Model-Based Anthropometry under Clothing Using Low-Cost Depth Sensors

Data-Driven 3-D Human Body Customization with a Mobile Device

Im2Fit: Fast 3D Model Fitting and Anthropometrics using Single Consumer Depth Camera and Synthetic Data

3D Body Shapes Estimation from Dressed-Human Silhouettes.

Personalized 3D Mannequin Reconstruction Based on 3D Scanning

Measuring Accurate Body Parameters Of Dressed Humans With Large-Scale Motion Using A Kinect Sensor

3D Human Body Reshaping with Anthropometric Modeling

Contactless Body Measurement System Using Single Fixed-Point RGBD Camera Based on Pose Graph Reconstruction

A comparative study of the effectiveness of photogrammetric versus manual anthropometric measurements

High-precision Human Body Acquisition Via Multi-View Binocular Stereopsis

Measuring and modeling human bodies with a novel relocatable mechatronic sensor-net

Automatic Measurement of Scanned Human Body in Fixed Posture

Estimation of 3D Body Shape and Clothing Measurements from Frontal- and Side-view Images

Measurements-to-body: 3D human body reshaping based on anthropometric measurements

Body Weight Estimation Using Virtual Anthropometric Measurements from a Single Image

3D Upper Body Reconstruction with Sparse Soft Sensors

A Fast and Low-Cost Human Body 3D Scanner Using 100 Cameras

3D Body Shapes Estimation from Dressed-Human Silhouettes

Automatic Estimation of Anthropometric Human Body Measurements

Clothes Size Prediction from Dressed-Human Silhouettes.

Dynamic Human Body Reconstruction and Motion Tracking with Low-Cost Depth Cameras