Abstract:Objective To explore the applied value of computer-aided design and three-dimensional printing technology in osteotomy for chin width and prominent mandibular angle.Methods Sixteen patients with chin width and prominent mandibular angle were admitted to the Plastic Surgery Ward of the Second Affiliated Hospital of Zhengzhou University.All patients underwent preoperative computer-aided design,three-dimensional reconstruction of head and face,reconstruction of mandibular nerve canal,intelligent osteotomy line design of chin and mandible,simulation of chin and mandibular angle osteotomy,3-D printing of surgical template to complete osteotomy,and internal fixation of chin osteotomy plate.The mandibular angle (Co-Go-Me),mandibular ramus height (Co-Go),mandibular body length (Go-Me),subfacial width (Go-Go'),chin nodule width (Ge-Ge') and face height (N-Me) were measured preoperation,before surgical simulation and postoperation.Co-Go-Me,Co-Go/Go-Me,Go-Go'/N-Me and Ge-Ge'/N-Me were compared and analyzed in preoperation,before surgical simulation and postoperation.Results All the patients were satisfied with their facial shape.The mandible was almost symmetrical after operation.No complications such as nerve injury and infection occurred after operation,which fully met the preoperative design requirements.The mandibular angles in the left and right sides of patients before operation were significantly less than those after operation (t =2.890,2.886,P ＜ 0.05).There was no significant difference in the mandibular angles in the left and right sides of pa tients before and after operation (t =0.200,0.201,P ＞ 0.05).The average mandibular angles after operation were (123.9 ± 3.0)°.Co-Go/Go-Me in the left and right sides of patients before operation was significantly higher than that after operation (t =3.607,2.860,P ＜ 0.05).There was no significant difference in the simulated Co-Go/Go-Me in the left and right sides before and after operation (t =0.067,0.069,P ＞ 0.05).The ratio of the length of the left and right mandibular body to the height of the ascending ramus was close to 2:1.Preoperative Go-Go'/N-Me was significantly higher than that post-operation (t =3.102,P ＜0.05).Preoperative simulated Go-Go'/N-Me was not significantly different from postoperative Go-Go'/N-Me (t =2.011,P ＞0.05).Preoperative Ge-Ge'/N-Me was significantly higher than that post-operation (t =3.010,P ＜ 0.05).Preoperative simulated Ge-Ge'/N-Me was not significantly different from post-operative Ge-Ge'/N-Me (t =2.010,P ＞ 0.05).Conclusion The application of computer-aided design and three-dimensional printing technology in osteotomy for large chin and hypertrophic mandibular angle can significantly improve the accuracy of operation,reduce the difficulty of operation,improve the cosmetic effect,and reduce the occurrence of complications such as infection and injury of important nerves and blood vessels.

Application of HaiMed refractory wound artificial intelligence assisted system in wound measurement

Cephalometric measurements of mandibular shape after mandibular angle osteotomy

Application of Three-Dimensional Printing Technology in Osteotomy for Chin Width and Prominent Mandibular Angle

A Modified Intraoral and Extraoral Approach Osteotomy for the Prominent Mandibular Angle.

A Prospective Investigation of Patient Satisfaction and Psychosocial Status Following Facial Bone Contouring Surgery using the Face-Q

Aesthetic Enhancement of the Gonial Angle and Inferior Mandibular Border in the Chinese Population

Quality-of-life Evaluation after Microvascular Oromandibular Reconstruction: A Comparative Study of Reconstucted and Nonreconstructed Patients

Automated Preoperative Planning Algorithm for Mandibular Angle Osteotomy Based on Anatomical Landmarks Detection: A Retrospective Study

Clinical effect of endoscopic-assisted intraoral reduction mandibuloplasty

Appraising mandibular prognathism in class III malocclusion following orthognathic surgery: Patient-reported and cephalometry-based outcomes

Computer-assisted mandibular curved osteotomy: An automatic method to design the new aesthetic gonion and osteotomy line

Intraoral Multistage Mandibular Angle Ostectomy

Short-term and long-term psychological impact and quality of life of patients undergoing orthognathic surgery

"Stamp Perforation" Technique for Correction of Prominent Mandibular Angle: 10 Years of Experience in Mandibular Reshaping in Asians

Relations between bone density from computed tomography and bone regeneration after reduction mandibuloplasty

Intraoral Approach for the Correction of Prominent Mandibular Angle with Masseter Muscle Hypertrophy

[Improvement of the mastication function of orthodontics combined with restoration in the treatment of deep overbite with severe lower anterior teeth attrition]

The aesthetic proportion index of facial contour surgery

Patient-Perceived Improvement in Facial Appearance and Quality of life: FACE-Q as a Tool to Study Reduction Mandibuloplasty Outcomes

Impact of the orofacial muscular rehabilitation exercise on facial expression recovery post-orthognathic surgery

Health‐related quality of life, jaw function and sleep‐disordered breathing among patients with dentofacial deformity