Abstract:Turbomachinery design typically foresees three different phases: conceptual, preliminary and detailed. Conceptual design is the first stage of industrial design process, providing mainly the architectures down-selection. Traditionally, this phase is driven by the target "performance" as the main goal to be achieved. Therefore, the design team sketches an early configuration looking at this goal. Performances can be affected by material and geometry changes, manufacturing technology and engine architecture. Conceptual design phase is dramatically important, as the outcome of the down selection will not only affect performances, but also other important parameters like "cost" and "environmental impact". Moreover, in conceptual phase the configuration is still under definition and the designer has the highest flexibility in defining and then designing the product. Cost and environmental sustainability are comparable to performance as drivers in industrial design process from the earliest stage. Connections between performance, cost and carbon footprint (CF) are fundamental in decision making and down-selection process. Usually, cost estimations are tailored to each design and technical requirements, to give an assessment of the costs from the buyer's point of view. Assessment of the environmental impacts can be carried out by means of the Life Cycle Assessment (LCA) methodology (ISO 14040: 2006, ISO 14044:2006), looking at the whole life cycle of the product. Therefore, as boundary definition can be different, there is a possibility that cost estimation and LCA results are not consistent with each other due to different system boundaries, leading to misinformed decisions. To overcome this issue, the principles underlying the environmental Life Cycle Costing (e-LCC) method can be used (Hunkeler et al. 2008). It integrates both LCA and LCC studies, based on the same functional unit and system boundaries. This article will present a case study of a supercritical CO2 turboexpander inner casings' subsystem conceptual design and architecture down selection to propose an approach for maximizing product's sustainability and performance. Results show the relevance of the geographical location of suppliers on the CF, as well as how small changes on the overstock materials could lead to a relevant change in costs.

Defining Key Environmental Performance Factors (KEPF) for Gas Turbines Eco-Design and Production Through Life Cycle Assessment

Implementing Environmental Impact Assessment On The Life Cycle For Industrial Gas Turbines Development

Design for Sustainability of Gas Turbines: Accuracy on Carbon Footprint at Different Design Steps

Decarbonizing Materials Sourcing and Machining in the Gas Turbine Sector, Through a Cost-Carbon Footprint Nexus Analysis

Application of Design-for-LCA Methodology to Compare Architectural Alternatives for the Compressor Rotor of an Industrial Gas Turbine

Decarbonizing Materials and Machining for the Gas Turbines Sector Through Life Cycle Assessment

Exergoenvironmental Evaluation for Combined Cycle Power Generation System Based on Life Cycle Assessment

A Carbon Footprint Comparison Through LCA of Forging Vs. Wire Arc Additive Manufacturing (WAAM) Processes for the Internal Casing of a Gas Turbine

Residual Life Prediction Method for Gas Turbine HGP Component Based on Multi-environmental Time Similarity Theory

A Knowledge-enriched Framework for Life Cycle Assessment in Manufacturing

Multi-objective conceptual design of turboexpander subsystems: inner casings, a case study

Effects on Sustainability by Redesign of a 1° Stage Gas Turbine Nozzle Ring from Investment Casting to Additive Manufacturing: A Life Cycle Environmental Impact Comparison

Additive Manufacturing Versus Investment Casting for a Gas Turbine Component: a Social Life Cycle Comparison

Coupling life cycle assessment and life cycle costing as an evaluation tool for developing product service system of high energy-consuming equipment

Eco-performance evaluation of product designs – an integrated fuzzy complex proportional assessment with life cycle assessment

Design, Testing, and Performance Impact of Exhaust Diffusers in Aero-Derivative Gas Turbines for Mechanical Drive Applications

Comparative Life Cycle Assessment of a centrifugal compressor impeller: Hybrid technology production versus welding production

Comparing Environmental Impacts of Additive Manufacturing Vs. Investment Casting for the Production of a Shroud for Gas Turbine

Multidiscipinary Optimization For Gas Turbines Design

Knowledge Graph-Based Mapping and Recommendation to Automate Life Cycle Assessment

Study of the effect of fuel temperature on gas turbine performance