Abstract:The frost of the evaporator can greatly affect the performance of the air source heat pump. When humid air comes in contact with a cold surface maintained below the freezing temperature, a frost layer begins to grow. This paper experimentally studied the frosting process of a folded-louvered-fin, parallel flow evaporator in a heat pump central air-conditioning system under three conditions, in which three different diameter capillaries were used. The surface temperature distribution of the evaporator was measured by sixteen thermocouples which buried on the leeward side and mesoscale frost formation processes on its partial surface for three different test conditions were observed using a CCD camera. The experimental result showed that the surface temperature distribution of the parallel flow evaporator was non-uniform and frost formation generally began on some partial surface of the louvered fins where the surface temperature was lowest after the heat pump system had starting up for six minutes under condition B and C, while the fins began to frost after eight minutes under condition A. The non-uniform surface temperature distribution which was caused by the unequal distribution of the refrigerant flux in the microchannels of flat tubes led to uneven distribution of frost, furthermore, incomplete evaporation of refrigerant in some tubes may be a critical factor of folded-louvered-fins’ easily frost under relative high environmental temperature condition. The ice crystals distributions and frost thickness in frost period can be obtained by the digital image processing method in which the initial pictures can be converted into binary image. The results showed that in a thin layer near to fins’ surface, ice crystals were comparable high dense in the frost growing and full grown period of frost layer; the ice crystals rate was reduced in approximate linear curves with the increasing of the frost thickness (frost height), where the decreasing rate in the frost full grown period was slower than that in the frost growing period (In 0.1 mm frost thickness, the ice crystals rate had decreased to 58% in the frost growing period, while in the frost full grown period the ice crystals rate was 90%; and in 0.25 mm frost thickness, the ice crystals rate were 0%, 45% respectively.). It also can be found that the frost thickness increased as the time increasing and then finally reached 0.3mm, 0.35 mm, and 0.32mm respectively at three conditions. The frost thickness had reached 0.1mm, 0.05mm under condition B and C respectively in 6 minutes, however, concerning condition A, the frost began to grow after 8 minutes and frost thickness arrived only 0.05mm in 14 minutes.

Heat Transfer Analysis of Evaporator of Air Source Heat Pump (ASHP) in Case of Frost Based on Chirplet Finite Element Method

Comparative research on the heat transfer efficiency of evaporators with different structures used in a large quick-freeze plant

Thermal Design of Large Plate-Fin Heat Exchanger for Cryogenic Air Separation Unit Based on Multiple Dynamic Equilibriums

Dynamic simulation of an air-source heat pump water heater using novel modified evaporator model

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Simulation Analysis on Dynamic Performance of a Combined Solar/air Dual Source Heat Pump Water Heater

Analysis on Performance of a Novel Frost-Free Air-Source Heat Pump System

Dynamic characteristics of refrigerant evaporation temperature in air-water heat source heat pump

Frost/Defrost Models for Air-Source Heat Pumps with Retained Water Refreezing Considered

Frosting for Airside Heat Exchanger of the Water Chiller/heater of Air Source Heat Pump

A prediction model of air-source heat pump system performance with frost-retarded heater

Simulation Study on Performance of an Air Source Heat Pump System Combined with Phase Change Thermal Storage Using Alternative Refrigerants

Investigation of the Frost Growth on a Parallel Flow Evaporator

Performance Investigation on an Air Source Heat Pump System with Latent Heat Thermal Energy Storage

Frosting Phenomenon and Frost-Free Technology of Outdoor Air Heat Exchanger for an Air-Source Heat Pump System in China: An Analysis and Review

Visualization experiment and numerical simulation on behaviors of gas-liquid falling film flow on the air-side of two-row plain finned-tube heat exchanger

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Analysis on frosting of heat exchanger and numerical simulation of heat transfer characteristics using BP neural network learning algorithm

A Modelling Study on the Frosting Characteristics of a Novel Dual-Fan Outdoor Coil in an Air Source Heat Pump Unit

A newly designed air-source heat pump system with liquid subcooling defrosting: Simulation and experiment

Study on Frost-Suppression Characteristics of Superhydrophobic Aluminum Surface Heat Exchanger Applied in Air Source Heat Pump