Abstract:The sericite mica was first treated by heating and acid dipping followed by LiNO3 treatment. The organophilic clay was subsequently achieved by inorganic-organic ion exchange in the hydrothermal reaction of LiNO3-treated sericite mica with intercalating agent-hexadecyltrimethylammonium bromide solution. Finally, a series of polyimide (PI)/sericite mica composites were prepared via in situ polymerization reaction. The effects of the reaction temperature and the amount of intercalating agent added on the modification of sericite mica were investigated. The structures of modified and original sericite mica were systemically characterized with Xray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM), showing the best intercalating effect was observed when the reaction temperature was 180 C and the amount of intercalating agent added was fifteenfold the cation exchange capacity (CEC). Under the above reaction conditions, the do basal spacing of the sericite mica was increased from 0.99 nm to 2.77 nm. The structure of the composites was investigated by XRD and high resolution transmission electron microscopy (HRTEM), and the thermal stability and the mechanical properties were studied by means of thermogravimetric analysis (TGA) and mechanical property measurements, indicating that the PI/original sericite mica composite was a simple physical blend of PI and pure sericite mica, while the PI/organic sericite mica nanocomposites was an exfoliated structure with 5 wt% loading and the nanocomposites with the content of 1 wt% 7 wt% organophilic sericite mica exhibited no observable peaks in the range of 0.5 degrees similar to 10 degrees (2 theta), which revealed that majority of the d(002)-spacing of organophilic sericite mica had been intercalated to a distance of more than 4.42 nm (2 theta < 1 degrees). When the mass ratio of sericite mica and PI was 5: 100, the tensile strength, Young's modulus and elongation at break of the PI/organic sericite mica nanocomposites are 1.79, 1.40 and 1.83 times those of the PI/original sericite mica counterpart, respectively. The thermogravimetric analysis showed that the thermal stability was tremendously enhanced with the increasing organophilic sericite mica content and the nanocomposites with 7 wt% loading revealed a 36 K increment in T-5 (the temperature at 5 wt% weight loss) compared with pristine PI.

Preparation and Characterization of Quaternary Ammonium Salt and 3-Aminopropyltriethoxysilane Modified Sericite Mica

Preparation and Characterization of Cetyl Trimethylammonium Intercalated Sericite

Preparation and Characterization of Polyimide/Sericite Mica Composites

Preparation and Characterization of Activated Sericite Modified by Fluorosilicate

Microstructural Modification and Characterization of Sericite

The Modification and Characterization of Thermal-Treated Sericite by Fluorosilicate

Preparation and Characterization of Activated Sericite Modified by Fluorosilicate and Acid

Surface Modification of Halloysite/Sericite

Intercalation of Cetyl Trimethylammonium Ion into Sericite in the Solvent of Dimethyl Sulfoxide

Preparation, Microstructure, Mechanical, and Thermal Properties of in Situ Polymerized Polyimide/Organically Modified Sericite Mica Composites

The Stability of Intercalated Sericite by Cetyl Trimethylammonium Ion under Different Conditions and the Preparation of Sericite/Polymer Nanocomposites

Preparation and Characterization of Quaternary Ammonium Complex Silane Coupling Agent Modified Montmorillonite

Hexadecyltrimethylammonium Bromide-Modified Sericite Mica-Based Polyimide Composites: A Comparison Between in Situ Polymerization and Solution Intercalation Processes

A Comparative Investigation on Different Silane Coupling Agents Modified Sericite Mica/polyimide Composites Prepared by in Situ Polymerization

Mineralized Substance Deposited on Sericin Film Surface After Treatment with Alternate Dipping Mineralization Cycles and Change of Siericin Film Structure

Separation And Study Of Cetyltrimethylammonium Ion Intercalated Trioctahedral Smectite With Reduced Layer Charge

Structure and Properties of Polyimide/sericite Composite Adhesive Prepared Bypolyamide Acid Salt Method

MESOPOROUS MOLECULAR SIEVES MCM–41 PREPARED FROM POST-Mg– EXTRACTION SEPIOLITE

Emulsion-templated High Porosity Mullite Ceramics with Sericite Induced Textured Structures

Efficient inhibition of montmorillonite swelling through controlling flexibly structure of piperazine-based polyether Gemini quaternary ammonium salts

Surface modification of sericite by silane coupling agent and application in natural rubber