Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Abnormal Spatial Heterogeneity Governing the Charge-Carrier Mechanism in Efficient Ruddlesden–Popper Perovskite Solar Cells

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Charge‐Carrier Transport in Quasi‐2D Ruddlesden–Popper Perovskite Solar Cells

Ruddlesden–Popper Perovskites: Energetics and Energy Loss in 2D Ruddlesden–Popper Perovskite Solar Cells (adv. Energy Mater. 23/2020)

Self-formed 2D/3D Heterostructure on the Edge of 2D Ruddlesden-Popper Hybrid Perovskites Responsible for Intriguing Optoelectronic Properties and Higher Cell Efficiency

Efficient vertical charge transport in polycrystalline halide perovskites revealed by four-dimensional tracking of charge carriers

Energetics and Energy Loss in 2D Ruddlesden–Popper Perovskite Solar Cells

Inter-phase Charge and Energy Transfer in Ruddlesden–Popper 2D Perovskites: Critical Role of the Spacing Cations

Nanoscale chemical heterogeneity dominates the optoelectronic response of alloyed perovskite solar cells

Self‐Assembled Molecules Fostering Ordered Spatial Heterogeneity for Efficient Ruddlesden‐Popper Perovskite Solar Cells

Spontaneous Formation of 2D/3D Heterostructures on the Edges of 2D Ruddlesden–Popper Hybrid Perovskite Crystals

Coordination Engineering of Single‐Crystal Precursor for Phase Control in Ruddlesden–Popper Perovskite Solar Cells

Interlayer Interaction Enhancement in Ruddlesden–Popper Perovskite Solar Cells Toward High Efficiency and Phase Stability

Uniform Phase Permutation of Efficient Ruddlesden–Popper Perovskite Solar Cells via Binary Spacers and Single Crystal Coordination

Homogenization of Halide Distribution and Carrier Dynamics in Alloyed Organic-Inorganic Perovskites

Improve the Charge Carrier Transporting in Two-Dimensional Ruddlesden-Popper Perovskite Solar Cells

Origination of Anomalous Current Fluctuation in Perovskite Solar Cells

Aligned and Graded Type‐II Ruddlesden–Popper Perovskite Films for Efficient Solar Cells

Interplays between charge and electric field in perovskite solar cells: charge transport, recombination and hysteresis

Layer Distortion Engineering for Spontaneous Charge Separation in Two-Dimensional Perovskites

Electronic Disorder Dominates the Charge-Carrier Dynamics in Two-Dimensional/Three-Dimensional Organic–Inorganic Perovskite Heterostructure