Method for Measuring Full- Field Deformation Based on Double-Sided Mirror and Dual-Camera Combination
Li Guihua,Li Tao,Sun Weiqing,Gong Qicheng,Wang Xiaoyu,Zhang Mei
DOI: https://doi.org/10.3788/AOS221324
2023-01-01
Acta Optica Sinica
Abstract:Objective The application of digital image correlation ( DIC) technology is very extensive, and the technology has high practical value in biotechnology, civil engineering, aerospace, medical application, and other fields. With the continuous advancement of related technologies, the demand for full-field deformation measurement and 3D shape reconstruction of objects has increased accordingly. This requires the DIC technology to not only have higher measurement accuracy but also be more economical and practical, so as to make itself be applied to more fields. In recent years, many scholars have done a lot of research on the full field strain and deformation measurement by DIC, and they have made many valuable research results. Among them, the multi-camera DIC system has been proven to have high measurement accuracy, and it is feasible to achieve full field or double surface deformation measurement. However, in actual use, the system takes a long time to be built and involves a complex operation and high economic costs, and there is interference between multiple cameras. The rotation of a single camera is used to realize the full field deformation measurement of the measured object under different load conditions. In other words, the camera is continuously moved to rotate around the same measured object, and it will shoot and record in multiple different positions, so as to finally cover all the required fields of view. The system has low cost, complex operation, and low accuracy. In view of the problem that a monocular camera is difficult to be used in full- field deformation measurement and the complexity of multiple cameras in full- field deformation measurement, a new method of full-field deformation measurement by using a double-sided mirror-assisted dual-camera system is proposed. Methods This research adopts a coordinate transformation method based on camera calibration. In other words, the transformation from the real camera coordinate system to the virtual camera coordinate system is realized through the double-sided mirror, and then the transformation from the real object to the virtual image is realized. It is assumed that the camera coordinate system of L coincides with the world coordinate system of the binocular DIC system (Fig. 3). Therefore, the conversion relationship between the world coordinate system of the virtual binocular DIC system and that of the real binocular DIC system is equivalent to the conversion relationship between the camera coordinate systems of L' and L. First, it is necessary to find out the positional relationship between the coordinate system o c-x cy c z c and the O 1 -X(1)Y(1)Z(1). The rotation and translation matrices between the camera coordinate system o c-x cy cz c and O-1 - X(1)Y(1)Z(1) can be obtained through camera calibration. Then, an intermediate coordinate system is introduced, namely, the coordinate system O 2X(2)Y(2) Z(2), which is a rotating coordinate system of O-1 - X(1)Y(1)Z(1). According to the imaging law of the plane mirror and the nature of the Euler angle, the rotation and translation matrices from the coordinate system o v-x v y v z v to the coordinate system O-2-X2Y2 Z(2) can be obtained, and then the rotation and translation matrices from the coordinate system o v - x vy vz v to the coordinate system O-1 -X-1 Y(1)Z(1) can be obtained. Finally, the conversion relationship between the real camera coordinate system and the virtual camera coordinate system can be calculated by synthesizing the above results. Results and Discussions With a hollow hexagonal aluminum bar as the research object, the proposed method is used to conduct 3D reconstruction and thermal deformation research (Fig. 4). In the 3D reconstruction experiment, the maximum reconstruction deviation between the reconstructed surface and the fitted surface is about 0. 004 mm, and it is mainly concentrated in the splicing area, while the deviation in other areas is relatively stable. The stereo reconstruction angle also proves that the system has stable performance and high accuracy ( Fig. 6). In the thermal deformation research experiment, the proposed method can be used to obtain the average height of the first and last frame images in the vertical direction of the B and C surfaces of the part, respectively (Table 1). It can be seen that the maximum change in the height of surface B of the part is 0. 5467 mm, and that of surface C is 0. 5589 mm ( Fig. 7). Then, the height change of surface A of the part processed by the system are directly compared with that of surfaces B and C processed by the proposed method during the cooling process, and comparison is carried out every 30 frames from frame 0 to 1290. There are 44 frames of comparison images ( Fig. 8). Finally, the finite element analysis software ANSYS is used to simulate the part, and the steady-state simulation is selected. The temperature of the part rises from 20 degrees C to 310 degrees C in simulation experiments. It can be seen that the maximum thermal deformation of the part in the vertical direction is 0. 5500 mm, which indicates that the thermal deformation of the part along the z direction is 550. 0 mu M when the temperature difference is 290 degrees C [Fig. 9 (b)]. Conclusions A new method of full field deformation measurement using a double- sided mirror-assisted binocular DIC system is proposed. With a hollow hexagonal aluminum bar as the measuring object, the thermal deformation results of three outer surfaces are measured during the cooling process from 310 degrees C to 20 degrees C, and they are compared with the simulation results of the finite element software. The results show that the change curves of the three outer surfaces of the part along the height direction basically coincide with the simulation results, and the absolute error between the calculated average thermal deformation values of A, B, and C surfaces along the height direction of the part by using the proposed method and the simulation results is 2. 8 mu m. The relative error is only 0. 51%. It can be seen that the proposed method not only overcomes the limitation that a monocular camera cannot realize full field measurement but also discards the complexity of a multi- camera DIC system.