Abstract:Advances in Mechanical Engineering, Volume 14, Issue 8, August 2022. Five series of specimens with two different print orientations (−45/45 and 0/90) and two print layer thicknesses (0.1 and 0.2 mm) were made. In total 60 specimens with 100% filament infill were made. One specimen series (20 pieces) was isolated as a reference or thermally untreated. Before the thermal treatment (annealing), two specimen moulding methods were used: NaCl powder (granulation 63 mm: 20 pieces) and Calcium Sulphate (Gypsum: 20 pieces). During the annealing, specimens immersed in NaCl powder were heated in a drying oven to the filament melting point (for PLA: 200°C, with a duration interval of 30 min), while the treatment of the heated specimens in gypsum was performed at a temperature of around 190°C, with duration interval of 3 h with the observed temperature inside the mould of about 100°C. An ultrasonic bath and a drying oven were used in the gypsum treatment. Temperature measurement and control during both annealing treatments were performed using a thermal imaging camera, while the temperature control inside the drying oven was performed using a digital thermometer. After treatment, the specimens in the moulds were cooled at room temperature, and the dimensions of annealing and untreated specimens were controlled. Surface morphology was characterised using scanning electron microscopy (SEM). The SEM analysis reveals improved internal structure after heat treatment of the PLA specimens. These results show that the investigated specimens after heat treatments had better structural properties than the referent specimens. Tensile testing on a universal testing machine in compliance with the ASTM D638 standard was also performed. The referent PLA specimen with −45/45 and layer thickness of 0.1 mm had the highest tensile stress value (64.08 MPa) while the specimen with minimal tensile stress value before fracture was 0/90, 0.2 mm (54.81 MPa). Heat treatment in gypsum showed the most significant increase in strength with −45/45 (0.1 mm) being the strongest (71.66 MPa) while the strongest specimen treated in sodium chloride was −45/45 (0.1 mm) with maximum tensile stress of 70.08 MPa. The mechanical characteristics of the PLA were characterised using the Vickers microhardness tester. The PLA microhardness value was calculated according to standards ASTM E384 and ISO 6507. The referent PLA specimen with −45/45 (0.2 mm) orientation shows the maximal microhardness value (125 MPa), and the minimal microhardness value was observed for the 0/90 (0.1 mm) orientation specimens (108 MPa). The heat treatment specimens in gypsum have a better hardness (185 MPa) than those treated in gypsum (165 MPa), with microhardness increasing by about 12%. The essence of the work is reflected in the additional filament processing to achieve a better structural and mechanical performance of the materials and reduce the anisotropy that is characteristic of 3D printing.

Tailoring the Thermal and Mechanical Properties of Injection‐molded Poly (lactic Acid) Parts Through Annealing

Effect of Crystallization Temperature on Crystal Modifications and Crystallization Kinetics of Poly(l‐lactide)

Polymorphic Transition in Disordered Poly(l-lactide) Crystals Induced by Annealing at Elevated Temperatures

Manipulation of Non-Isothermal Crystallization Kinetics of Poly(lactic Acid) Composite Film by a Novel Nucleating Agent

Effect of poly(lactic acid) crystallization on its mechanical and heat resistance performances

Development of High Temperature Resistant Stereocomplex PLA for Injection Moulding

Annealing-induced oriented crystallization and its influence on the mechanical responses in the melt-spun monofilament of poly(L-lactide)

Thermal annealing of injection molded VHMW PLLA

Effect of thermal annealing on crystal structure and properties of PLLA/PCL blend

Preparation and properties of the crosslinked poly( L -lactide) with high crystallinity and high gel content

Vibration-assisted injection molding: an efficient process for enhanced crystallinity development and mechanical characteristics for poly lactic acid

Enhancing mechanical properties of 3D printed thermoplastic polymers by annealing in moulds

Growth of molecular orientation during post‐process annealing of poly(lactic acid) containing a fibrous nucleating agent

Regulating mechanical performance of poly (l-lactide acid) stent by the combined effects of heat and aqueous media

Crystallization Morphology Regulation on Enhancing Heat Resistance of Polylactic Acid

Probing Into the Annealing Effects on Microstructure and Mechanical Properties of Impact Polypropylene Copolymer With Nodular Crystalline Morphology

Effect of Plasticization/Annealing on Thermal, Dynamic Mechanical, and Rheological Properties of Poly(Lactic Acid)

Thermal And Crystallinity Property Studies Of Poly (L-Lactic Acid) Blended With Oligomers Of 3-Hydroxybutyrate Or Dendrimers Of Hvdroxyalkanoic Acids

Effects of heat treatment on the mechanical properties of 3D-printed polylactic acid: Study of competition between crystallization and interlayer bonding

Influence of Processing Parameters on Mechanical Properties and Degree of Crystallization of Polylactide

Manipulating Crystallization for Simultaneous Improvement of Impact Strength and Heat Resistance of Plasticized Poly(l-lactic acid) and Poly(butylene succinate) Blends