Abstract:Context: Powder metallurgy uses metallic and/or non-metallic powders that, through mixing, compacting, and sintering operations, allow obtaining large series of products. In austenitic stainless steels, Cr23C6-type carbides can precipitate at temperatures between 450 and 950 °C. When this occurs, the steel is susceptible to being attacked at its grain boundaries by a phenomenon called sensitization. Titanium is added as a ‘stabilizer’ because it has a greater affinity with carbon for the formation of species at a temperature of approximately 900 oC, and, during cooling, it consumes the carbon forming MC-type carbides, inhibiting the precipitation of Cr23C6. Method: The composition and morphology of the powders were characterized, leading to the formulation of an alloy matrix consisting of a mixture of AISI 316 steel powders of two different particle-size distributions in a proportion that produced the highest density and the lowest porosity in the sintered material. Titanium was added at two levels (0,4 and 1,0 wt%), and sintering was carried out with nitrogen. The corrosion rate was determined by potentiodynamic polarization. Vickers hardness and pin-on-disk wear tests were performed. The stages were complemented with a microstructural analysis. Results: The addition of 0,4 wt% of titanium decreased the steel’s rate of corrosion, albeit in the absence of passivation. The microstructure consists of austenite, ferrite, and TiC precipitates. The addition of 1,0 wt%Ti showed an increase in the corrosion rate, with a microstructure containing austenite, ferrite, TiC carbides, and the Laves ɳ-Fe2Ti phase. Conclusions: The results were compared against thermodynamic simulations in the Thermo-Calc software, which were consistent with the microstructural analysis, showing the phenomena of stabilization as well as the precipitation of intermetallic phases and highlighting the importance of establishing strict controls in the formulation of powder metallurgical alloys due to the transformations that can take place due to the effect of the thermal cycles of the process.

Influence of Addition of TiAl Particles on Microstructural and Mechanical Property Development in a Selectively Laser Melted Stainless Steel

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Simultaneously Improved the Strength and Ductility of Cast Al-3Li-2Cu Alloy by Ti Addition and Heat Treatment

Strengthening Mechanisms in Selective Laser Melted 316L Stainless Steel

Effect of In-Situ TiB2 Particles on Microstructure and Mechanical Properties of Al–Fe–Ni Manufactured by Selective Laser Melting

Effect of the Addition of Cu and Al on the Microstructure, Phase Composition and Properties of a Ti-6Al-4V Alloy Obtained by Selective Laser Melting

Enhancing strength and ductility of AlSi10Mg fabricated by selective laser melting by TiB2 nanoparticles

Influence of Tungsten Addition on Microstructure and Tensile Properties of Ti6Al4V Fabricated by Laser-Directed Energy Deposition

Inoculation treatment of an additively manufactured 2024 aluminium alloy with titanium nanoparticles

Effect of Titanium Addition on As-Cast Structure and High-Temperature Tensile Property of 20Cr-8Ni Stainless Steel for Heavy Castings

Improvement of mechanical properties through inhibition of oxidation by adding TiC particles in laser aided additive manufacturing of stainless steel 316L

Constructing a Novel Bi-Lamellar Microstructure in Selective Laser Melted Ti-6Al-4V Alloy Via Electropulsing for Improvement of Strength and Corrosion Resistance

Study Of the Effect of Titanium Additions on The Mechanical and Corrosion Properties of AISI 316 Powder Metallurgical Steel

Enhanced mechanical performance of duplex stainless steels via dense core-shell nano-inclusions in-situ formed upon selective laser melting

A comprehensive study on microstructure and tensile behaviour of a selectively laser melted stainless steel

The Evolution of Oxygen-Rich Nanoparticle and Its Effect on the Mechanical Property in Selective Laser Melted 304L Stainless Steel

Enhanced strength–ductility synergy and transformation-induced plasticity of the selective laser melting fabricated 304L stainless steel

Influence of Al-Ti-B Addition on the Microstructure and Mechanical Properties of A356 Alloys

The Effect of Al and Ti on the Microstructure, Mechanical Properties and Oxidation Resistance of Γ′-Ni3(al, Ti) Strengthened Austenitic Stainless Steels

Additive manufacturing of a nanocrystalline lathy Ti6Al4V5Cu alloy with high strength and ductility combination