Abstract:Herein, a family of thiourea containing silicone-based photoresins suitable for creating silicone objects with excellent elasticity was developed for use in conventional digital light processing 3D printers. Rapid manufacturing of silicone products is highly desirable for small-volume manufacturing, especially for the application of customer-specific medical devices. However, because of their intrinsic high viscosity and lack of intermolecular interactions, 3D printing with silicone remains an ongoing challenge as suitable resins are not commercially available. To improve the elasticity of 3D-printed silicones, dynamic noncovalent intermolecular interactions between polymer chains were increased through the introduction of thiourea groups. Furthermore, a molecular design strategy was implemented based on utilizing "oligomeric" and "polymeric" PDMS units to adjust the ratio of thiourea segments. The cured silicone elastomer developed here displayed a maximum elongation of up to 1000% under tensile load and excellent cyclic compression durability. Moreover, this approach allowed for the 3D printing of PDMS-based objects with complex microarchitectures, high resolution, excellent surface finishing, and low cytotoxicity. The silicone thiourea resins have potential application in medical devices, wearable devices, and soft robotics.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsapm.1c00260?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsapm.1c00260</a>.Polymerization data of PDMS–thiourea polymers, <sup>1</sup>H NMR spectra of a typical PDMS–thiourea polymer, mechanical properties of cured silicones, representative photographs of printed parts, and cell morphological data for MTS assay (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_001.pdf">PDF</a>)Movie S1 showing the cyclic tensile of our cured silicone (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_002.avi">AVI</a>)Movies S2 and S3 showing the stretchability of the printed part (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_003.avi">AVI</a>) (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_004.avi">AVI</a>)This article has not yet been cited by other publications.

Binder Jetting of Custom Silicone Powder for Direct Three-Dimensional Printing of Maxillofacial Prostheses

Rapid Printing of 3D Porous Scaffolds for Breast Reconstruction

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Fabrication of Low Cost Soft Tissue Prostheses with the Desktop 3D Printer

3D Direct Printing of Silicone Meniscus Implant Using a Novel Heat-Cured Extrusion-Based Printer

Embedded 3D printing and pressurized thermo-curing of PMMA for medical implants

Biofunctional Glycol-Modified Polyethylene Terephthalate and Thermoplastic Polyurethane Implants by Extrusion-Based Additive Manufacturing for Medical 3D Maxillofacial Defect Reconstruction

Cost-Effective 3D Printing of Silicone Structures Using an Advanced Intra-Layer Curing Approach

3D Printing of High Viscosity Reinforced Silicone Elastomers

Digital Light Processing 3D Printing of PDMS-Based Soft and Elastic Materials with Tunable Mechanical Properties

A Heating-Assisted Direct Ink Writing Method for Preparation of PDMS Cellular Structure with High Manufacturing Fidelity

Silicone 3D Printing: Process Optimization, Product Biocompatibility, and Reliability of Silicone Meniscus Implants

3D Printing by Multiphase Silicone/Water Capillary Inks

3D printing of silk powder by Binder Jetting technique

Embedded 3D Printing of PDMS-Based Microfluidic Chips for Biomedical Applications

A TMPS-designed personalized mandibular scaffolds with optimized SLA parameters and mechanical properties

3D Printing of PDMS Improves Its Mechanical and Cell Adhesion Properties

Direct Three-Dimensional Printing of a Highly Customized Freestanding Hyperelastic Bioscaffold for Complex Craniomaxillofacial Reconstruction

Micro-extrusion 3D printing of articular cartilage substitutes with a multizonal structure using hydrophilic and rapidly curing silicone-based ink materials

4D printing of biocompatible, hierarchically porous shape memory polymeric structures

Electromagnetic assistance enables 3D printing of silicone-based thin-walled bioinspired soft robots