Abstract:The selective laser melted (SLM) 316L stainless steel (316L SS) has shown superior tensile ductility and doubled yield strength compared to its wrought counterpart. The significantly improved yield strength has been attributed to the unique cellular substructures featured by Cr/Mo-segregation and trapped dislocations. The excellent ductility of SLMed 316L SS has been mainly understood from the pronounced deformation twinning, which, however, is just one of the dominant plastic deformation mechanisms in 316L SS. Here instead, we report two other fundamental deformation micro-mechanisms, i.e., deformation faulting and dislocation cell refinement, in the SLM 316L SS. Our results showed that deformation faulting and dislocation cell refinement characterize the whole tensile deformation significantly except for deformation twinning. These newly found mechanisms synergistically dominated the deformation behavior at low strain levels while deformation faulting and twinning play a crucial role at medium and high strain levels. The pre-existing stacking faults (SFs) in cellular substructure is mainly responsible for the significant deformation faulting. At the early deformation stage, these pre-existing SFs provide faulting nuclei for deformation faulting, leading to wide SFs. These wide SFs in different cellular interiors penetrate the cellular boundaries and overlap as the strain increases, resulting in long stacking fault ribbons (SFRs). We attributed the formation of DCs to the measured medium stacking fault energy (SFE) of ∼18 mJ/m2. Upon straining, equiaxed dislocation cells (DCs) were generated by new dislocation cell walls (DCWs) inside the cellular substructure, and refined by either the dissociation of fully developed DCWs or the continuously formed new DCWs. Together with deformation twinning, these two fundamental deformation mechanisms jointly led to a steady strain hardening rate during tension and thus a superior tensile ductility of the SLM 316L SS with high yield strength. These findings provide new insights into the excellent strength-ductility combination of SLMed 316L SS and the experimental basis for crystal plasticity modeling and simulation, as well.

Energy Absorption and Deformation Behavior of 3D Printed Triply Periodic Minimal Surface Stainless Steel Cellular Structures under Compression

Energy absorption characteristics of metallic triply periodic minimal surface sheet structures under compressive loading

Double-Level Energy Absorption of 3D Printed TPMS Cellular Structures Via Wall Thickness Gradient Design

Mechanical Properties and Energy Absorption Abilities of Diamond TPMS Cylindrical Structures Fabricated by Selective Laser Melting with 316L Stainless Steel

The Influence of the Structure Parameters on the Mechanical Properties of Cylindrically Mapped Gyroid TPMS Fabricated by Selective Laser Melting with 316L Stainless Steel Powder

Improved light-weighting potential of SS316L triply periodic minimal surface shell lattices by micro laser powder bed fusion

Compressive behavior of selective laser melting printed Gyroid structures under dynamic loading

Compression and resilient behavior of graded triply periodic minimal surface structures with soft materials fabricated by fused filament fabrication

Achieving Triply Periodic Minimal Surface Thin-Walled Structures by Micro Laser Powder Bed Fusion Process

Topological and Mechanical Properties of Different Lattice Structures Based on Additive Manufacturing

Effect of residual stress on mechanical properties of Triply periodic minimal surface lattice structures in Additive manufacturing

Experimental and numerical studies on mechanical properties of TPMS structures

Design and Compression Behavior Exploration of Skeletal and Sheet TPMS Structures

Effect of heat treatment on compression properties of the 316L diamond structure fabricated through selective laser melting

An Experimental and Numerical Investigation of Compressive Response of Designed Schwarz Primitive Triply Periodic Minimal Surface with Non-Uniform Shell Thickness

Finite element analysis of the mechanical properties of sheet- and skeleton-gyroid Ti6Al4V structures produced by laser powder bed fusion

Investigation of Energy Absorbing Characteristics and Damage Mechanisms of Triply Periodic Minimal Surface Structures fabricated by Powder Bed Fusion Technology

Deformation faulting and dislocation-cell refinement in a selective laser melted 316L stainless steel

Novel triply periodic minimal surfaces sandwich structures: Mechanical performance and failure analysis

Design and Compression Behavior Exploration of Skeletal and Sheet Triply Periodic Minimal Surface Structures

Mechanical responses of sheet-based gyroid-type triply periodic minimal surface lattice structures fabricated using selective laser melting