Size-controlled Synthesis of Porous ZnSnO3 Nanocubes for Improving Formaldehyde Gas Sensitivity.

Jiaoling Zheng,Huanhuan Hou,Hao Fu,Liping Gao,Hongjie Liu

DOI: https://doi.org/10.1039/d1ra01852c

IF: 4.036

2021-01-01

RSC Advances

Abstract:The size of the ZnSnO3 nanocubes is about 100 nm with the corresponding specific surface area of 70.001 m2 g−1. A gas sensor based on porous ZnSnO3 nanocubes shows high sensitivity and selectivity to formaldehyde.

What problem does this paper attempt to address?

Enhanced gas sensing properties for formaldehyde based on ZnO/Zn2SnO4 composites from one-step hydrothermal synthesis

Xin Li,Nan Zhang,Caixia Liu,Samira Adimi,Jingran Zhou,Dali Liu,Shengping Ruan

DOI: https://doi.org/10.1016/j.jallcom.2020.156606

IF: 6.2

2021-01-01

Journal of Alloys and Compounds

Abstract:Formaldehyde gas sensor with high performance is indispensable for monitoring indoor air quality. Exploring novel nanostructured composites as gas sensing materials is considered to be a feasible way to enhance the sensing performance. In this work, one-step hydrothermal method was employed for facile synthesis of ZnO/Zn2SnO4 nanocomposites and the as-prepared sample took on a homogeneous hexagonal lamellar nanostructure with a diameter of 600 nm–900 nm and thickness of about 100 nm. Gas sensing properties of the sample were tested and the results demonstrated that the ZnO/Zn2SnO4 composites possessed excellent sensing performances to formaldehyde. At 160 °C, the ZnO/Zn2SnO4 composites based sensor exhibited a high response of 22.5 towards 100 ppm of formaldehyde and a detection limit as low as 500 ppb. Compared with pristine Zn2SnO4 and ZnO, ZnO/Zn2SnO4 composites showed higher sensitivity (increased by 80% and 120%), better selectivity and lower detection limit. The noteworthy improvement of formaldehyde sensing performances could be attributed to the synergetic effect as well as the formation of n-n type heterojunctions between Zn2SnO4 and ZnO. The mechanism involved in gas sensing performance of ZnO/Zn2SnO4 composites was also discussed.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Preparation and gas-sensitive properties of hollow Zn2SnO4/SnO2 nano-cubes

Dianpu Ma,Lang Zhang,Juntao Hu,Zewei Fu,Tan Luo,Di Yang,Dong Fang,Jun Li,Jubo Peng,Yingwu Wang

DOI: https://doi.org/10.1016/j.inoche.2022.109507

IF: 3.428

2022-04-01

Inorganic Chemistry Communications

Abstract:Metal oxide semiconductors with porous or hollow heterostructures can significantly improve the gas sensing performance of materials by promoting the increase of free electron density and the diffusion of test gas. Firstly, ZnSn(OH)6 was synthesized by one-step hydrothermal method, then hollow Zn2SnO4/SnO2 nano-cubes with the n-n heterojunction between Zn2SnO4 and SnO2 grains was obtained by calcination in air. The Zn2SnO4/SnO2 sensor possesses good response (Ra/Rg) toward ethanol and formaldehyde compare to other volatile organic compound (VOC) gas. In detail, the Ra/Rg is 11.12 and 9.16 in 100 ppm 200 °C ethanol and formaldehyde, respectively. Moreover, the repeatability, stability and ambient humidity as well as enhancement mechanism of this sensor are systematically discussed. These results indicate that Zn2SnO4/SnO2 nano-cubes with hollow structure is a promising sensing material for VOC gas detection.

chemistry, inorganic & nuclear
Formaldehyde gas sensors based on SnO2/ZSM-5 zeolite composite nanofibers

Yanhui Sun,Jing Wang,Haiying Du,Xiaogan Li,Chen Wang,Tengyue Hou

DOI: https://doi.org/10.1016/j.jallcom.2021.159140

IF: 6.2

2021-07-01

Journal of Alloys and Compounds

Abstract:An additional layer of zeolite on the surface of metal oxides results in an increased selectivity as gas sensors. However, there is insufficient knowledge on how interactions between the zeolite and gas-sensitive materials improve gas sensing properties. To increase the area of the interface between the materials and decrease agglomeration, SnO2/ZSM-5 composite nanofibers were synthesized via an electrospinning technique. "Bone joints," such as ZSM-5 nanoparticles, were present in the composite nanofibers. Analyses of the gas sensing properties show that the selectivity and sensitivity of the sensors to formaldehyde were improved. Electronic surface states and charge transport properties were measured via X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS), respectively. It was inferred from the XPS results that the adsorbed oxygen on the surface of the composite increased considerably, thus improving the sensitivity of the sensors. The results of the EIS and electrical equivalent circuits indicate that the interface of the two materials plays a significant role. A larger interfacial area between the zeolite and SnO2 can increase electron transfer and enhance the sensitivity and selectivity of the sensors. This study provides a strategy to improve the sensing properties of semiconducting metal oxide gas sensors.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Design of a SnO2/Zeolite Gas Sensor to Enhance Formaldehyde Sensing Properties: From the Strategy of the Band Gap-Tunable Zeolite.

Yanhui Sun,Yue Hou,Shouhang Fu,Jiawen Cui,Zhixin Luo,Zefeng Lei,Shupeng Sun

DOI: https://doi.org/10.1021/acsami.3c12789

2023-11-07

Abstract:ZSM-5 zeolite is usually used in gas sensors as an auxiliary material to improve the gas-sensitive properties of other semiconductor materials, such as its molecular sieve properties and surface adsorption properties. Here, the gas-sensitive mechanism analysis of SnO2/zeolite gas sensors is studied for the first time based on the perspective of zeolite as a band gap-tunable semiconductor that was reported recently. The gas-sensing mechanism of the zeolite/semiconductor has been modeled based on the surface charge theory, and the work function of the ZSM-5 zeolite has been revealed for the first time. A heterostructure of Ag and ZSM-5 was designed and compounded to tune the band gap of the ZSM-5 zeolite by the ammonia pool effect method. The band gap width of the zeolite decreases from 4.51 to 3.61 eV. A series of characterization techniques were used to analyze the distribution and morphology of silver nanoparticles in zeolites and the variation of the ZSM-5 band gap. Then, SnO2/Ag@ZSM-5 sensors were fabricated, and the gas-sensing performances were measured. The gas-sensing results show that the SnO2/Ag@ZSM-5 sensor has an improved response to formaldehyde in particular compared to the SnO2 sensor. The response value of the SnO2/Ag@ZSM-5 sensor to 70 ppm formaldehyde reached 29.4, which is a 528% improvement compared to the SnO2 sensor. Additionally, the selectivity was greatly enhanced. This study provides a strategy for designing and developing higher-performance gas sensors.

Medicine,Materials Science,Engineering,Chemistry
The Improvement of Gas-Sensing Properties of SnO 2 /Zeolite-Assembled Composite

Yanhui Sun,Jing Wang,Xiaogan Li,Haiying Du,Qingpan Huang

DOI: https://doi.org/10.1007/s11051-018-4240-4

IF: 2.533

2018-01-01

Journal of Nanoparticle Research

Abstract:SnO2-impregnated zeolite composites were used as gas-sensing materials to improve the sensitivity and selectivity of the metal oxide-based resistive-type gas sensors. Nanocrystalline MFI type zeolite (ZSM-5) was prepared by hydrothermal synthesis. Highly dispersive SnO2 nanoparticles were then successfully assembled on the surface of the ZSM-5 nanoparticles by using the impregnation methods. The SnO2 nanoparticles are nearly spherical with the particle size of ~ 10 nm. An enhanced formaldehyde sensing of as-synthesized SnO2-ZSM-5-based sensor was observed whereas a suppression on the sensor response to other volatile organic vapors (VOCs) such as acetone, ethanol, and methanol was noticed. The possible reasons for this contrary observation were proposed to be related to the amount of the produced water vapor during the sensing reactions assisted by the ZSM-5 nanoparticles. This provides a possible new strategy to improve the selectivity of the gas sensors. The effect of the humidity on the sensor response to formaldehyde was investigated and it was found the higher humidity would decrease the sensor response. A coating layer of the ZSM-5 nanoparticles on top of the SnO2-ZSM-5-sensing film was thus applied to further improve the sensitivity and selectivity of the sensor through the strong adsorption ability to polar gases and the “filtering effect” by the pores of ZSM-5.
Hierarchical Porous NiO Doped ZnO Nanocomposite for Formaldehyde Gas Sensor with High Sensitivity, Fast Response/recovery and Good Selectivity

Benzheng Li,Hongbiao Liu,Qingrui Zeng,Shuangshi Dong,Wei Feng

DOI: https://doi.org/10.1016/j.surfin.2022.102502

IF: 6.2

2023-01-01

Surfaces and Interfaces

Abstract:Formaldehyde (HCHO) is a kind of indoor pollution gas which seriously harms human health. High properties gas sensor for formaldehyde are essential for indoor air quality monitoring. The development of new nano-structured composites as gas sensing materials is seen as a viable way to improve sensing performance. In this study, a new type of layered porous nickel oxide doped zinc oxide nanocomposite with sunflower straw as a template (SFS NiO/ZnO) was synthesised. The structure and morphology of the material was characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). These results exhibit that the synthetic SFS NiO/ZnO successfully maintains the original pore morphology of the sunflower straw material and the framework consists of a large number of nanoparticles of uniform size and shape. The gas sensing performance of the prepared samples was tested and the results showed that the SFS NiO/ ZnO biocomposite had promising sensing performance for formaldehyde. The response of the SFS NiO/ZnO gas sensor working at 240 degrees C was 42 for 100 ppm formaldehyde with response and recovery times of 9 s and 8 s, respectively. The lower limit of detection is 148 ppb. Compared with SFS ZnO, the significant improvement of formaldehyde sensing properties could be attributed to its increased oxygen vacancy concentration and the presence of p-n type heterojunctions.
Perovskite-type ZnSn(OH)6 Hollow Cubes with Controllable Shells for Enhanced Formaldehyde Sensing Performance at Low Temperature

Liyong Du,Kuikun Gu,Mingming Zhu,Jing Zhang,Mingzhe Zhang

DOI: https://doi.org/10.1016/j.snb.2019.03.009

IF: 9.221

2019-01-01

Sensors and Actuators B Chemical

Abstract:Perovskite-type ZnSn(OH)(6) has attracted a lot of attention due to its exceptive electronic structure. In this work, ZnSn(OH)(6) hollow cubes with different shell numbers have been synthesized by repeated co-precipitation and alkaline etching at room temperature without any additional templates. Gas sensing performance of ZnSn(OH)(6) cubes with different shell numbers is compared, interestingly, gas sensing properties increase with increasing the shell numbers. As is expected, the sensor based on multi-shelled ZnSn(OH)(6) nanocubes not only shows the high response of 56.6-100 ppm formaldehyde and excellent selectivity, but also exhibits rapid response time (1 s) and selective to formaldehyde at its low concentration (100 ppm) at a low operating temperature of 60 degrees C. These excellent properties are mainly due to multilevel and hollow structure, the cube/cube junction and oxygen vacancies on the surface, which make them a promising material for formaldehyde sensors.
Metal-organic Framework-Derived Porous SnO2 Nanosheets with Grain Sizes Comparable to Debye Length for Formaldehyde Detection with High Response and Low Detection Limit

Xiaojie Zhu,Xinlu Zhang,Xueting Chang,Junfeng Li,Likun Pan,Yingchang Jiang,Weixiang Gao,Chenyang Gao,Shibin Sun

DOI: https://doi.org/10.1016/j.snb.2021.130599

2021-01-01

Abstract:The development of metal oxide semiconductors-based gas sensors that can simultaneously achieve high response and low detection limit towards formaldehyde (HCHO) remains a great challenge so far. In this work, we present the formation of porous SnO2 nanosheets via direct calcination of a Sn-based metal-organic framework that was prepared via a facile wet chemistry method with deionized water as solvent at 80 degrees C. The porous SnO2 nanosheets are found to be constructed by the interconnection of ultrafine nanoparticles with sizes of 4-9 nm, which is comparable to the Debye length of SnO2. The gas sensor based on the porous SnO2 nanosheets demonstrate a broad detection range towards HCHO (0.05-500 ppm), a low operating temperature (140 degrees C), very high response (540.8 to 50 ppm HCHO), extremely low detection limit (0.31 ppb), ideal selectivity, and outstanding reproducibility and durability. The excellent HCHO-sensing performance of the SnO2 sensor could be attributed to the high specific surface area (125.92 m2/g) of the porous SnO2 nanosheets, the ultrafine sizes of the SnO2 nanoparticles, and the presence of abundant of mesopores within the nanosheets. The porous SnO2 nanosheets with excellent HCHO-sensing characteristics may find widespread applications in fabricating gas sensors for detecting ppb-level HCHO.
Pore-size-dependent Sensing Property of Hierarchical SnO2 Mesoporous Microfibers As Formaldehyde Sensors

Shouqin Tian,Xiaohu Ding,Dawen Zeng,Shunping Zhang,Changsheng Xie

DOI: https://doi.org/10.1016/j.snb.2013.06.073

2013-01-01

Abstract:Distinct from SnO2 nanoparticulates whose gas-sensing properties depend deeply on grain size and specific surface area, hierarchical SnO2 mesoporous structures has been found to possess remarkable gas-sensing performance due to their large accessible surface area. Interestingly, our obtained hierarchical SnO2 mesoporous microfibers shows an increase in the response to formaldehyde (HCHO) gas with decreasing specific surface area and increasing pore size, characterized by TEM, BET and performance analysis. The pore-size-dependent gas-sensing properties are mainly attributed to the transport of detected gases inside SnO2 mesoporous microfibers. Smaller pores can not provide efficient gas transport to more active sites while larger pores can allow most detected gas molecules diffuse easily inside the deeper region of the mesoporous SnO2 microfibers and react with oxygen species adsorbed on the surface (these reactive surface can be called as effective surface), resulting in a large sensor response. Therefore, the pore size and its resultant effective surface area rather than specific surface area play a dominant role in the gas-sensing properties of mesoporous materials, which can provide us with new insight on the design of high-performance gas sensors in the future.
Unique Hierarchical Sn3O4 Nanoflowers Decorated with ZnO Nanoparticles and Their Formaldehyde Gas Sensing Properties

Lei Wang,Yang Li,Song Gao,Wenjing Yue

DOI: https://doi.org/10.1088/1757-899x/729/1/012103

2020-01-01

IOP Conference Series Materials Science and Engineering

Abstract:Abstract Gas sensors with high response are highly desirable for the detection of harmful gases in real-time. Herein, the ZnO nanoparticles decorated hierarchical Sn3O4 nanoflowers are synthesized by a hydrothermal method. The gas sensor based on the ZnO/Sn3O4 composites exhibits excellent sensing properties to formaldehyde with a low operating temperature of 180°C. Specifically, the sensor has a response value of 44 for 100 ppm formaldehyde and a fast response time of 5 s. Moreover, it is noteworthy that the proposed gas sensor shows a wide detection range and a low detection limit of 1 ppm. Besides, the ZnO/Sn3O4 sensor exhibits good selectivity for formaldehyde and perfect reproducibility. The sensing mechanism of the gas sensor is discussed, and the heterojunction between ZnO and Sn3O4 enhances the sensing performance of the proposed gas sensor.
SnO2 mesoporous nanoparticle-based gas sensor for highly sensitive and low concentration formaldehyde detection

Pengfei Liu,Jianbin Wang,Han Jin,Meiying Ge,Fang Zhang,Cheng Wang,Yan Sun,Ning Dai

DOI: https://doi.org/10.1039/d2ra06745e

IF: 4.036

2023-01-14

RSC Advances

Abstract:Indoor air quality detection, especially formaldehyde (HCHO) detection, is of great importance in practical application. A key limitation of promoting gas-sensing devices is the lack of sensing materials with high sensing sensitivity and selectivity. In this study, SnO 2 mesoporous nanoparticles are fabricated by a facile hydrothermal route with a subsequent acid etching process. The prepared samples show high response toward HCHO (133.5, 222.8 for 100 ppm and 200 ppm HCHO, respectively) and short response/recovery time (15/22 s at 10 ppm). The excellent HCHO sensing performance benefits from the comprehensive regulation of the depletion region width, surface area and rich porosity, which is effective for the promotion of surface adsorption and catalyst activity. It is expected that the excellent sensing properties are promising for practical HCHO gas detection.

chemistry, multidisciplinary
Biotemplates Based Preparation of Hierarchical ZnSnO3 Porous Nanostructures for Fast Detection of Formaldehyde

Liyong Du,Yingai Li,Yu Tong,Mingzhe Zhang

DOI: https://doi.org/10.1016/j.ceramint.2021.01.178

IF: 5.532

2021-01-01

Ceramics International

Abstract:The synthesis of hierarchically porous nanostructures is always highly concerned by researchers. Herein, we report a simple, low-cost and green approach to obtain hierarchical ZnSnO3 porous nanostructures by using the branches of pterocarya stenoptera, catalpa and apricot as biotemplate, respectively. The gas sensing properties of hierarchical ZnSnO3 porous nanostructures are systematically analyzed. The results exhibit that the ZnSnO3 based gas sensors show not only high responses and rapid response/recovery speed (2/8 s for ZnSnO3-1, 1/10 s for ZnSnO3-2 and 2/20 s for ZnSnO3-3) at the working temperature of 240oC but also excellent anti-humidity properties, gas selectivity, repeatability and long-term stability. Besides, the linear relationship between the responses and the formaldehyde concentration (1?200 ppm) is observed. The excellent gas sensing performance of the ZnSnO3 based gas sensors is mainly ascribed to the unique structural merits. The simple synthetic method in this paper also provides implications for the design and synthesis of porous MOSs.
High response to formaldehyde gas and ppb-level detectability of nanoparticle Cr2O3/ porous cubic ZnSnO3 composites p-n heterojunction gas sensor

Lili Jiang,Ruijia Zhang,Wenqiang Zhang,Jiahao Yang,Haiqing Jiang,Zhengbiao Hu,Yingying Zhang

DOI: https://doi.org/10.1016/j.ceramint.2023.12.045

IF: 5.532

2023-12-01

Ceramics International

Abstract:A series of chromium trioxide/zinc metastannate (Cr2O3/ZnSnO3) composites with different ratios were prepared via a simple two-step hydrothermal and high-temperature sintering method. The samples underwent characterization and analysis to assess their micromorphologies, elemental distributions, chemical compositions, and specific surface areas. Furthermore, gas sensing properties were evaluated through experiment. Results showed that the cubic ZnSnO3 block in Cr2O3/ZnSnO3 was in close contact with the surface of nanoparticulate Cr2O3 and the specific surface area increases. Its primary elements are Zn, Sn, Cr, and O. The 15 wt% Cr2O3/ZnSnO3 sensor exhibited an optimal operating temperature of 175 °C, 75 °C lower than that of pure ZnSnO3 (250 °C). The 15 wt% Cr2O3/ZnSnO3 sensor exhibited the best sensing performance for formaldehyde gases with a concentration of 50 ppm. It exhibited a response of 37.8 and could detect ppb-level concentrations of formaldehyde (limit of detection = 612 ppb). Additionally, Cr2O3/ZnSnO3 showed good selectivity for formaldehyde in the presence of six gases, that is, acetone, formaldehyde, methanol, ethanol, ammonia, and carbon monoxide. Cr2O3/ZnSnO3 exhibited good short-term repeatability and long-term stability. Because of the excellent performance of Cr2O3/ZnSnO3 composites, they have broad application prospects in formaldehyde gas detection.

materials science, ceramics
Enhanced ppb-level formaldehyde sensing performance over Pt deposited SnO2 nanospheres

Yunxiang Tang,Zejun Han,Yuan Qi,Zhengyi Yang,Hecheng Han,Yanyan Jiang,Xue Zhang,Lili Wu,Zhou Wang,Jiurong Liu,Fenglong Wang

DOI: https://doi.org/10.1016/j.jallcom.2021.163230

IF: 6.2

2022-01-01

Journal of Alloys and Compounds

Abstract:Formaldehyde is one of the most serious threats to human health in modern interior decoration. Thereby, online detection of indoor formaldehyde concentration has become an urgent problem. In this work, the Pt deposited porous SnO2 nanospheres were synthesized as the formaldehyde sensing materials, which were prepared by hydrothermal and chemical reduction methods. The diameter of as-synthesized Pt-SnO2 were centered in the range of 30-50 nm, with the dominant pore size of similar to 10 nm and the specific surface area of 89.79 m(2) g(-1), which provided a raft of passages and active sites for gas molecules to diffuse and interact mutually. Moreover, the experimental results demonstrated that the 1 wt.% Pt-SnO2 exhibited higher response (16.03), high-speed response time (9 s) and outstanding selectivity with exposure to low-concentration formaldehyde compared with original SnO2. The porous structures and catalytic effect of Pt nanoparticles were jointly responsible for the enhancement of SnO2 on sensing performance towards formaldehyde. (C) 2021 Elsevier B.V. All rights reserved.
Hollow ZnSnO3 Cubes with Controllable Shells Enabling Highly Efficient Chemical Sensing Detection of Formaldehyde Vapors

Tingting Zhou,Tong Zhang,Rui Zhang,Zheng Lou,Jianan Deng,Lili Wang

DOI: https://doi.org/10.1021/acsami.7b03112

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:In structural hierarchy, inherently hollow nanostructured materials preferentially possessing high surface area demand attention due to their alluring sensing performances. However, the activity of hollow and structural hierarchy nanomaterials generally remains suboptimal due to their hollow space structure and large lateral size, which greatly hamper and limit the availability of inner space active sites. Here, hollow ZnSnO3 cubes with a controllable interior structure were successfully prepared through a simple and low-cost coprecipitation approach followed with a calcination process. The solid-, single-, double-, and multishelled ZnSnO3 hollow cubes could be selectively tailored by repeated addition of alkaline solution. The multishelled architecture displayed outstanding sensing properties for formaldehyde vapors due to large specific surface area, less agglomerations, abundant interfaces, thin shells, and high proportion porous structure, which act synergistically to facilitate charge transfer and promote target gas adsorption.
Gas-Sensitive Properties of ZnO/ZnCo 2 O 4 Made from Sodium Citrate Against Formaldehyde

Xin Ma,Zhihua Ying,Fei Wen,Lili Li,Xiaolong Zheng,Peng Zheng,Gaofeng Wang

DOI: https://doi.org/10.1007/s11664-022-09930-y

IF: 2.1

2022-01-01

Journal of Electronic Materials

Abstract:Since cobalt-containing spinel oxides have good prospects for the detection of toxic gases, they also have great potential for applications in the field of gas sensors. However, ZnCo 2 O 4 -based gas sensors have the disadvantages of low response values and poor selectivity in formaldehyde detection. In this study, we attempted to prepare formaldehyde gas sensors by varying the addition of sodium citrate for hydrothermal synthesis of ZnCo 2 O 4 . During the fabrication process, it was found that an appropriate amount of sodium citrate content could produce ZnO on the surface of ZnCo 2 O 4 , and that the gas sensitivity of ZnO-ZnCo 2 O 4 to formaldehyde was better compared to that of pure ZnCo 2 O 4 . The sensor has a response rate of 17 at 20 ppm formaldehyde at 200°C. It also has good selectivity, repeatability, and stability. These results can provide foundational knowledge for the implementation of spinel oxide materials in the field of gas sensors.
Highly reactive 0D ZnS nanospheres and nanoparticles for formaldehyde gas-sensing properties

Shahid Hussain,Tianmo Liu,Muhammad Sufyan Javed,Nimra Aslam,Wen Zeng

DOI: https://doi.org/10.1016/j.snb.2016.09.128

2017-01-01

Abstract:Wurtzite zero dimensional ZnS nanospheres and random-shaped nanoparticles successfully synthesized via a low temperature hydrothermal route. The formation of nanostructures is attributed due to PVP and thiourea and discussed in details. The as-prepared nanostructures were characterized by XRD, EDS, SEM and HRTEM. Based on experimental results, a plausible growth mechanism is also proposed along with crystal structure of ZnS. The gas-sensing properties of as-prepared ZnS products are tested using efficient substrate sensors via an intelligent gas testing system. Both at room and 100-400 degrees C temperature, high response and selectivity towards formaldehyde than other gases is observed. Comparative studies of ZnS nanostructures for different concentrations of formaldehyde gas and definite sensor-stability for different gases is studied, as well. (C) 2016 Elsevier B.V. All rights reserved.
Three dimensions sphere formaldehyde nanosensor applications: preparation and sensing properties

ying wang,dingsheng jiang,wei wei,linghui zhu,liang shen,shanpeng wen,shengping ruan

DOI: https://doi.org/10.1039/c5ra07852k

IF: 4.036

2015-01-01

RSC Advances

Abstract:Zn@SnO2 microspheres with hierarchical structure were prepared through a simple solvothermal method; the structure and morphology were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and high resolution transmission electron microscopy (HRTEM) showing the materials with extraordinary 3D nanoarchitectures. The gas sensing properties of the as-prepared pure SnO2 and Zn-doped SnO2 were tested toward various gases. The results showed that the SnO2 sensor with 6.67 wt% Zn-doping displayed an excellent selectivity toward formaldehyde at the operating temperature 160 degrees C, which was considerably lower than most formaldehyde sensors in heater type among previous reports, in addition to giving a response of about 15.2 to 100 ppm, which is about 2.1 times higher than that of sensors based on pure SnO2. The tau(res) and the tau(rec) values of the 6.67 wt% Zn-doped SnO2 sensor to 100 ppm formaldehyde were 2 s and 2 s respectively, demonstrating extraordinary gas sensing properties, whereas those of the pure SnO2 sensor were relatively long. The enhancement might be attributed to the unique morphology and increased oxygen vacancy due to the Zn doping.
UV activated formaldehyde gas sensing based on gold decorated ZnO@ In 2 O 3 hollow nanospheres at room temperature

Lijia Zhao,Shupeng Sun,Su Zhang,Xiaogan Li

DOI: https://doi.org/10.1016/j.snb.2024.136149

IF: 9.221

2024-06-19

Sensors and Actuators B Chemical

Abstract:Using uniform carbon nanospheres as sacrificial templates, gold nanoparticle-modified ZnO@ In 2 O 3 hollow nanospheres with controlled dimensions and porous architectures were successfully synthesized through water bath, hydrothermal and chemical reduction methods. Gas sensing evaluation revealed that the Au-decorated ZnO@ In 2 O 3 hollow nanostructures exhibited a dramatically amplified response up to 14.8 when exposed to 10 ppm formaldehyde analyte at room temperature. Furthermore, multifaceted performance benefits of Au-decorated ZnO@ In 2 O 3 over single-phase ZnO, Au-ZnO, ZnO@ In 2 O 3 heterojunction-based composites were observed, including excellent selectivity towards formaldehyde even in complex gas mixtures; tremendous sensitivity enhancement stemming from synergies between efficient gas diffusion through hollow heterojunction nanospheres and accelerated surface reactions at catalytically-active Au sites; and rapid, fully-reversible response/recovery time of 32 s and 42 s, respectively. In-depth investigations were conducted into the fundamental sensing mechanisms enabling formaldehyde detection using AC impedance spectroscopy, in situ diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS), and density functional theory (DFT) computational modelling analyses.

chemistry, analytical,electrochemistry,instruments & instrumentation
Study on the Gas-Sensitive Properties for Formaldehyde Based on SnO2-ZnO Heterostructure in UV Excitation

Jingjing Jiang,Linqi Shi,Tengfeng Xie,Dejun Wang,Yanhong Lin

DOI: https://doi.org/10.1016/j.snb.2017.07.197

2018-01-01

Abstract:The polyporous SnO2-ZnO composites were synthesized by a water-bath method. The 3D center-hollow architecture and polyporous surface were also confirmed by field-emission scanning electron microscope (FE-SEM) and the Brunauer-Emmett-Teller (BET) specific surface area. Meanwhile, structural properties of SnO2-ZnO have been investigated by trans-mission electron microscopy (TEM) in 1 mol% SnO2-ZnO. The results of photoelectric gas-sensing demonstrated that the 1 mol% SnO2-ZnO gas-sensor exhibits not only an excellent response to formaldehyde (HCHO) but also superior sensitivity to low HCHO concentration. The response of 1 mol% SnO2-ZnO for the 1 ppm HCHO has reached 30% at room temperature (25 degrees C), and a detection limit of 0.1 ppm HCHO was achieved. The behavior of photogenerated charge is discussed in detail by means of the surface photovotage (SPV) and the transient photovoltage (TPV) techniques. It was found that the as-prepared 1 mol% SnO2-ZnO composites showed excellent separation and transfer efficiency of photogenerated charges carriers. What's more, the TPV spectrum analysis provides convincing evidence that the addition of excess SnO2 is unfavorable to the transfer of electrons so as to reduce the sensitivity of SnO2-ZnO for target gas. This result offers a new window to explain the effect of SnO2 concentration on the gas sensing characteristics, and provide more information on the fabricating composite materials for gas sensors. (C) 2017 Elsevier B.V. All rights reserved.

Size-controlled Synthesis of Porous ZnSnO3 Nanocubes for Improving Formaldehyde Gas Sensitivity.

Enhanced gas sensing properties for formaldehyde based on ZnO/Zn2SnO4 composites from one-step hydrothermal synthesis

Preparation and gas-sensitive properties of hollow Zn2SnO4/SnO2 nano-cubes

Formaldehyde gas sensors based on SnO2/ZSM-5 zeolite composite nanofibers

Design of a SnO2/Zeolite Gas Sensor to Enhance Formaldehyde Sensing Properties: From the Strategy of the Band Gap-Tunable Zeolite.

The Improvement of Gas-Sensing Properties of SnO 2 /Zeolite-Assembled Composite

Hierarchical Porous NiO Doped ZnO Nanocomposite for Formaldehyde Gas Sensor with High Sensitivity, Fast Response/recovery and Good Selectivity

Perovskite-type ZnSn(OH)6 Hollow Cubes with Controllable Shells for Enhanced Formaldehyde Sensing Performance at Low Temperature

Metal-organic Framework-Derived Porous SnO2 Nanosheets with Grain Sizes Comparable to Debye Length for Formaldehyde Detection with High Response and Low Detection Limit

Pore-size-dependent Sensing Property of Hierarchical SnO2 Mesoporous Microfibers As Formaldehyde Sensors

Unique Hierarchical Sn3O4 Nanoflowers Decorated with ZnO Nanoparticles and Their Formaldehyde Gas Sensing Properties

SnO2 mesoporous nanoparticle-based gas sensor for highly sensitive and low concentration formaldehyde detection

Biotemplates Based Preparation of Hierarchical ZnSnO3 Porous Nanostructures for Fast Detection of Formaldehyde

High response to formaldehyde gas and ppb-level detectability of nanoparticle Cr2O3/ porous cubic ZnSnO3 composites p-n heterojunction gas sensor

Enhanced ppb-level formaldehyde sensing performance over Pt deposited SnO<sub>2</sub> nanospheres

Hollow ZnSnO3 Cubes with Controllable Shells Enabling Highly Efficient Chemical Sensing Detection of Formaldehyde Vapors

Gas-Sensitive Properties of ZnO/ZnCo 2 O 4 Made from Sodium Citrate Against Formaldehyde

Highly reactive 0D ZnS nanospheres and nanoparticles for formaldehyde gas-sensing properties

Three dimensions sphere formaldehyde nanosensor applications: preparation and sensing properties

UV activated formaldehyde gas sensing based on gold decorated ZnO@ In 2 O 3 hollow nanospheres at room temperature

Study on the Gas-Sensitive Properties for Formaldehyde Based on SnO2-ZnO Heterostructure in UV Excitation