Abstract:In general, single crystal shape memory alloys exhibit superior shape memory effect and superelasticity when compared to their polycrystalline counterparts. However, it is challenging and costly to prepare a single crystal in traditional ways, such as the Czochralski method and directional solidification technique. Recently, cyclic heat treatment (CHT) has emerged as a facile and cost-effective method to fabricate single crystal by inducing abnormal grain growth. In the present work, we aimed to fabricate Fe-Mn-Al-Cu single crystals utilizing the CHT technique. Single crystal Fe-Mn-Al-Cu shape memory alloys were successfully prepared, and the effect of CHT parameters on abnormal grain growth was investigated. It was revealed that increasing the cooling rate resulted in a non-monotonic response in the maximum grain size, which initially increased and was followed by a subsequent decrease. This behavior was attributed to the subgrain refinement, increase in subgrain misorientation angles, and the narrowing of the low density zones (LDZs) of subgrains. Decreasing the lower temperature of CHT caused similar trends in maximum grain size, due to the increase in subgrain misorientation angle and the expansion of the LDZs. Extending the holding time at the lower temperature of CHT had minimal impact on grain size. Increasing the heating rate of CHT resulted in a reduction in the maximum grain size because of the narrowing of the LDZs. Moreover, the addition of 2 wt% Cu led to a reduction of the maximum grain size, attributing to the decreased solvus temperature of the γ phase as a result of Cu addition. Consequently, the γ phase and subgrains were refined, and the LDZs were narrowed.

Structure Analysis And Shape Memory Effect Of Electropulse Modifying Fabricated Cu-Al-Ni Alloys

Electropulse Modification of Polycrystalline Cualni Shape-Memory Alloy, Its Macro- and Microstructure

Macrostructures and shape memory effect of cast-state electropulse modified Cu-Al-Ni alloys

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Effect of electropulse modification parameters on ingot macrostructure of Cu-Al-Ni shape memory alloys

Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

Effect of element evaporation on the microstructure and properties of CuZnAl shape memory alloys prepared by selective laser melting

Influence of microstructure on elastocaloric and shape memory effects in Mn50Ni32Sn7Co11 alloys

Electron beam freeform fabrication of NiTi shape memory alloys: Crystallography, martensitic transformation, and functional response

Structural and Phase Transformations and Physical and Mechanical Properties of Cu-Al-Ni Shape Memory Alloys Subjected to Severe Plastic Deformation and Annealing

Improved Ductility of Aged Mg-9Al-1Zn Alloy Strip by Electropulsing Treatment

Design and Development of High-Strength and Ductile Ternary and Multicomponent Eutectoid Cu-Based Shape Memory Alloys: Problems and Perspectives

Simultaneously enhancing the strength and ductility of Cu-Ti-Fe alloy through electric current pulse induced precipitation

Tuning the microstructure, martensitic transformation and superelastic properties of EBF3-fabricated NiTi shape memory alloy using interlayer remelting

Transformation Hysteresis and Shape Memory Effect of an Ultrafine-Grained Tininb Shape Memory Alloy

Effects of Ecae Process on Microstructure and Transformation Behavior of Tini Shape Memory Alloy

Fabrication of single-crystal Fe-Mn-Al-Cu alloys by cyclic heat treatments

Microstructure and Mechanical Properties of Ti–V–Al–Cu Shape Memory Alloy by Tailoring Cu Content

Microstructure, Shape Memory Effect and Mechanical Properties of Rapidly Solidified Co–Ni–Al Magnetic Shape Memory Alloys

Microstructure and texture evolution of cold-rolled Mg-3Al-1Zn alloy by electropulse treatment stimulating recrystallization

Microstructure and Shape Memory Properties of Cu-12.5Al-xMn Alloy Produced by Additive Manufacturing with Powder Core Wire