Dynamic Modeling For A High-Speed 3-Dof Parallel Robot With Compliant Joints

Yuan Li,Yue-Qing Yu

2014-01-01

Abstract:A dynamic model of a high-speed 3-DOF parallel robot with compliant joints was proposed based on Lagrange method. The virtual cutting method was used to make the calculation easier. The dynamic response was obtained and compared with Adams simulation. The dynamic model is verified in the comparison results.

What problem does this paper attempt to address?

Dynamic Modeling and Analysis for Coupling Processing 6-DOF 3 P3 R Manipulator

DING Pan,L(U) Fuzai,HUANG Kaiqiang,ZHAO DaXu

2011-01-01

Abstract:As the quick increase of the automatic requirement for the coupling processing lines,the automatic feeding and unloading 6-DOF 3P3R manipulator for coupling processing machine was designed.The kinematics and dynamics of the manipulator were analyzed,such as,operating performance and accurately motion control acquired.The Kane′s method and screw theory were applied to set up the kinematic and dynamic models,respectively.Then,in accordance with the models for the manipulator,and the structure of the prototype robot manipulator.The operating performance of the manipulator was studied in the mathematical environment.The orientation variation of the end-effectors and all joint driven torques of the system were obtained according to the planning motion.The result indicated that the correctness,simplicity and validity of the model is verified.Therefore,the dynamic requirements of the manipulator are satisfied with high dexterity.And this research established a foundation for trajectory planning and accurately motion control.
Dynamic Modeling of Overconstrained Parallel Robot

Jianxin Yang,Zhentao Liu,Jianwei Sun

DOI: https://doi.org/10.4028/www.scientific.net/amm.373-375.34

2013-01-01

Applied Mechanics and Materials

Abstract:The dynamic modeling method for parallel robot based on the principle of virtual work and equivalent tree structure is proposed by taking off the platform and the chains as well as degenerating parallel robot into a tree structure, the closed-form solutions for the inverse and forward dynamics models of parallel robot are derived. The method is applied on kinematics and dynamics analysis of a representative 3-RRR spherical parallel robot.
Error Modeling of Parallel Robots for Semi-Physical Simulation Platform of Space Docking Mechanism

Dayong Yu,Weifang Chen,Hongren Li

DOI: https://doi.org/10.1016/j.proeng.2011.08.082

2011-01-01

Procedia Engineering

Abstract:The parallel robot for semi-physical simulation platform of space docking mechanism is taken as the structure model, by treating each sun-chain of the parallel robot as a joint-link train, thus the error model in which structural parameter errors are considered is established from the kinematic equations and the loop properties of parallel structure. The error model is verified by computer simulation, and the results indicate that the error model established in this paper can approximately report the changing trend of the actual pose errors in the case where the parameter errors are small enough.
Dynamic Modeling of Flexible Parallel Robot

Hu Junfeng,Zhang Xianmin,Zhu Dachang,Chen Qiang

DOI: https://doi.org/10.3969/j.issn.1000-1298.2011.11.039

2011-01-01

Abstract:An accurate and simple method for dynamic modeling of general flexible parallel robot was proposed. According to the structural character of the parallel robot, it was devided into rigid sub-structure and elastic sub-structure, and the rigid-flexible coupling system was formed. The static platform and mobile platform were treated as rigid sub-structure because its deformations were smaller compared to the other part. The chains were treated as flexible sub-structure. The dynamic equations of each sub-structure were obtained, respectively. The dynamic equations of elastic sub-structure were obtained by using the finite element method and mode synthesis method. The dynamic equations of rigid sub-structure were built accounting for the effects of deformation of flexible sub-structure. The geometrical constraint relationship between three flexible sub-structures and the rigid platform was investigated to obtain a simple displacement and dynamic relation between them. The equations of all sub-structure were assembled to get the system dynamic equations. The comparative analysis of dynamic characteristics of a high-speed parallel manipulator show that the method is correct and feasible. Due to introducing the rigid sub-structure and application of the mode synthesis, the number of system freedom was reduced and the computational modeling was simplified. It provided a practical method for flexible parallel robot.
On The Method Of Linearizing Dynamic-Model And Solving Forward Dynamic Problems Of Flexible Robots

Jf Guo,Zf Tong

1995-01-01

International Journal of Robotics and Automation

Abstract:In this paper, a new way of linearizing the dynamic model of flexible robot is put forward. Based on linearization of the kinematic model, decoupled time-variant linear differential equations with only microvariables as generalized coordinates are deduced from general dynamic equations. The numerical computation of a three-link flexible robot arm for the forward dynamic problems is also carried out. The performance and capabilities of this method are tested through simulation analysis.
Dynamic Modeling and Simulation of a Hybrid Robot

Nanyan Shen,Hengming Yuan,Jing Li,Zirui Wang,Ninghe Lu,Yushun Lu

DOI: https://doi.org/10.1115/1.4054322

2022-01-01

Journal of Mechanisms and Robotics

Abstract:The unique structure of hybrid robot makes its dynamic characteristic different from that of the traditional machine tools. Therefore, the dynamic model is crucial to both designing and application of hybrid robot. In this paper, a new type of five-degrees-of-freedom (5DoF) hybrid robot is introduced, and its dynamic model is established. First, the kinematic formulas are derived for all the component, and then, the inertia forces or moments are calculated. Second, the active forces or moments in the joints are assumed as variables and the number of variables is reduced by analyzing joint types. Then, an equation set of 36 equilibrium equations with 38 variables is obtained using D'Alembert's principle. Based on the spatial deformation compatibility analysis of two branches, two supplementary equations are derived to determine the solution of dynamic model of the hybrid robot with redundant constraints in its parallel mechanism. Several cases are studied by comparing with ADAMS simulation. The result shows the good accuracy of the proposed dynamic model, which provides a practical method to calculate the reaction force or moment in any joint at any instant for the hybrid robot and thus facilitates dimensional synthesis, trajectory optimization, and smoothing control.
Dynamic Modeling of a Parallel Manipulator with Two Translational Degrees of Freedom

王启明,汪劲松,刘辛军,王立平

DOI: https://doi.org/10.3321/j.issn:1000-0054.2002.11.015

2002-01-01

Abstract:The dynamics of a parallel manipulator with two translational degrees of freedom was investigated using the Lagrange multiplier approach. Since the algorithm does not use a coordinate transformation between the joint space and Cartesian space, it increases the calculational efficiency so that realtime control can be realized. The algorithm was applied to a modular parallel mechanism with high rigidity and high flexibility to predict the position, velocity, acceleration and Jacobian matrix of the manipulator. A closed form dynamic model was presented based on the generalized system coordinates. The dynamic simulation shows the relation between the joint actuating force and the process parameters such as the platform trajectory and the manipulator mass and acceleration.
Dynamic Model of a 3-DOF Redundantly Actuated Parallel Manipulator

Tiemin Li,Shi Jia,Jun Wu

DOI: https://doi.org/10.1177/1729881416662791

IF: 1.714

2016-01-01

International Journal of Advanced Robotic Systems

Abstract:We investigate the dynamic mode of a 3-degree of freedom (DOF) redundantly actuated parallel manipulator by taking the flexible deformation of the limbs into account. The dynamic model is derived using Newton–Euler formulation. Since the number of equations derived from the force and moment equilibrium of the parallel manipulator components is less than the number of unknown variables, the flexible deformation of the limbs is treated as an inequality constraint to find the solution of the dynamic model. The errors of moving platform caused by the flexible deformation of limbs are discussed, and a control strategy is given. To validate the model, the dynamic model is integrated with the control system and compared with the traditional method to minimize the normal driving forces.
Complete Kinematics/Dynamics Modeling and Performance Analysis of a Novel SCARA Parallel Manipulator Based on Screw Theory

Dong Liang,Yi Mao,Yimin Song,Boyan Chang,Tao Sun

DOI: https://doi.org/10.1115/1.4064461

2024-02-05

Journal of Mechanisms and Robotics

Abstract:Abstract In this paper, a novel Selective Compliance Assembly Robot Arm (SCARA) high-speed parallel manipulator that can realize three-translation and one-rotation motion is proposed, and an accurate dynamic modeling methodology is investigated. The mechanism is composed of four limbs with a double parallelogram structure and a single moving platform. The high bearing capacity and high dynamic response of the novel mechanism make it a viable alternative choice for this kind of automation equipment. The degree-of-freedom (DOF) of the mechanism is analyzed by the screw theory. At the same time, the velocity mapping model of the mechanism is established by the twist screw and the actuated Jacobian matrix. Then, the acceleration mapping model of the mechanism, including the generalized kinematic pairs, is established by reduced acceleration state, the modified Lie screw, and the acceleration Hessian matrix. On this basis, the complete dynamic model with a compact form of the mechanism is deduced by the combination of screw theory and virtual work principle, and the correctness of the developed model is verified by multibody simulation software. Finally, considering the inertial characteristics of the mechanism, the dynamic performance distribution in the reachable workspace of the mechanism is analyzed by the Joint-Reflected Inertia (JRI) index and Coefficient of Variation of joint-space Inertia (CVI) index, and some areas are selected as the task workspace using the above index to guarantee good dynamic performance.

robotics,engineering, mechanical
Kinematic and Dynamic Analysis of a New Cylindrical 3-DOF Parallel Manipulator

Qi-Ming Wang,Jinsong Wang,Xin-Jin Liu,Hui Zhang

DOI: https://doi.org/10.1115/detc2002/mech-34304

2002-01-01

Abstract:This article discusses the kinematic and dynamic modeling of a new cylindrical parallel manipulator with two translational degrees of freedom and one rotational degree of freedom. The model of dynamics is based on the Lagrange approach. Six generalized coordinates and three Lagrange multipliers are introduced in the modeling process, and they are released by the corresponding constraint functions. A case is presented to illustrate the advantages of this mechanism. The simulation results indicate that the actuator torques of this parallel manipulator possess of good properties. This model will be useful to improve the design of the mechanical components and the control algorithm of this manipulator.
An Efficient Kinematic Calibration Method for Parallel Robots With Compact Multi-Degrees-of-Freedom Joint Models

Weijia Zhang,Zikang Shi,Xinxue Chai,Ye Ding

DOI: https://doi.org/10.1115/1.4064637

2024-02-28

Journal of Mechanisms and Robotics

Abstract:Abstract Forward kinematics-based modeling approaches are capable of constructing complete kinematic error models for parallel robots in a general way. The existing forward kinematics-based modeling methods replace multi-degrees-of-freedom (multi-DOF) joints with several 1DOF joints, allowing each limb of the parallel robot to be modeled like a serial robot. Nonetheless, this substitution complicates the kinematic model and results in additional computation. To overcome this limitation, an efficient kinematic calibration method adopting compact multi-DOF joint models is proposed. First, compact kinematic models for multi-DOF joints are established with the product of exponentials formula and adopted in the forward kinematic formulation of limbs. Error models of limbs are derived by simplifying the forward kinematic formulas' differentials, and the geometric error model for parallel robots is established by further concatenating and reformulating the limb error models. Next, the kinematic model is iteratively updated with the geometric parameter errors identified by the Levenberg–Marquardt algorithm. Error compensation is achieved through the inverse kinematics of the calibrated kinematic model. Finally, simulations and an experiment are implemented for validation. Compared with the existing forward kinematics-based modeling approaches, the error modeling procedures are simplified as the equivalent substitution of multi-DOF joints is avoided. The proposed approach also enhances the error compensation efficiency while maintaining high accuracy improvement.

robotics,engineering, mechanical
Kinematic and Dynamic Models of Hyper-Redundant Manipulator Based on Link Eigenvectors

Xiantong Xu,Haibo Xie,Cheng Wang,Huayong Yang

DOI: https://doi.org/10.1109/tmech.2023.3302853

2024-01-01

Abstract:Hyper-redundant manipulator has a slim geometric shape and super high degrees of freedom (DOF), which promises high motion efficiency and flexible obstacle avoidance ability in a confined space. Nevertheless, it also challenges the more complicated motion control strategy. In this article, the concepts of “link eigenvectors” and “manipulator's eigenpoints,” which apply to a widely used geometric kinematics method, are proposed. Hence, the kinematic and dynamic models can be constructed intuitively. And since the indirect joint space and local frames are replaced by the link eigenvectors and unified global frame, the kinematic and dynamic problems, especially the link's position, velocity, and acceleration, can be solved more directly. Further, based on the new models, mechanical analysis and Newton–Euler dynamic equations are effectively simplified, so as to realize the fast and precise dynamic resolution. Experiment results show that the kinematic and dynamic theoretical models are correct. And the driving forces of motors are successfully optimized, while the kinematic precision is improved simultaneously.
Simplified inverse dynamic models of parallel robots based on a Lagrangian approach

Zhou, Zhou

DOI: https://doi.org/10.1007/s11012-024-01782-6

IF: 2.7

2024-04-04

Meccanica

Abstract:This paper proposes and analyzes some simplified dynamic modeling methods for parallel robots. The proposed methods are based on a Lagrangian approach where the key concept consists in simplifying the expression of the energy for robots, especially for the distal links. First, the slender link method is discussed, where the link energy is calculated from the endpoints' velocities. Then, the commonly used equivalent point mass (EPM) method is analyzed. Since the EPM method uses point masses to replace links, the main problem is how to assign the values of point masses. According to the energy equivalence principle, some methods are proposed to solve the value-assigning problem. The derivations of the proposed methods are given, and the errors caused by each method are analyzed. Based on the error analyses, some simple approaches are introduced to improve the accuracy of the EPM methods. Inverse dynamic models of a spatial robot are established based on the proposed methods. Then, detailed comparisons and analyses of the different dynamic models are given to show that the proposed methods are simple and have relatively high accuracy.

mechanics
Dynamic Modeling and Performance Evaluation of a 5-DOF Hybrid Robot for Composite Material Machining

Xiaojian Wang,Jun Wu,Yulin Zhou

DOI: https://doi.org/10.3390/machines11060652

IF: 2.899

2023-01-01

Machines

Abstract:Dynamic performance is an important performance of robots used for machine processing. This paper studies the dynamic modeling and evaluation method of a 5-DOF (Degree of Freedom) hybrid robot used in aerospace composite material processing. With the consideration of the dynamics of the serial part, the complete dynamic model of the hybrid robot is established based on the virtual work principle. In addition to the widely considered acceleration term, a dynamic performance evaluation index that comprehensively considers the acceleration term, velocity term and gravity term in the dynamic model is proposed. Using the dynamic performance index, the effect of the placement direction of the robot and the arrangement of the double symmetric limbs on robot dynamics are investigated. The results indicate that the vertical placement is beneficial to the dynamics of the hybrid robot, and the arrangement of double symmetric limbs has different effects on different limbs.
Dynamic modeling and validation of a hybrid-driven continuum robot with antagonistic mechanisms

Jun Yang,Edward Harsono,Haoyong Yu

DOI: https://doi.org/10.1016/j.mechmachtheory.2024.105635

IF: 4.93

2024-04-11

Mechanism and Machine Theory

Abstract:To satisfy the actual needs of different tasks, hybrid-driven continuum robots need to effectively cope with rapid internal dynamic changes, relatively fast motion speeds, and enhanced flexibility in motions. This fact forces us to seek solutions from the perspective of the dynamics of continuum robots. However, the integration of multiple actuations introduces complexity to dynamic modeling. Therefore, this paper focuses on the dynamic modeling and validation of a hybrid-driven continuum robot with antagonistic mechanisms. Firstly, we construct a general kinematic model to transform local position and force vectors into the global coordinate frame. Then, we utilize Euler–Lagrange formalism to derive dynamical behaviors. Furthermore, an analytical stiffness model is incorporated into the dynamics to yield a full dynamic model (FDM). To facilitate efficient programming and calculation, the chain rule and properties of homogeneous coordinate transformation are employed to derive explicit expressions of each element within the constructed dynamic model. Additionally, a simplified dynamic model (SDM) by neglecting rotational kinetic energy involved in movements is provided to meet practical needs. Comparative experiments are conducted on a hybrid-driven continuum robot with two sections to demonstrate the effectiveness of these models.

engineering, mechanical
Dynamic Modeling of Spatial 6-DOF Parallel Robots Using Kane Method for Control Purposes

Chifu Yang,Qitao Huang,Zhengmao Ye,Junwei Han

DOI: https://doi.org/10.1109/IHMSC.2010.145

2010-01-01

Abstract:This paper readdressed the dynamics for spatial 6-DOF parallel robots (PR). With a view of improving the computational efficiency of dynamic equations and simplifying the modeling of PR, PR is regarded as seven rigid bodies, ignoring the complex dynamics of cylinder, and the dynamic equations are derived by using Kane method. The relationship of components of PR is described with geometric algorithms. SimMechanics is employed to build the full computer model of PR for verifying the dynamic equations. Simulation results show that the dynamic model of PR is accurate and effective, and it is more efficient for real time control.
Dynamic Modeling and Analysis of a Parallel Manipulator Using Simulink and SimMechanics

WANG Yingbo,HUANG Qitao,ZHENG Shutao,HAN Junwei,XU Hongguang

DOI: https://doi.org/10.3969/j.issn.1007-7043.201011057

2012-01-01

Abstract:In order to do a sufficient validation and analysis of the dynamic model of a 6-DOF parallel manipulator and improve the efficiency of the dynamic model and analysis,two computer-aided methods for dynamic modelling in a Simulink environment and SimMechanics environment were proposed.The 6-DOF parallel manipulator was described as a single rigid body using the Kane method to establish the single rigid body dynamic model along with the joint space control law to design a classic proportional-integral-derivative(PID) controller,and the simulation was carried out in Simulink and SimMechanics.The dynamic responses of the 6-DOF parallel manipulator in the two kinds of simulation environment are completely consistent,which proves that both of the two dynamic models using Simulink and SimMechanics are correct.Moreover,the proposed method can also be applied to all mechanical systems for dynamics modelling and analysis.
Inverse Dynamics and Simulation of a 3-DOF Spatial Parallel Manipulator.

YW Li,JS Wang,LP Wang,XJ Liu

DOI: https://doi.org/10.1109/robot.2003.1242226

2003-01-01

Abstract:Recently the parallel manipulators with less DOF have attracted the researchers, but works on their dynamics are relative few. In this paper, an inverse dynamic formulation is presented by the Newton-Euler approach for a spatial parallel manipulator, which has two translational degrees of freedom and one rotational degree of freedom. The inverse kinematics analysis is firstly performed in closed form. Then the force and moment equilibrium equations for the manipulator are presented. According to the kinematic constraints of the legs and the platform, some joint constraint forces are eliminated and an algorithm to solve the actuator forces is given. In addition, ADAMS is used to perform the kinematic and dynamic simulation for the manipulator. The simulation results are compared to those derived from algebraic formulae and the comparison shows the validity of the mathematical model.
A Novel Mechanical Model Based on the Dynamic Stiffness Matrix for Unified Dynamic and Static Modeling of Planar Compliant Mechanisms

Yunsong Du,Tianbao Pan,Chongxin Qiao,Tiemin Li

DOI: https://doi.org/10.1016/j.precisioneng.2024.10.003

2024-01-01

Abstract:This paper presents a dynamic and static modeling method for compliant mechanisms based on the dynamic stiffness matrix. Its advantage is that accurate dynamic and static modeling can be established simultaneously in frequency domain. Firstly, the dynamic stiffness matrices of flexure beams/hinges are introduced in detail. To ensure modeling accuracy, the nodes of flexible elements are translated to the research nodes, and the local coordinate system is rotated to make it consistent with the global coordinate system. The translation matrix and the rotation matrix are derived, and then the extended dynamic stiffness matrix of flexible elements is also obtained. Then the displacement of the discrete node and the displacement of the research node are taken as the hybrid state variables, and the dynamic model of the whole mechanism is established in frequency domain. The static model of the whole mechanism can be established by changing the angular frequency value. Eventually, two examples are given, and the proposed method is compared with other theoretical models and finite element analysis (FEA). The results show that this method has high modeling accuracy. It provides a reliable modeling method for dynamic and static performance analysis of compliant mechanisms.
Stiffness Modeling Approach for a 3-DOF Parallel Manipulator with Consideration of Nonlinear Joint Stiffness

Guang Yu,Liping Wang,Jun Wu,Dong Wang,Congjun Hu

DOI: https://doi.org/10.1016/j.mechmachtheory.2018.01.005

IF: 4.93

2018-01-01

Mechanism and Machine Theory

Abstract:Considering the nonlinear characteristics of joint, this paper proposes a new comprehensive stiffness analysis method by combining finite element analysis and matrix structural analysis. Based on the force/moment equilibrium equations of a 3-DOF over-constrained parallel manipulator, a method for solving the internal forces of the joints is proposed. By calculating the stiffness of the bearing under the action of joint internal forces, the stiffness matrix of the revolute joint and the composite spherical joint can be derived. The FEA-based identification method for the stiffness matrix of multi-node components is proposed by importing the structural model into the finite element software for virtual experiments. Then, integrating the stiffness matrices of components and joints, the stiffness matrix of the whole manipulator can be derived and the theoretical stiffness computed from the stiffness model is mapped in the workspace. Finally, the stiffness analysis method is verified by experiments in the physical prototype. (C) 2018 Elsevier Ltd. All rights reserved.

Dynamic Modeling For A High-Speed 3-Dof Parallel Robot With Compliant Joints

Dynamic Modeling and Analysis for Coupling Processing 6-DOF 3 P3 R Manipulator

Dynamic Modeling of Overconstrained Parallel Robot

Error Modeling of Parallel Robots for Semi-Physical Simulation Platform of Space Docking Mechanism

Dynamic Modeling of Flexible Parallel Robot

On The Method Of Linearizing Dynamic-Model And Solving Forward Dynamic Problems Of Flexible Robots

Dynamic Modeling and Simulation of a Hybrid Robot

Dynamic Modeling of a Parallel Manipulator with Two Translational Degrees of Freedom

Dynamic Model of a 3-DOF Redundantly Actuated Parallel Manipulator

Complete Kinematics/Dynamics Modeling and Performance Analysis of a Novel SCARA Parallel Manipulator Based on Screw Theory

Kinematic and Dynamic Analysis of a New Cylindrical 3-DOF Parallel Manipulator

An Efficient Kinematic Calibration Method for Parallel Robots With Compact Multi-Degrees-of-Freedom Joint Models

Kinematic and Dynamic Models of Hyper-Redundant Manipulator Based on Link Eigenvectors

Simplified inverse dynamic models of parallel robots based on a Lagrangian approach

Dynamic Modeling and Performance Evaluation of a 5-DOF Hybrid Robot for Composite Material Machining

Dynamic modeling and validation of a hybrid-driven continuum robot with antagonistic mechanisms

Dynamic Modeling of Spatial 6-DOF Parallel Robots Using Kane Method for Control Purposes

Dynamic Modeling and Analysis of a Parallel Manipulator Using Simulink and SimMechanics

Inverse Dynamics and Simulation of a 3-DOF Spatial Parallel Manipulator.

A Novel Mechanical Model Based on the Dynamic Stiffness Matrix for Unified Dynamic and Static Modeling of Planar Compliant Mechanisms

Stiffness Modeling Approach for a 3-DOF Parallel Manipulator with Consideration of Nonlinear Joint Stiffness