Phase Transformation In Ti2ni-Ni Systems

J Liu,Sh Ye,Xp Gao,Ht Yuan,Dy Song,Ys Zhang

2000-01-01

Abstract:In this work, we choose the chemical plating method to microencapsulate Ti2Ni alloy powders, the alloys were heated in the vacuum furnace at different conditions, and the phase and electrochemical characteristics of the alloys were measured.

What problem does this paper attempt to address?

Size Dependent Phase Transformation in Atomized TiAl Powders

Dong-Ye Yang,Shu Guo,Hua-Xin Peng,Fu-Yang Cao,Na Liu,Jian-Fei Sun

DOI: https://doi.org/10.1016/j.intermet.2015.02.017

IF: 4.075

2015-01-01

Intermetallics

Abstract:The paper focuses on the phase transformation of undercooled Ti-48Al (at.%) droplets atomized by high pressure gas. The microstructural evolution was analyzed using the transient nucleation theory in combination with the microstructural examinations. The primary phase, final phase volume fraction and the hardness are related to the droplets size to provide fundamental understanding. The competitive formation of the primary phases alpha and beta are strongly controlled by the droplets size, and a critical diameter of about 25 mu m was identified corresponding to an undercooling of 102 K. The final phase volume fraction of gamma increased with the increase of powder size from 12% to 85%. The highest hardness with the value of 652 HV was obtained for powder of 50 mu m in diameter. (C) 2015 Elsevier Ltd. All rights reserved.
Microstructure and phase transformation of TiNi alloy with addition of third element Sn

Yufeng Zheng,Fan Yang,Xianglong Meng,Wei Cai,LianCheng Zhao

2004-01-01

Rare Metal Materials and Engineering

Abstract:The microstructure and phase transformation behavior of Ti47.5Ni47.5Sn5 and Ti45Ni45Sn10 alloys have been studied by means of optical microscopy, electron probe X-ray micro-analysis, X-ray diffraction analysis, transmission electron microscopy and electrical resistance versus temperature curve measurement. The microstructure of as-cast Ti-Ni-Sn alloys consists of eutectic structure and TiNi matrix with 5at% Sn solid-soluted in the TiNi matrix of Ti47.5Ni47.5Sn5 alloy whereas 7 at% Sn solid-soluted in the TiNi matrix of Ti45Ni45Sn10 alloy. XRD results indicate that the crystal structure of the matrix in Ti47.5Ni47.5Sn5 and Ti45Ni45Sn10 alloys at room temperature is B-2 structure with the lattice parameter a(0)=0.302 9 nm and a(0)=0.303 2 nm, respectively. The eutectic structure consists of TiNi matrix and Ti5Sn3 phase, and the TiNi matrix in the eutectic structure has the similar composition to that of the primary TiNi matrix. A few Ni is found to be contained in Ti5Sn3 phase. TEM observations show that the eutectic structure in Ti-Ni-Sn alloys exhibit band-like and triangle-like morphologies. The Ti47.5Ni47.5Sn5 and Ti45Ni45Sn10 alloys would undergo martensitic transformation during cooling to -140 degreesC - 130 degreesC without precursory R phase transformation.
Phase Transformation Behavior of Porous NiTi Alloys Fabricated by Capsule-Free Hot Isostatic Pressing

S. L. Wu,X. M. Liu,Rk. Chu,C. Y. Chung,C. L. Chu,K. W. K. Yeung

DOI: https://doi.org/10.1016/j.jallcom.2006.01.144

IF: 6.2

2008-01-01

Journal of Alloys and Compounds

Abstract:Differential scanning calorimetry (DSC) was used to characterize the phase transformation of porous NiTi alloys. Results revealed that there existed a multi-stage martensitic transformation on cooling while either a single or two-stage transformation on heating. The DSC analysis indicated that the cold compaction pressure had great effect on the transformation temperatures. The transformation temperatures of NiTi with lower compaction pressure were higher than those of NiTi compacted at higher pressure. With increase in the annealing time, the transformation temperatures quickly increased for those alloys compacted at 150 MPa. However, there was only little change in the transformation temperatures for those compacted from 300 to 400 MPa. The change in the transformation temperature can be attributed to the combined effect of high dislocations density and precipitation of the second phase. (c) 2006 Elsevier B.V. All rights reserved.
The phase structures and electrochemical properties of TiV2.1Nix(x=0.2 similar to 0.6) hydrogen storage alloys

Fabang Bang Dai,Lixin Chen,Jian Liu,Fangping Zheng,Zhihong Zhang,Yongquan Lei,FF Dai,LX Chen,FP Zheng,YQ Lei

2005-01-01

Rare Metal Materials and Engineering

Abstract:The phase structures and electrochemical properties of TiV2.1Nix (x=0.2, 0.3, 0.4, 0.5, 0.6) hydrogen storage alloys have been investigated systematically. XRD and SEM show that all the alloys consist of a V-based solid solution main phase with b.c.c. structure and a TiNi-based secondary phase. The abundance and lattice parameters of main phase decrease with the increase of nickel content, while the abundance of TiNi-based secondary phase increases at the same time. The TiNi-based secondary phase forms a visible three-dimensional network along the grain boundaries of V-based solid solution main phase as x increases beyond 0.4. Electrochemical measurements show that the high-rate-dischargeability and cycling stability are noticeably improved as x increases. However, when x >= 0.4, the activation behavior and the maximum discharge capacity decline with the increase of nickel content. Among the studied alloys, the TiV2.1Ni0.4 has the best overall electrochemical performance.
Microstructure Evolution and Phase Transformation in a Nickel-Based Superalloy with Varying Ti/Al Ratios: Part 2 – Phase Transformation

Gang Liu,Lingbing Kong,Xueshan Xiao,Soran Birosca

DOI: https://doi.org/10.1016/j.msea.2021.142229

IF: 6.044

2021-01-01

Materials Science and Engineering A

Abstract:Nickel-based superalloy Waspaloy is one of the promising candidate materials for power plant components served in higher operation temperatures. Experimental alloys based on Waspaloy with varying Ti/Al ratios were produced and subjected to thermal exposure at 800 degrees C for up to 10,000 h. The phase transformations, mainly focusing on the i-Ni3Ti phase precipitation behavior and decomposition of two types of MC carbides during the prolonged ageing process, were investigated in this paper. i phases precipitated in the center of extra-large gamma' (EL-gamma '), with or without facilitated by the small size MC carbides that were embedded within EL-gamma' as well. There were different decomposition routes for MC carbides with different sizes. Most of the MC carbides with larger size followed the usual transformation to M23C6 carbides, whilst the decomposition of MC carbides with smaller size was related to the nucleation of i phase and/or other phases such as a phase in some cases. It is found that slightly lowering Ti/Al ratio (above 0.74) could not rule out the precipitation of i phase. The precipitation kinetics of i phase were discussed in terms of the density and stability of small size MC carbides. Furthermore, the effects of Ti/Al ratios on i formation were evaluated.
Insitu Study Of Phase-Transformations In A 50.8 At-Percent Ni-Ti Alloy

L Xuemin,Ty Hsu

DOI: https://doi.org/10.1016/0026-0800(87)90064-4

1987-01-01

Metallography

Abstract:Phase transformation behavior in a 50.8 at.% Ni-Ti alloy was studied by in situ transmission electron microscope observation. It was found that, upon cooling, the phase transformations B2 → Ic (probably) → R → B′19 occur successively, and only the B′19 → B2 transformation occurs upon heating. The substructure of martensite changes from twins to finer twins to stacking faults with increasing cooling rate. A probable explanation of the effect of cooling rate on the morphology of martensite is proposed. The orientation relationships between B2 and R phases, as well as martensite, were determined.
Phase Transformation and Interface Crystallography between TiO2 and Different TinO2n-1 Phases

Xiaodong Wu,Na Yang,Yuanxiao Ji,Xuexia He,Qi Li,Ruibin Jiang,Zhibin Lei,Zonghuai Liu,Jie Sun

DOI: https://doi.org/10.1039/d2ce01410f

IF: 3.756

2023-01-12

CrystEngComm

Abstract:Magnéli phase titanium oxide (TinO2n-1, 4≤n≤10) has wide application prospects in energy storage, catalysis and other fields. During the preparation of TinO2n-1 phase from TiO2 by carbothermal reduction reaction (CRR), the coexistence of multiple phases caused by the change in the reduction degree is the theoretical and practical basis for obtaining TiO2/TinO2n-1 composite materials. In this work, H2Ti3O7 nanofiber has been employed as precursor for the following CRR process. The X-ray diffraction (XRD), Raman spectroscopy and Thermogravimetric (TG) and Differential Scanning Calorimetry (DSC) analysis results confirmed the phase transformation process of H2Ti3O7→TiO2 (B)→Anatase→Rutile→TinO2n-1. Comprehensive transmission electron microscope (TEM) characterization was carried out to investigate the phase composition and interface structures of the products calcinated under different temperatures. TiO2/Ti5O9 and λ-Ti3O5/γ-Ti3O5 interfaces have been observed with specific orientation relationships. In addition, the phase transition mechanism has also been revealed based on the structural analysis results. By carefully considering the crystal structure and symmetry of the parent and new phase, the initial lattice strain matrix based on the two observed interfaces has been established accordingly. The crystallographic features of the two types of interfaces have been calculated based on modified invariant line theory, which has confirmed the consistency of the experimental observation and calculated results. The research in this paper can further expand the applicability of the three-dimensional invariant line theory in low symmetry crystal materials.

chemistry, multidisciplinary,crystallography
Phase Transformation Behavior of A Tinicu Shape Memory Alloy Electrolytically Charged with Hydrogen

JH Wu,XT Zu,ZG Wang,YZ Liu

IF: 6.318

2005-01-01

Rare Metals

Abstract:The transformation behavior of a TiNiCu shape memory alloy electrolytically charged with hydrogen was investigated by means of different scanning calorimetry (DSC), optical microscope and X-ray diffraction (XRD). The results showed that inter- and inner-granular hydrides formed after charging with hydrogen, and the hydrides suppressed martensitic transformation. The electrolytically charged hydrogen can be easily released by heat treatment and the transformation occurred again, which was verified by the DSC and XRD experiments.
Investigation of the Phase Transformations in Ti 22al 25nb Alloy

Bin Shao,Yingying Zong,Daosheng Wen,Yingtao Tian,Debin Shan

DOI: https://doi.org/10.1016/j.matchar.2016.02.011

IF: 4.537

2016-01-01

Materials Characterization

Abstract:In this paper, changes in the morphology and composition of the O, α2 and B2/β phases and the transformation relationship between the three phases of Ti22Al25Nb alloy were systematically investigated by performing a series of short heat treatments. The results showed that the phase transformations can be divided into three stages in the temperature range of 870°C~1080°C. In the first stage of 870°C~930°C, the O phase started transferring to α2+B2 first along grain boundaries with lamellar morphology due to short-range diffusion, and the O→α2+B2 reaction was accompanied by a large amount of Nb segregation. With the increase in temperature, the phase transformation migrated from the boundaries to the inside of the grains, and the α2-phase spheroidized gradually. In the second stage from 960°C to 1020°C, granular α2 and B2 phases precipitated directly from the O phase due to long-range diffusion. At 1020°C, the O→α2+B2 transition was completed and the granular α2 phase mainly populated along the grain boundaries. In the third stage above 1020°C, the main phase transformation was α2→B2, and the aggregation and growth of the α2 phase were observed in α2-rich regions.
Phase Transformation Behavior of TiNi Based Shape Memory Alloy Films

Zhi-guo WANG,Xiao-tao ZU,Xiang-dong FENG,Hua-jun YU,Yong-qing FU

DOI: https://doi.org/10.3969/j.issn.1005-5053.2006.04.014

2006-01-01

Abstract:In this work,TiNi and TiNiCu shape memory alloy films on Si and SiO_2 substrate were successfully prepared by co-sputtering of TiNi target with a separated Cu and Ti target.The transformation behavior and stress as a function of temperature were investigated by differential scanning calorimeter(DSC) and curvature measurement methods.The results showed that the shape memory alloy film has a good shape memory effect,which was a promising candidate material for micro-electric mechanical system.For TiNi shape memory alloy film,two-stage transformation was observed,corresponding to transformations among austensite,R-phase and martensite phase.However,austensite transforms into martensite directly for TiNiCu film.The substrate and the composition of the film had a prominent effect on the transformation temperatures.The film had a good adherence on the Si substrate and is easy peeled from the SiO_2 substrate.
Phase Transformation Behaviors of TiNi Fibers Embedded in an Aluminum Matrix

Jie Hu,Qiang Zhang,Yan Liu,Gaohui Wu

DOI: https://doi.org/10.1016/j.jallcom.2013.12.048

IF: 6.2

2013-01-01

Journal of Alloys and Compounds

Abstract:The effect of tensile deformation on the phase transformation behaviors of TiNi fibers which were embedded in a pure aluminum matrix was discussed in this paper. Differential scanning calorimeter (DSC) was used to study the martensite transformation. The microstructures of the TiNi fiber before and after tensile deformation were observed by transmission electron microscopy (TEM). Results show that martensite induced by stress preferentially nucleated at the grain boundary and the dislocation. When the amount of tensile deformation was higher than 4%, a two-stage transformation behavior was observed in the heating process. The peak appeared at low temperature correspond to the martensite induced by stress. While the peak appeared at high temperature correspond to preferentially oriented martensite. However, the martensite fraction remaining in the fibers increased with the prestrain level increasing because part of the martensite was deformed into fully detwinned preferentially oriented martensite, which cannot be detected by DSC. (C) 2013 Elsevier B.V. All rights reserved.
The study of constitutional phases in a Ni47Ti44Nb9 shape memory alloy

C.S. Zhang,Y.Q. Wang,W. Chai,L.C. Zhao

DOI: https://doi.org/10.1016/0254-0584(91)90051-U

IF: 4.778

1991-01-01

Materials Chemistry and Physics

Abstract:The constitutional phases and microstructure of Ni47Ti44Nb9 alloy have been studied by means of optical microscopy, electron probe X-ray microanalyses (EPMA) and X-ray diffraction. It has been shown that the microstructure of the experimental alloy consists of three phases:TiNi matrix, niobium-rich phase and Ti3(Ni,Nb)2 compound. The Nb-rich phase is determined to be β -Nb with bcc structure containing a small amount of Ni and Ti. The β -Nb is a soft phase which forms a eutectic structure with TiNi phase during solidification. After hot working the soft β -Nb phase is dispersed in TiNi matrix and gives rise to a wide transformation hysteresis in the alloy. The Ti3(Ni,Nb)2 is a harder and embrittlemental phase.
Microstructures and Transformation Characteristics of Thin Films of Tinicu Shape Memory Alloy

XL Cheng,D Xu,BC Cai,L Wang,J Chen,G Li,S Xu

IF: 3.752

2002-01-01

Transactions of Nonferrous Metals Society of China

Abstract:Both sputtering conditions and crystallizing temperatures have great influence on the microstructures and phase transformation characteristics for Ti51Ni44Cu5.By means of the resistance-temperature measurement,X-ray diffraction and atomic fore microscopic study,the results indicate that the transformation temperatures of the thin films increase and the "rock candy" martensitic relief is more easily obtained with promoting the sputtering Ar pressure,sputtering power,or crystallizing temperature.However,when sputtering Ar pressure,sputtering power,or crystallizing temperature are lower,a kind of "chrysanthemum" relief,which is related with Ti-rich GP zones,is much easier to be observed.The reason is that during crystallization process,both of the inherent compressive stresses introduced under the condition of higher sputtering pressure or higher crystallizing temperature are helpful to the transition from GP zones to Ti2(NiCu) precipitates and the increase of the transformation temperatures.The addition of copper to substitute for 5% nickel in mole fraction can reduce the transformation hysteresis width to about 10～15 ℃.
In-situ phase transformation and corrosion behavior of TiNi via LPBF

Gang Chen,Shuying Liu,Chao Huang,Yuan Ma,Ying Li,Baicheng Zhang,Lei Gao,Bowei Zhang,Pei Wang,Xuanhui Qu

DOI: https://doi.org/10.1016/j.corsci.2022.110348

IF: 7.72

2022-04-01

Corrosion Science

Abstract:As well known, shape memory effect of TiNi alloy is driven by phase transition under stress or temperature variation. Corrosion behavior of the TiNi component particularly that produced by additive manufacturing associated with phase transition is still a blind point. In this work, the control of B2/B19′ phase composition in the NiTi component is realized via LPBF. Subsequently, electrochemical testing was carried out to evaluate the corrosion resistance of NiTi alloys. The results show that the as-printed sample exhibits a better corrosion resistance than the ingot sample. Furthermore, the as-printed sample with full B2 phase yields a much stronger pitting corrosion resistance than that with a mixed B2/B19′ phase. Based on the first principle calculations, it is found that the stability of passive film on B19′ phase is slightly weaker than that on B2 phase. Moreover, Tof-SIM analysis revealed that the passive film obtained from component surface with mixed B2/B19′ phase is irregular, where pitting corrosion tended to initiate. This work is believed to serve as a reference for the process optimization of additive manufacturing NiTi shape memory alloys.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Phase Transformation of Niti Shape Memory Alloy Powders Prepared by Ball Milling

B. Tian,Y. X. Tong,F. Chen,Y. Liu,Y. F. Zheng

DOI: https://doi.org/10.1016/j.jallcom.2008.10.079

IF: 6.2

2009-01-01

Journal of Alloys and Compounds

Abstract:Ni50.8Ti49.2 alloy powders of different particle shapes and sizes have been prepared by ball milling. The powder milled for 1h has large flaky particles and are partially amorphous. The powder crystallized through a single-stage exothermic transformation upon heating. Powders milled for longer durations consisted of partially amorphous Ni–Ti, [Fe,Ni] and Ni–Cr–Fe phases, indicating heavy contamination from the milling vessel. Upon heating, the milled powders exhibited an endothermic event at ∼400°C. After annealing at 500°C, the milled powders were fully crystallized. The crystallized powders exhibited martensitic transformation with reduced heat effect. The critical temperatures of the transformation were found to decrease with increasing ball milling time.
Phase Transformation, Microstructural Evolution and Tensile Properties of a TiH2-Based Powder Metallurgy Pure Titanium

Hairui Zhang,Cong Wang,Junqing Guo,Wuhui Li,Chu Cheng,Nan Xiang,Tao Huang,Hongzhi Niu,Deliang Zhang,Fuxiao Chen

DOI: https://doi.org/10.3390/met14111218

IF: 2.695

2024-10-26

Metals

Abstract:Multiple phase transformations were carried out during dehydrogenation process of TiH2-based powder metallurgy. The influence of phase transformation on the microstructure is highly worthy of attention. In situ synchrotron radiation was employed to investigate the phase transformation sequence of TiH2 powder compact during the vacuum sintering process. It was found that a transformation route TiH1.971 → TiH2 + TiH + TiH0.71 + α(H) → TiH + TiH0.71 + α(H) → TiH + TiH0.71 + α(H) + β(H) → α(H) → α took place, resulting in an equiaxed microstructure. Increasing heating rate and avoiding the intense dehydrogenation to retain hydrogen-rich β (β(H)) and TiHx aciculae at the interfaces is found to be a feasible method to fabricate hierarchical α-Ti structures. A fully dense fine martensitic microstructure was produced after fast heating the TiH2 powder compact to 1100 °C and an immediate hot extrusion. Subsequently, by vacuum annealing treatment at 700 °C, composite α/βt lamellar structures were generated and a simultaneously enhanced tensile strength of 746 MPa and excellent elongation to fracture of 33.8% were achieved. It is suggested that adjusting the dehydrogenation reactions of TiH2-based powder metallurgy is conductive to generating hierarchical lamellar structures with a highly promising combination of strength and ductility for pure Ti.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Phase Transformation of Tini Shape Memory Alloy under Electron Irradiation

FR Wan,XT Zu,LM Wang

DOI: https://doi.org/10.1142/9789812705198_0031

2003-01-01

Abstract:The irradiation effect of TiNi shape memory alloy was studied by transmission electron microscope. It is found that intermediate rhombohedral phase (R phase) in the alloy would disappear under electron irradiation at accelerate voltage of above 320 W. The relation between electron irradiation and the stability of R phase was discussed.
Study on phase transformation behavior and mechanical properties of equiatomic ratio NiTi alloy formed by selective laser melting

Changhui Song,Junfei Huang,Linqing Liu,Zehua Hu,Yongqiang Yang,Di Wang,Chao Yang

DOI: https://doi.org/10.1108/rpj-05-2021-0114

2022-12-28

Rapid Prototyping Journal

Abstract:Purpose This paper aims to better control the mechanical properties and functional properties of NiTi alloy. Design/methodology/approach NiTi alloy samples with equal atomic ratio were formed by selective laser melting (SLM). X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy and tensile testing methods were used to study the effects of different laser power and scanning speed on the densification behavior, phase transformation characteristics and mechanical properties of NiTi alloy. Findings Compared with the laser power, the variation of the keyhole effect caused by the change of scanning speed is more intense, which has a greater effect on the densification behavior of SLM NiTi alloy. The effect of the laser power on the phase transition temperature is small. The increase of scanning speed weakens the burning degree of Ni element, so phase transition temperature decreases. The results of DSC test and tensile test show that the scanning velocity can significantly change the phase transition temperature, martensite twins reorientation and stress–strain behavior of SLM NiTi alloy. Originality/value This study provides a potential method to regulate the mechanical properties and functional properties of NiTi shape memory alloy in the future and NiTi alloys formed by SLM with good elongation were obtained because the Supercellular crystal structure formed during the nonequilibrium solidification of SLM and the superfine precipitates dispersed in the alloy prevented the dislocation formation.

engineering, mechanical,materials science, multidisciplinary
Formation of lamellar microstructure in Ti-48Al-7Nb-2.5V-1Cr alloy

Yonghao Yu,Hongchao Kou,William Yi Wang,Yichao Wang,Fengming Qiang,Chengxiong Zou,Jinshan Li

DOI: https://doi.org/10.1016/j.matdes.2022.111342

2022-11-05

Abstract:The reasonable design and application of phase transformation is an efficient approach to coordinate the microstructure and properties of alloys. The sequence of compositional and structural transformation determines the type and mechanism of phase transformation. Because of their low density and excellent high-temperature properties, TiAl alloys that contain fully lamellar microstructure have been applied to low-pressure turbine engine blades. However, there is no consensus on the mechanism of lamellar formation. Here, we propose a new mechanism that is dominated by spinodal decomposition, in which compositional transformation occurs prior to structural transformation during lamellar formation. Transitional lamellae with fcc-based long-period superstructures are introduced to prove the mechanism of sequentially spinodal decomposition, shear transformation, compositional modulation and ordering.

materials science, multidisciplinary
Crystallization Kinetics and Martensitic Transformation of Ti49Ni46.5Ce4.5 Alloy Thin Film

Y. C. Lei,H. J. Zhao,W. Cai,L. X. Gao,X. An

DOI: https://doi.org/10.1016/j.vacuum.2010.01.048

IF: 4

2010-01-01

Vacuum

Abstract:The Ti49Ni46.5Ce4.5 alloy thin film was prepared by direct current (DC) magnetron sputtering system for the first time. Crystallization kinetics, phase composition and the behaviors of martensitic transformation were studied. The results by X-ray diffraction (XRD) and differential scanning calorimeter (DSC) demonstrated that the primary second phase of TiNiCe alloy thin films was Ce2Ni7 phase, apparent activation energy was determined to be 510 kJ/mol at the continuous heating process, Avrami exponents for different isothermal temperature were in the range of 1.1-1.88 between 713 and 730 K, one-step martensitic transformation was observed in the crystallized Ti49Ni46.5Ce4.5 alloy thin films. The influence of thermal process on martensitic transformation temperature was investigated with non-isothermal and isothermal crystallization. The reason behind the transformation temperature change was also discussed. (C) 2010 Elsevier Ltd. All rights reserved.

Phase Transformation In Ti2ni-Ni Systems

Size Dependent Phase Transformation in Atomized TiAl Powders

Microstructure and phase transformation of TiNi alloy with addition of third element Sn

Phase Transformation Behavior of Porous NiTi Alloys Fabricated by Capsule-Free Hot Isostatic Pressing

The phase structures and electrochemical properties of TiV2.1Nix(x=0.2 similar to 0.6) hydrogen storage alloys

Microstructure Evolution and Phase Transformation in a Nickel-Based Superalloy with Varying Ti/Al Ratios: Part 2 – Phase Transformation

Insitu Study Of Phase-Transformations In A 50.8 At-Percent Ni-Ti Alloy

Phase Transformation and Interface Crystallography between TiO2 and Different TinO2n-1 Phases

Phase Transformation Behavior of A Tinicu Shape Memory Alloy Electrolytically Charged with Hydrogen

Investigation of the Phase Transformations in Ti 22al 25nb Alloy

Phase Transformation Behavior of TiNi Based Shape Memory Alloy Films

Phase Transformation Behaviors of TiNi Fibers Embedded in an Aluminum Matrix

The study of constitutional phases in a Ni47Ti44Nb9 shape memory alloy

Microstructures and Transformation Characteristics of Thin Films of Tinicu Shape Memory Alloy

In-situ phase transformation and corrosion behavior of TiNi via LPBF

Phase Transformation of Niti Shape Memory Alloy Powders Prepared by Ball Milling

Phase Transformation, Microstructural Evolution and Tensile Properties of a TiH2-Based Powder Metallurgy Pure Titanium

Phase Transformation of Tini Shape Memory Alloy under Electron Irradiation

Study on phase transformation behavior and mechanical properties of equiatomic ratio NiTi alloy formed by selective laser melting

Formation of lamellar microstructure in Ti-48Al-7Nb-2.5V-1Cr alloy

Crystallization Kinetics and Martensitic Transformation of Ti49Ni46.5Ce4.5 Alloy Thin Film