Abstract:As significant fluid machinery, canned motor pumps are widely applied in industrial field. The typical characteristic of canned motor pump is that the fluid comes into the narrow gap and affects the performance of canned motor. The coolant flow in the narrow annular gap between rotor and stator cans belongs to Taylor-Couette-Poiseuille flow which has been investigated for a long time while the thermal design is a key function of internal narrow gap annular flow of canned motor. However, the temperature distribution prediction of canned motor deviates from the experiments, especially in the high-capacity canned motor due to the large shear rate of fluid and eddy-current loss of motor's can. According to the researcher's work, the significant work lies in the heat transfer coefficient that different researchers give various numerical prediction and experimental measurement. It brings big challenge in thermal design of high capacity canned motor pump. In this paper, the author focuses on the reason why the heat transfer coefficient is remarkably lower than that other's forecast. In this paper, the heat transfer behavior of the boundary layer near surfaces in the annular flow is investigated by using the commercial fluid dynamic (CFD) method. Firstly, the Naiver-Stocks (N-S) equations and energy conservation equation are employed for modeling the flow and heat transfer behavior, and the k-omega turbulent model is used for solving the flow control equations. Secondly, the fluid domain is described by a simplified geometrical model: two concentric cylinders with finite gap length. Thirdly, numerical approach is used to analyze the subject with tools of Solidworks, ICEM CFD and Ansys Fluent. Two parameters are analyzed in the research, namely the rotating speed and the wall heat flux, without considering the fluid viscous dissipation and thermal contact resistance. Numerical simulation results indicate that Taylor vortex exists in the flow regime, and the temperature distribution is affected by both the rotating speed and the wall heat flux, named thermal barrier effect under large heat flux condition. The thermal barrier effect lies in that the temperature gradient of interface decreases compared to the peak value of temperature gradient near the surface, so that the heat transfer coefficient is reduced remarkably. This effect leads to the temperature prediction deviates from the experiment measurement.

Cfd Analysis Of The Hydrodynamic Characteristics Of An Eccentric Shaft In A Canned Motor

Heat Transfer Behavior Of The Boundary Layer Near Surfaces In Annular Flow Of High Capacity Canned Motor Pump

Quantitative Analysis of Energy Loss and Vibration Performance in a Circulating Axial Pump

Evaluation of shaft forces in a vertical canned motor through local hydraulic loss analysis

Numerical Simulation and Analysis on Hydraulic Performance in Vertical Canned Motor Pump

Numerical Simulation of Turbulent Taylor-Couette Flow with High Taylor Number and Large Radius Ratio in High-Speed Canned Motor Pump Internals

Effect of Suction and Discharge Conditions on the Unsteady Flow Phenomena of Axial-Flow Reactor Coolant Pump

A FLUID-THERMAL ANALYSIS OF PARTIAL ADMISSION AXIAL TURBINES

Study on Turbulent Taylor-Couette Flow with High Reynolds Number and Large Radius Ratio in High-Speed Canned Motor Pump Internals

Dynamic analysis of the pump system based on MOC–CFD coupled method

Research on the flywheel clearance flow and heat transfer characteristics in a horizontal canned motor reactor coolant pump

Mechanism analysis of the abnormal head-cover vibration of an ultra-high-head pump-turbine operating in pump mode by CFD and FEM

Cfd Numerical Simulation of the Complex Turbulent Flow Field in an Axial-Flow Water Pump

Thermal–hydraulic Calculation and Analysis of a 600 MW Supercritical Circulating Fluidized Bed Boiler with Annular Furnace

A Thermohydrodynamic Analysis of the Self-Lubricating Bearings Applied in Gear Pumps Using Computational Fluid Dynamics Method

CFD-Rotordynamics Sequential Coupling Simulation Approach for the Flow-Induced Vibration of Rotor System in Centrifugal Pump

Numerical Predictions and Stability Analysis of Cavitating Draft Tube Vortices at High Head in a Model Francis Turbine

Numerical Analysis on the Hydraulic Performance of the Auxiliary Impeller in Large Capacity Canned-Motor Pump

Preliminary Applications of CFD Methodology on Analysis of the Single-Phase Laminar Natural Circulation under Swing Conditions

Numerical Research on Dynamic Lateral Vibration of a Pump Turbine’s Shaft System

Dynamic Analysis and Modeling of Large-scale Canned Motor Pump Rotor Based on ANSYS