Abstract:Welding deformation prediction can predict the deformation that may occur during the welding process, so that corresponding measures can be taken to control the deformation, so as to improve the manufacturing quality and driving safety of the car body. In this paper, the finite element analysis software is used to simulate the welding process of the load wheel flange plate of the special vehicle body. The load wheel flange plate is one of the main components connecting the load wheel and the body, which can reduce the impact caused by uneven ground or high speed driving, so as to protect the load wheel, axle and body system. In this paper, the finite element analysis model of the load wheel flange is established. Based on the finite element analysis method, the welding deformation data set under different welding voltage, welding current and welding speed is obtained. In this paper, the process parameters of orthogonal experimental design are used for welding, and the deformation of the flange plate of the load wheel after welding is measured by three-dimensional laser scanner. The simulation results of welding deformation are in good agreement with the experimental results, and the relative error is controlled within 9.4%. Therefore, the finite element simulation method in this paper can better reflect the actual welding deformation. In order to improve the efficiency and accuracy of welding deformation prediction, a deformation prediction model based on improved genetic algorithm optimized BP neural network(improved GA-BP)is proposed. The average absolute error MAE and the determination coefficient R 2 are used as test parameters to evaluate the accuracy of the established model. The results show that compared with the unimproved BP neural network, the GA-BP model has a 0.04% increase in R 2 and a 13.04% decrease in MAE in the performance of the test set, which has a high reference value for the subsequent improvement of welding quality. Finally, the improved GA-BP algorithm model is used to verify the engineering verification of the flange plate of the load wheel obtained by the welding experiment. Based on the improved GA-BP neural network, the error between the predicted value of the welding deformation and the average value of the experimental measurement is within 10%, and the predicted value is consistent with the experimental measurement value. The application value of the improved GA-BP neural network in engineering is verified.

Deformation Prediction of Thin-Walled Parts Based on BP Neural Network

Deformation Forecast in Numerical Control Milling Based on Artificial Neural Networks

Prediction and Compensation of Force-Induced Deformation for a Dual-Machine-based Riveting System Using FEM and Neural Network

Prediction of Shot Peen Forming Parameters of Integral Aircraft Wing Panels

Milling Deformation Prediction for Thin-Walled Components Based on Fusion Model

PREDICTION OF THE BEARING CAPACITY OF THIN-WALLED BOX WITH GEOMETRIC IMPERFECTION USING BP NEURAL NETWORK

Modeling and Predicting of Aeronautical Thin-Walled Sheet Metal Parts Riveting Deformation

Optimization of 3D Printing Parameters on Deformation by BP Neural Network Algorithm

An ATPSO-BP Neural Network Modeling and Its Application in Mechanical Property Prediction

CNN-GRU Network-based Force Prediction Approach for Variable Working Condition Milling Clamping Points of Deformable Parts

Prediction of NC tube bending process parameters based on artificial neural network

Research on Prediction of Welding Deformation Based on Improved GA-BP Neural Network

Prediction of Facial Deformation after Complete Denture Prosthesis Using BP Neural Network

A Data-Driven Method for Predicting Deformation of Machined Parts Using Sparse Monitored Deformation Data

Optimization and prediction of volume shrinkage and warpage of injection-molded thin-walled parts based on neural network

Surface Topography Prediction Model in Milling of Thin-Walled Parts Considering Machining Deformation

Bending deformation prediction in a welded square thin-walled aluminum alloy tube structure using an artificial neural network

Deformation Prediction in Flank Milling of Thin-Walled Parts Based on Cutter-Workpiece Engagement

Adaptive Optimization Method for Prediction and Compensation of Thin-Walled Parts Machining Deformation Based on On-Machine Measurement

Prediction of the Deformation of Aluminum Alloy Drill Pipes in Thermal Assembly Based on a BP Neural Network

Prediction Model for Machining Deformation of Aeronautical Aluminum Alloy Thin-Walled Workpiece