Abstract:Background: Accurate and portable respiratory parameter measurements are critical for properly managing chronic obstructive pulmonary diseases (COPDs) such as asthma or sleep apnea, as well as controlling ventilation for patients in intensive care units, during surgical procedures, or when using a positive airway pressure device for sleep apnea. Objective: The purpose of this research is to develop a new nonprescription portable measurement device that utilizes relative humidity sensors (RHS) to accurately measure key respiratory parameters at a cost that is approximately 10 times less than the industry standard. Methods: We present the development, implementation, and assessment of a wearable respiratory measurement device using the commercial Bosch BME280 RHS. In the initial stage, the RHS was connected to the pneumotach (PNT) gold standard device via its external connector to gather breathing metrics. Data collection was facilitated using the Arduino platform with a Bluetooth Low Energy connection, and all measurements were taken in real time without any additional data processing. The device's efficacy was tested with 7 participants (5 men and 2 women), all in good health. In the subsequent phase, we specifically focused on comparing breathing cycle and respiratory rate measurements and determining the tidal volume by calculating the region between inhalation and exhalation peaks. Each participant's data were recorded over a span of 15 minutes. After the experiment, detailed statistical analysis was conducted using ANOVA and Bland-Altman to examine the accuracy and efficiency of our wearable device compared with the traditional methods. Results: The perfused air measured with the respiratory monitor enables clinicians to evaluate the absolute value of the tidal volume during ventilation of a patient. In contrast, directly connecting our RHS device to the surgical mask facilitates continuous lung volume monitoring. The results of the 1-way ANOVA showed high P values of .68 for respiratory volume and .89 for respiratory rate, which indicate that the group averages with the PNT standard are equivalent to those with our RHS platform, within the error margins of a typical instrument. Furthermore, analysis utilizing the Bland-Altman statistical method revealed a small bias of 0.03 with limits of agreement (LoAs) of -0.25 and 0.33. The RR bias was 0.018, and the LoAs were -1.89 and 1.89. Conclusions: Based on the encouraging results, we conclude that our proposed design can be a viable, low-cost wearable medical device for pulmonary parametric measurement to prevent and predict the progression of pulmonary diseases. We believe that this will encourage the research community to investigate the application of RHS for monitoring the pulmonary health of individuals.

A flow interruption device for measurement of airway resistance.

Correlative Research of Airway Resistance with Interrupter Technique and Routine Pulmonary Function

Differentiating Between Adductor and Abductor Spasmodic Dysphonia Using Airflow Interruption

Assessing the effectiveness of inhalation therapy in patients with chronic airway diseases: A new digital measurement

Measuring the mechanical input impedance of the respiratory system with breath-driven flow oscillations

Noninvasive determination of upper airway resistance and flow limitation

Continuous Critical Respiratory Parameter Measurements Using a Single Low-Cost Relative Humidity Sensor: Evaluation Study

Air sampling from PAP devices: Gone with the wind?

Direct measurement of intratracheal pressure in pediatric respiratory monitoring

Flowrate Sensing and Measurement in Portable Smart Inhalers

Feasibility Study: A stand alone, 3D printed respiratory oscillometer powered by Raspberry Pi suitable to detect airway obstruction in COPD.

[Analysis of flow-volume curves in asthmatic patients and their application in pharmacodynamic tests (author's transl)]

Comparison of Forced and Impulse Oscillometry Measurements: A Clinical Population and Printed Airway Model Study

Particle flow rate from the airways as fingerprint diagnostics in mechanical ventilation in the intensive care unit: a randomised controlled study

A Physical Analog to Assess Surgical Face Mask Air Flow Resistance During Tidal Ventilation

Receiver operating characteristic analysis of aerodynamic parameters obtained by airflow interruption: a preliminary report.

[Research on portable airway impedance monitoring device based on expiratory oscillation]

A Method for Monitoring the Effective Air Change Rate for Respiratory Aerosols Using Real-Time Tracers

Estimation of inspiratory effort using airway occlusion maneuvers in ventilated children: a secondary analysis of an ongoing randomized trial testing a lung and diaphragm protective ventilation strategy

Tidal changes in respiratory resistance are sensitive indicators of airway obstruction in children

Measuring Intraoral Pressure: Adaptation of a Dental Appliance Allows Measurement During Function