Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Employing Synergetic Effect of ZnSe Quantum Dots and Layered Ni(OH)2 to Boost the Performance of Lithium–sulfur Cathodes

A Nitrogen/Oxygen Dual-Doped Porous Carbon with High Catalytic Conversion Ability Toward Polysulfides for Advanced Lithium–Sulfur Batteries

Bimetallic Nanoparticles Decorated Porous Carbon As the Host Material to Enhance the Performance of Lithium-Sulfur Batteries

Incorporation ZnS quantum dots into carbon nanotubes for high-performance lithium-sulfur batteries

A Synergistic Strategy with 3D Highly Conductive Carbon Matrix‐Decorated with Low Loading of CdS Quantum Dots as a Sulfur Host for Advanced Li−S Batteries

MoS2 Quantum Dots-Decorated CNTs Networks as Sulfur Host Enhanced Electrochemical Kinetics for Advanced Lithium–Sulfur Batteries

Efficient Co 0.85 Se-CNT sulfur cathode derived from strong catalyst-support interactions: Contribution of adsorption-catalysis mechanism to the redox kinetics of polysulfides

Fully Integrated Hierarchical Double-Shelled Co9S8@CNT Nanostructures with Unprecedented Performance for Li-S Batteries

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

Design of ZnSe-CoSe heterostructure decorated in hollow N-doped carbon nanocage with generous adsorption and catalysis sites for the reversibly fast kinetics of polysulfide conversion

Core–shell zeolite imidazole framework-derived ZnSe@CoSe2/C heterostructure enabling robust polysulfide adsorption and rapid Li+ diffusion in high-rate and high-loading lithium–sulfur batteries

Coordinated Immobilization and Rapid Conversion of Polysulfide Enabled by a Hollow Metal Oxide/Sulfide/Nitrogen‐Doped Carbon Heterostructure for Long‐Cycle‐Life Lithium‐Sulfur Batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

MOF-Derived Bifunctional Co 0.85 Se Nanoparticles Embedded in N-Doped Carbon Nanosheet Arrays as Efficient Sulfur Hosts for Lithium–Sulfur Batteries

Implanting Single Zn Atoms Coupled with Metallic Co Nanoparticles into Porous Carbon Nanosheets Grafted with Carbon Nanotubes for High‐Performance Lithium‐Sulfur Batteries

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Regulating the P-band center of SnS 2 -SnO 2 heterostructure to boost the redox kinetics for high-performance lithium-sulfur battery

Nitrogen Doped Carbon Nanosheets Encapsulated in Situ Generated Sulfur Enable High Capacity and Superior Rate Cathode for Li-S Batteries

Synergistic improvements on capacity and Coulombic efficiency of lithium-sulfur batteries with NiSe-Ni 2 P/C modification on PP separators

Hierarchically structured catalytic and adsorptive ZnS-modified carbon microtubule interlayers for lithium‐sulfur batteries

An Entangled Cobalt–Nitrogen–Carbon Nanotube Array Electrode with Synergetic Confinement and Electrocatalysis of Polysulfides for Stable Li–S Batteries