Abstract:Herein, the cryogenically martensitic transformation and its effects on the tempering behaviors of bearing steel was investigated. An in-situ magnetic method was used for obtaining the thermodynamics of the martensitic transformation at sub-zero Celsius temperature from in respects of athermal and isothermal conditions. Microstructure evolution was also characterized systematically to investigate the mechanisms of the martensitic transformation. The results showed that the athermally martensitic transformation of samples experienced three different stages, where the martensite formed slowly at 300–230 K, rapidly at 230–120 K, and slowly again at 120–77 K during the continuous cooling process. With the increase of cooling rate, both the start and finish temperatures of the transformation rise, while the maximum transformed rate decreases. The content of retained austenite transformed isothermally is much smaller as compared to the athermal condition. The amount of isothermally formed martensite does not show linear relationship with the temperature, where an optimal isothermal temperature for GCr15 steel is 193 K in this work. XRD measurement result showed that the content of retained austenite decreased with the decrease of treating temperature in practical DCT, where the content was reduced up to 4.2% after DCT at the lowest temperature combined with tempering. DCT enhanced the precipitation of θ-carbides during tempering and altered the precipitation behavior by advancing the precipitated temperature of θ-carbides from 340 °C to 315 °C. The tempered hardness of samples was improved by DCT, which can be attributed to the enhanced carbides precipitation during tempering and lower content of retained austenite after DCT. The improvement was also affected by tempering and austenitizing temperatures. It was concluded that the performance improvement induced by DCT was most evident if DCT was conducted between higher temperature quenching and lower temperature tempering. DCT also affected the decomposition of retained austenite during tempering by decreasing the activation energy of decomposition by up to 38.13 KJ/mol, which indicated a lower thermal stability of retained austenite after DCT. Microstructure observation indicated that the substructure of the new formed martensite was dominated by ultra-fine twins, which derived from the accommodated strain induced by martensitic transformation during DCT. The transformation strain induced by DCT also causes more dislocations in the microstructure, which provides more nucleation sites for the precipitation of θ-carbides during tempering.

Effect of Heat Treatment on Microstructure and Impact Toughness of a Tungsten-Molybdenum Powder Metallurgical High-Speed Steel

Effect of Deep Cryogenic Time on Martensite Multi-Level Microstructures and Mechanical Properties in AISI M35 High-Speed Steel

Microstructural variations and mechanical properties of deep cryogenic treated AISI M35 high-speed steel tempered at various temperatures

Effect of Heat Treatment on Microstructure and Properties of Improved 40crni2si2mov Steel

Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel

Effects of deep cryogenic treatment on the microstructure and friction performance of M35 high-speed steel

Effects of traditional heat treatment and a novel deep cryogenic treatment on microstructure and mechanical properties of low-carbon high-alloy martensitic bearing steel

Effect of Deep Cryogenic Treatment on Dilatometric Curve and Tribological Properties of High Speed Steel

Effect of multiple deep cryo-treating and tempering on microstructure and property evolution of high carbon bearing steel

Effect of Deep Cryogenic Treatment on Microstructure and Properties of M35 High Speed Steel

Effect of Heat Treatment on Microstructure and Properties of Powder Metallurgy High-Speed Steel Prepared by Hot Isostatic Pressing

In Situ Observation on Microstructural Development of High-Speed Steel During Carbon Partitioning Process

Effects of deep cryogenic treatment on the microstructure evolution, mechanical and thermal fatigue properties of H13 hot work die steel

Hardness and toughness investigations of deep cryogenic treated cold work die steel

Effect of Heat Treatment on Structure and Properties of B Alloyed High Speed Steel for Rolling Mill Rolls

Effect of Microstructure Evolution on Impact Toughness in Advanced Ultra-High Strength Steel

Cryogenically martensitic transformation and its effects on tempering behaviors of bearing steel

Features of the Heat Treatment of High Speed Steel

The Effect of Multi-Step Tempering and Partition Heat Treatment on 25cr2ni3mov Steel’s Cryogenic Strength Properties

Improving impact toughness of Fe–20Mn–9Al-1.5C–2Ni–3Cr low-density steel by optimizing grain boundaries via multi-stage heat treatment without compromising high strength and ductility

Effect of Tempering Heat Treatment on the Microstructure and Impact Toughness of a Ni-Cr-Mo-V Steel Weld Metal