Abstract:Intermetallic (Si, Sn, Sb etc.) electrodes offer significantly higher volumetric and gravimetric energy density compared to the widely used graphite-based electrodes, which make them promising candidates for next generation Li-ion cells for transportation applications. [1] However, numerous studies have demonstrated that the inherently non-passivating behavior of intermetallic electrodes in standard organic carbonate-based Li-ion electrolytes [2] is aggravated by significant volume changes during the charging and discharging processes. Mechanical stresses from volume change lead to particle decrepitation, resulting in electronic isolation of particles, loss of mechanical integrity of composite electrodes and interfacial instability. Particle factures expose fresh electrode surface to the electrolyte during cycling, leading to formation of a thick film of electrolyte reduction products, causing impedance rise, capacity loss and lithium inventory shift in the cell. [3] The solid electrolyte interphase (SEI) layer, which forms at the electrode/electrolyte interface during the initial charge/discharge cycles, is the key component that determines the long-term stability and cycling behavior of negative Li-ion battery electrodes. [4-6] Electrolyte reduction and SEI layer formation on these electrodes usually take place at potentials below 1.8V vs. Li/Li+ and accompany the formation of Li-Me phases, the so-called “Me-Li alloying” process at E <0.8 V vs. Li/Li+. The exact mechanism of the SEI formation processes on Si, Sn, Sb and their alloys with lithium, the SEI composition and the effect on the electrode electrochemical cycling performance is not well understood. Interestingly, model studies on Sn single crystal electrodes in organic carbonate electrolytes revealed a strong correlation between the crystal surface orientation and the SEI composition. [7,8] A similar study of the composition of the SEI on a silicon monocrystal electrode showed strong effects of different SEI formation protocols, presence/absence of intrinsic SiO2, electrolyte composition and impurities e.g., HF. On the other hand, SEI-forming electrolyte additives such as vinylene carbonate (VC) and fluoroethylene carbonate (FEC) are known to alter the composition and properties of the SEI on Si and improve the electrode electrochemical performance. This study involves rigorous charcaterization studies of tin, silicon, Si-based alloys, and composite Si-based model electrodes to determine and understand the key thermodynamic and kinetic parameters, which enable their function and operation in Li-ion battery systems. Advanced diagnostic tools are used to gain fundamental insight into mechanism of intermatallic-based electrodes failure. An emphasis is placed on in situ methods that use multiple techniques at the same time e.g., imaging with spectroscopy. The diagnostic experimental strategies involve evaluations of model silicon and other intermetallic model composite electrodes as well as studies of the properties of the individual components and their interfaces in a carefully designed and well defined experimental systems. The interfacial instability of the electrolyte and the uncertainty associated with the formation of a stable solid electrolyte interphase (SEI) are the key problems being addressed. Acknowledgements This work was supported by the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231, under the Applied Battery Research for Transportation (ABR) Program and Award Number DE-EE0006443. References I.H. Son et al., Nat. Commun., 6 (2015) 7393\ C.K. Chan et al., Nat. Nanotechnol., 3 (2008) 31-35. B. Philippe et al., Chem. Mater., 24 (2012) 1107-1115. E. Peled, J. Electrochem Soc, 126, 2047 (1979). D. Aurbach et al., Electrochim. Acta, 45, 67 (1999). J. S. Gnanaraj etal., J. Electrochem. Soc, 154, A185 (2007) R. Qiao et al., Avanced Materials Interfaces, 1, n/a (2014). I. T. Lucas, J. Syzdek, and R. Kostecki, Electrochem Commun, 13, 1271 (2011).

Micromechanism in All-Solid-State Alloy-Metal Batteries: Regulating Homogeneous Lithium Precipitation and Flexible Solid Electrolyte Interphase Evolution

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Investigation of Solid Electrolyte Interface Formation in Li3as Electrode Material in a Solid-State Battery Configuration

Electrochemical behavior of elemental alloy anodes in solid-state batteries

Issue of Lithium-indium Anode in High Energy and Power All-Solid-State Lithium Batteries

Forming Artificial Solid-Electrolyte-Interfaces between Lithium Metal Anodes and Halide and Sulfide Solid Electrolytes in All-Solid-State-Batteries Via Spatial-Atomic-Layer-Deposition

Tunable structure and dynamics of solid electrolyte interphase at lithium metal anode

Favorable Interfacial Chemomechanics Enables Stable Cycling of High-Li-Content Li–In/Sn Anodes in Sulfide Electrolyte-Based Solid-State Batteries

Unravelling the convoluted and dynamic interphasial mechanisms on Li metal anodes

Favorable Interfacial Chemomechanics Enables Stable Cycling of High Li-Content Li-In/Sn Anodes in Sulfide Electrolyte Based Solid-State Batteries

In Situ Analysis of Interfacial Morphological and Chemical Evolution in All‐Solid‐State Lithium‐Metal Batteries

Integrated Interface Configuration by In-Situ Interface Chemistry Enabling Uniform Lithium Deposition in All-Solid-state Lithium Metal Batteries

Superior Lithium-Metal All-Solid-State Batteries with In-situ formed Li 3 N-LiF-rich Interphase

In Situ Constructed 3D Lithium Anodes for Long‐Cycling All‐Solid‐State Batteries

Nanoscale Visualization of Lithium Plating/Stripping Tuned by On‐site Formed Solid Electrolyte Interphase in All‐Solid‐State Lithium‐Metal Batteries

In Situ and Ex Situ Studies of Interfacial Processes on Intermetallic Li-ion Anodes

Li Metal Anode Interface in Sulfide‐based All‐solid‐state Li Batteries

Li–Sb Alloy Formation Strategy to Improve Interfacial Stability of All‐Solid‐State Lithium Batteries

Gradiently Sodiated Alucone as an Interfacial Stabilizing Strategy for Solid‐State Na Metal Batteries

Revealing Dynamic Evolution of the Anode‐Electrolyte Interphase in All‐Solid‐State Batteries with Excellent Cyclability

Recent Progress in Understanding Solid Electrolyte Interphase on Lithium Metal Anodes